ESAB A6 Slide Manual de usuario
Valid for serial no. 452--xxx--xxxx0443 394 060 2006--07--13
A6 Slide
101103105102021104022100020040060
Bruksanvisning
Brugsanvisning
Bruksanvisning
Käyttöohjeet
Instruction manual
Betriebsanweisung
-- 2 --
Rätt till ändring av specifikationer utan avisering förbehålles.
Ret til ændring af specifikationer uden varsel forbeholdes.
Rett til å endre spesifikasjoner uten varsel forbeholdes.
Oikeudet muutoksiin pidätetään.
Rights reserved to alter specifications without notice.
Änderungen vorbehalten.
SVENSKA 4..............................................
DANSK 24................................................
NORSK 44................................................
SUOMI 64................................................
ENGLISH 84..............................................
DEUTSCH 104.............................................
-- 3 --
ENGLISH
-- 8 4 --
TOCe
1SAFETY 85...........................................................
2 TECHNICAL DESCRIPTION 87.........................................
2.1 General 87..................................................................
2.2 The A6 slide consists of: 87....................................................
2.3 TECHNICAL DATA 88........................................................
2.4 The carrying capacity of the slide 88............................................
2.5 The linear bearing of the runner 89.............................................
2.6 The distance between the fixation of the slide profile and the line of application of the load
91
2.7 Deformation of the slide profile under load 92....................................
2.8 Slide transfer 95.............................................................
3 INSTALLATION 96....................................................
3.1 General 96..................................................................
3.2 Connections of the runner 96..................................................
3.3 Connections of the slide profile 96..............................................
3.4 Fitting of vertical cross saddle 96...............................................
3.5 Recommended way of lifting servo slides 97.....................................
4 OPERATION 98.......................................................
4.1 General 98..................................................................
4.2 Changing the speed range 98..................................................
5 MAINTENANCE 100....................................................
5.1 General 100..................................................................
5.2 Daily: 100....................................................................
5.3 Every month: 100.............................................................
5.4 Every year 100................................................................
5.5 As necessary 100.............................................................
5.6 In case of a long standstill 100..................................................
5.7 Replacing the linear bearings 101................................................
6 ORDERING OF SPARE PARTS 103......................................
DIMENSION DRAWING 124................................................
SPARE PARTS LIST 125...................................................
-- 8 5 --
fgb5safE
1SAFETY
Users of ESAB servo slides have the ultimate responsibility for ensuring that anyone
who works on or near the servo slide observes all the relevant safety regulations.
The following recommendations should be observed in addition to the standard re-
gulations that apply to the work place.
1. General
All manoeuvres must be performed according to the given instructions by
personnel well familiar with the functions of the servo slide.
An incorrect manoeuvre, caused by a wrong move or an incorrect release of a
functional sequence, can lead to an abnormal situation that can injure the
operator and cause damage to the equipment.
Personnel working with the servo slide must be well familiar with:
Sthe handling of the slide
Sthe location of emergency stops
Sthe function of the slide
Sall relevant safety regulations
2. Live electrical components are usually semi--protected.
SAny work on electrical units shall be carried out by a qualified electrician.
3. Danger of the load falling down
SMake sure the base will resist all types of forces coming up during operation.
SCheck that the slide is fastened to the base with at least 4 M10 or M12 Allen
screws.
SNever overload the slide (see on page 88 the carrying capacity of the slide)
SCheck the condition of the belt regularly (at least every 200 hours).
SReplace the belt at least every 5 years, or as necessary.
N.B.
When replacing the belt or the belt pulley the load must be secured. Read
the pages 98 -- 99.
In case of a belt rupture the load will fall down.
WARNING!
4. Danger of getting clamped
SWhen the runner goes towards its end position
SWhen the belt protection is dismounted
5. Maintenance
SLubrication and maintenance of the slide must not be carried out when the
slide is in operation.
GB
-- 8 6 --
fgb5safE
GB
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND
OTHERS. TAKE PRECAUTIONS WHEN WELDING. ASK FOR YOUR
EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE BASED ON
MANUFACTURER’S HAZARD DATA.
ELECTRIC SHOCK -- Can kill
SInstall and earth the welding unit in accordance with applicable standards.
SDo not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing.
SInsulate yourself from earth and the workpiece.
SEnsure your working stance is safe.
DANGER OF GETTING CLAMPED
SMoving parts can cause damage. Therefore, be very careful!
FUMES AND GASES -- Can be dangerous to health
SKeep your head out of the fumes.
SUse ventilation, extraction at the arc, or both, to keep fumes and gases from
your breathing zone and the general area.
ARC RAYS -- Can injure eyes and burn skin
SProtect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing.
SProtect bystanders with suitable screens or curtains.
FIRE HAZARD
SSparks (spatter) can cause fire. Make sure therefore that there are no
inflammable materials nearby.
NOISE -- Excessive noise can damage hearing
SProtect your ears. Use ear defenders or other hearing protection.
SWarn bystanders of the risk.
MALFUNCTION
SCall for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
READ AND UNDERSTAND THE OPERATING MANUAL BEFORE
INSTALLING OR OPERATING.
WARNING
-- 8 7 --
fgb5d1ea
2 TECHNICAL DESCRIPTION
2.1 General
The A6 slide is designed to carry and transfer welding heads of different types of
welding plants. The slide can be mounted across the weld joint -- single or in a cross
saddle -- for adjustment or joint tracking. It can also be mounted along the weld joint
to bring about a welding movement.
The A6 slide is controlled over:
SControl box A6 GMD for joint tracking. (See instruction manual 443 403 xxx)
SControl box A6 PAK for positioning. (See instruction manual 443 405 xxx)
SControl box PEH for travel motion. (See instruction manual 443 745 xxx)
The A6 slide is a motorized linear slide. All movable parts are lodged in ball
bearings. The slide is available in different setting lengths from 60 to 1030 mm (see
dimension drawing on page 124) and in two different speed ranges.
2.2 The A6 slide consists of:
1. Slide profile, stiff U--profile.
2. Runner, lodged in open ball bushings, run-
ning over the axes which are supported by
the slide profile in their full length.
The driving system contains:
3. DC motor with worm gear.
4. Tooth belt transmission with built--in friction
clutch.
5. Ball screw with nu.
GB
-- 8 8 --
fgb5d1ea
2.3 TECHNICAL DATA
Setting length
(mm) 60 120 180 240 300 420 540 730 1030
Total length (mm) 305 365 425 485 545 665 785 1025 1385
Weight (kg) 11,5 13,2 15,0 16,7 18,5 21,9 25,4 30,9 38,8
A6 Slide
Max control voltage 42 V DC
Max speed at 42 V DC 70 cm/min (175 cm/min with reversed
gear wheels in transmission)
Continuous A--weighted noise pressure 42 dB
Play of runner in the longitudinal direc-
tion of the slide 0,1 mm
Other play 0
Max ambient air temperature 80°C
Max load dimensions at full setting
length
Setting length 60 to 540: b=62
Setting length 60 to 730: b=86
Setting length 60 to 1030: b=117
2.4 The carrying capacity of the slide
To simplify the schematical representation it is assumed that the load on the slide is
a weight and that the different mounting positions are confined to:
SVertical position
SStanding horizontal position
SLying horizontal position.
With the following co--ordinate directions the force of gravity works in the y, x and z
directions.
GB
-- 8 9 --
fgb5d1ea
2.5 The linear bearing of the runner
Max permissible momemt--free load on the runner of the slide is 150 kg irrespective
of the mounting position of the slide.
Max permissible moment--generating load on the runner of the slide depends on the
mounting position. The centre of gravity of the load can be displaced from the centre
of the runner within an area, the further limit of which depends on the size of the load
according to the three diagrams below, where the slide is seen from above.
Max. load at vertical mounting Max load at standing horizontal mounting
Max load at lying horizontal mounting
GB
-- 9 0 --
fgb5d1ea
Examplel 1:
SAn A6 SFD1 automatic welding machine is
mounted on a standing cross saddle.
SNote that the wire drum and the drum holder are
mounted on th slide profile of the vertical slide.
Example 1a:
SThe load on the vertical slide is about 43 kg.
SThe centre of gravity (TP1) is displaced 0,35 m
from the runner of the vertical slide in the z
direction.
SThe displacement of the centre of gravity in the x
direction can be neglected.
SThe load is far below the permissible load of 110
kg in this position.
*1) Permissible position of the centre of gravity at a
load of 40 kg.
*2) Permissible position of the centre of gravity at a
load of 100 kg.
Example 2:
SA load of 50 kg is fitted on a lying
horizontal slide.
SThe centre of gravity is displaced 0,4
m in the x direction.
SThe centre of gravity can also be dis-
placed 0,17 m in the y direction with-
out the max load being exceeded.
*1) Permissible position of the centre of
gravity at a load of 50 kg.
GB
Tabla de contenidos
Otros manuales de Sistema de soldadura de ESAB
ESAB
ESAB KHM 190 HS Manual de usuario
ESAB
ESAB PT-25 Manual de usuario
ESAB
ESAB Caddy Professional 250 Manual de usuario
ESAB
ESAB Rogue EM 190 PRO Manual de usuario
ESAB
ESAB LAF 1251 Manual de usuario
ESAB
ESAB Mig 4004i Manual de usuario
ESAB
ESAB Aristo Mig U5000i 400 V Manual de usuario
ESAB
ESAB Origo Mig 410 Manual de usuario
ESAB
ESAB PT-26 Manual de usuario
ESAB
ESAB Retrofit Aristo Mig 4004i WeldCloud Manual de usuario
ESAB
ESAB Origo Mig 4004i A44 Manual de usuario
ESAB
ESAB MobileFeed 301 AVS Manual de usuario
ESAB
ESAB Origo M11 Feed 302 Manual de usuario
ESAB
ESAB Caddy Arc 151i Manual de usuario
ESAB
ESAB MultiMaster 160 Manual de usuario
ESAB
ESAB LHI 825 Guía
ESAB
ESAB Rogue ES 150i Manual de usuario
ESAB
ESAB Origo Arc 250 edw Guía
ESAB
ESAB Fabricator EM 401i Manual de usuario
ESAB
ESAB Origo Mig 3001i Manual de usuario
Manuales populares de Sistema de soldadura de otras marcas
TAFA
TAFA 30*8B35 Manual de usuario
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manual de usuario
CIGWELD
CIGWELD 636804 Guía rápida
Red-D-Arc
Red-D-Arc DC-400 Manual de usuario
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario
Elettro
Elettro HI-MIG 3000 SYNERGIC Manual de usuario
