EROAD Ehubo Manual de usuario
EROAD Ehubo®
Installation Guide
2
1
Congratulations on purchasing your EROAD Ehubo®
IMPORTANT: Do not install or use the Ehubo until
you have read this Installation Guide thoroughly.
EROAD recommends the use of a professional automotive technician to
install the Ehubo in your vehicle. Please make this Guide available to your
installer and keep it for future reference.
The Ehubo is easy to install by carrying out the following steps as
described in this Guide:
1. Make sure to read the Safety Information section, familiarize yourself
with the local laws regarding the installation and use of the Ehubo,
and use and follow all standard safety precautions.
2. Choose a suitable mounting location and mount the Ehubo.
3. Install the Ehubo by connecting it to the vehicle.
4. Complete the installation by following the Ehubo’s on-screen guide.
Refer to “Replacement Installation” on page 10 if you are installing a replacement Ehubo
© 2015 EROAD. Doc 100200AD1.7. 12/2015.
By using this Ehubo you are agreeing to be bound by EROAD’s
Terms of Use that can be located at www.eroad.com.
2
Please read carefully before beginning installation!
LEGAL NOTICE AND DISCLAIMER
The legislation and rules concerning the installation and operation of GPS driver aids and messaging
devices such as the Ehubo vary from each country and state. Please familiarize yourself with the laws
of the jurisdiction(s) in which the vehicle will be operated in prior to installing and using the Ehubo.
Driving laws place the responsibility on the driver to correctly install and use GPS driver aids. It is
therefore the Customer’s sole responsibility to install and use the Ehubo in a manner that complies
with the law and will not cause accidents, personal injury or property damage. The owner of this
Ehubo is solely responsible for observing safe driving practices.
EROAD DISCLAIMS ALL LIABILITY FOR ANY USE OF THIS EHUBO IN A WAY THAT MAY CAUSE
ACCIDENTS, DAMAGE OR VIOLATE THE LAW.
TO THE MAXIMUM EXTENT PERMITTED BY LAW, ALL REPRESENTATIONS AND WARRANTIES
(EXCEPT ANY WHICH MAY NOT LAWFULLY BE EXCLUDED) ARE EXPRESSLY EXCLUDED, INCLUDING
WITHOUT PREJUDICE TO THE GENERALITY OF THE FOREGOING, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
As EROAD is continuously improving its products, EROAD may make changes to the Ehubo at any
time which may not be reflected in this document. Please contact your nearest EROAD oce if you
require any further assistance.
PERSONAL PROTECTIVE EQUIPMENT (PPE)
Federal, national or local health and safety regulations may require wearing appropriate Personal
Protective Equipment (PPE). PPE may include items such as safety glasses, safety shoes, work gloves,
hard hat, high visibility vest, and work uniform. Make sure to comply with appropriate standards and
check with customers or third parties to verify whether they have additional PPE requirements.
INSTALLATION
• Installers and contractors must follow all health and safety regulatory requirements to ensure a safe
and healthy work environment.
• Whenever the equipment is parked, the parking brake shall be set. Equipment parked on inclines
shall have the wheels chocked and the parking brake set.
• Equipment, or parts thereof, which are suspended or held aloft by use of slings, hoists, or jacks shall
be substantially blocked or cribbed to prevent falling or shifting before employees are permitted to
work under or between them.
• Installing and servicing electronic devices can be hazardous due to electrical components.
Make sure to create a safe working environment to avoid hazards and to ensure correct and safe
installation and operation.
• EROAD recommends the use of a qualified professional automotive technician to install the Ehubo.
Make this Installation Guide available to the appropriate personnel. Store it for future reference.
• To avoid damage do not run cables close to heat sources, sharp edges or other obstacles
that might damage them.
• Do not run cables directly next to safety-relevant devices.
• Place all wiring under the dash to avoid creating a hazard.
• Do not damage existing wiring and components when drilling the dashboard.
• Some countries and states prohibit the installation of GPS driver aids on windshields. Where it is
lawful to install the Ehubo on the windshield, to minimize obstruction of the driver’s field of view, it
should be positioned as low as possible and closest to the driver door.
Important Safety Information
3
• Avoid fitting the Ehubo in a location that could cause injury to a driver or passenger in a crash. This
includes potential head strike zones on the windshield or dashboard, or other locations where a
deploying airbag may contact the Ehubo.
• Do not block or impair the deployment of airbags and other safety-relevant devices.
• Avoid placing the Ehubo where it may impede or limit the driver’s movement when driving or exiting
the vehicle (including in an accident).
• After installation, check that all safety-relevant equipment is working properly.
OPERATION
• Familiarize yourself with local laws concerning the use of GPS driver aids. Some countries and states
prohibit drivers from viewing screens or making or receiving text messages while driving a vehicle.
• To avoid driver distraction, the Ehubo screen is initially configured to automatically turn o when
movement is detected.
• Where the Ehubo screen has been activated to turn on during driving, minimize the amount of time
spent viewing the screen.
• Only operate or look at the Ehubo when it is safe to do so. Do not message, change settings or
access functions while driving. Pull over before you wish to attempt such activities. Always keep your
hands free to operate the vehicle while driving. Your first consideration while driving should be road
safety.
• Where the screen displays the speed limit or the vehicle’s speed, this is for information only. Please
ensure that you observe all posted speed limits and drive to the conditions.
• Do not use sharp-edged objects on the Ehubo touch screen.
• The Ehubo is not waterproof. Do not spill any liquid on it.
• Protect the Ehubo from extreme temperatures. Operating temperature for the Ehubo is between
-20°C/-4°F and 85°C/185°F.
• Always follow local regulations when disposing of the Ehubo.
• Do not dispose of the battery in trash cans, fire or water.
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
4
EROAD Ehubo
(pre-fitted wiring loom)
EROAD
Fuse kit
(permanent/switched power)
EROAD Ehubo®
Installation Guide
This installation guide
Cable ties
Rear hatch
security plugs
Inside the box
RAM
RAM
Ehubo mount
High–strength adhesive tape
(optional, for tape mount)
Mounting
plate
Screws, nuts and washers to mount Ehubo
2 x ¾”/ 19mm screws + washers
4 x ½”/ 13mm counter sunk
screws + nyloc nuts
4 x 1”/ 25mm screws + nuts
A B
TECHNICAL CLEANING WIPE
Alcohol wipe
C
F
D
E
Open your Ehubo box and check that everything is inside.
5
TAPE MOUNT
• Clean flat surface with alcohol wipe
• Fit mounting plate (A) to mount using
counter sunk screws/holes and nuts (D)
• Apply adhesive tape (B) to mounting
plate and firmly press to surface
PERMANENT MOUNT
Attach mount to dash
using mounting plate (A),
screws and nuts (E).
or
Attach Ehubo to the mount
using screws and washers (C).
Use of the washers is essential to
reliably secure the Ehubo!
Route the Ehubo wiring out of
the way and down the back of
the dashboard.
NOTE: If swapping mounting option do not re-use nyloc nuts, use unused nuts as supplied.
Insert the two rear hatch security plugs. The plugs are keyed and only fit in
their correct position. Proceed with 2A PERMANENT MOUNT (dashboard) or
2B TAPE MOUNT (windshield or flat surface).
1
2B2A
A
AB
3 4
Mount the Ehubo
C
E
The Ehubo can be mounted on the dashboard or windshield (where permitted by law where
the vehicle is being operated). For windshield mount or temporary installation on a flat
surface please use the adhesive tape supplied.
NOTE: Choose the mounting location for your Ehubo carefully and ensure that it complies
with all local regulations. Make sure that the Ehubo does not impair the driver’s visibility,
does not pose a risk in the event of an accident, does not interfere with any systems used
in the operation of the vehicle, does not block or impair the deployment of the airbag, and
has a good view of the sky. Choose a location that does not expose the Ehubo to excessive
temperature or vibration.
D
6
Install the Ehubo
NOTE
• The engine must be turned o prior to installing the Ehubo.
• Do not connect in any way to a CANBUS or other engine management system.
• Power supply must not be taken from any ABS/EBS braking system.
The Ehubo needs a permanent power source and a good view of the sky to operate
optimally. While the vehicle is o, the Ehubo will shut down to a low power mode and will
draw a very small current from the vehicle supply. Remove the Ehubo permanent power
fuse if the vehicle is in storage or parked up for more than a month to avoid discharging the
vehicle battery.
WIRING
The Ehubo is fitted with a wiring loom which is
used to connect to the vehicle and for optional
digital inputs.
WIRE FUNCTION FUSE NOTES
Red +12V / 24V
DC Supply
Use supplied
fuse kit
Connect to a 12V or 24V DC permanent
power source.
Yellow Switched
Power
Connect to a switched power source that
is switched on when the engine is running
and o when the engine is not running
(true idle).
Black Ground Do not fuse Connect to an appropriate Grounding
location that is considered fit for purpose.
Orange Digital Input 1
Fuse individually
with 3A fuse
Optional digital inputs for
integration purposes.
Brown Digital Input 2
Gray Digital Input 3
NOTE: Fuse connections at vehicle
connection points to protect the
wiring in case of a short circuit.
7
NOTE: If the screen remains black or if you cannot successfully complete
the instructions on the screen, the wiring of the Ehubo may not be quite
right. Please refer to the Wiring Diagrams in this Installation Guide or to the
Troubleshooting section and adjust your wiring. If the screen still remains
black, please contact the EROAD Helpdesk.
The installation remains unfinished until the on-screen instructions have
been successfully completed!
INSTALLING THE EHUBO
Refer to wiring diagrams and table on previous page.
1. Connect the black wire to an appropriate Grounding location that is
considered fit for purpose.
2. Connect the red wire to a permanent power source.
3. Connect the yellow wire to a switched power source that is switched on
when the engine is running and o when the engine is not running (true idle).
4. If required, connect additional wires (orange, brown and gray) for
monitoring vehicle activity on three digital inputs.
Refer to “Wiring Diagram – Additional Inputs” and table above.
5. Store all unused wires neatly, insulated and secured using cable ties supplied.
6. Pull the sticker and screen protection film o the Ehubo screen.
7. To complete the installation, follow the instructions on the screen.
At the end of the process the Ehubo Home screen will appear, and
the installation is complete.
8
Dashboard
Wiring Diagram – Standard
YELLOW
BLACK
Permanent Power (12V or 24V)
Switched
Power (Engine on/o)
Ground
RED
IGN
+ve
Any unused wiring
should be stored
neatly, insulated
and secured
The switched input
is used to report on
engine running time
and true idle time
Fuses must be fitted
at connection point.
This is to protect the
wire in case of a short
Cut wire loop and
connect fuse inline
Note: Ensure
wiring is neatly
routed to
under the dash
RAM
EROAD
Otros manuales para Ehubo
4
Tabla de contenidos
