Ergotron Zido Manual de usuario

1 of 4

300-5666-00 rev. B • 06/16

Built with Anthro-DNA™

Zido®Single Monitor Mount

Product Part#

Zido Single Monitor Mount ZOMSzz

For the latest User Installation Guide please visit: www.ergotron.com

User's Guide

2 of 4

300-5666-00 rev. B • 06/16

Zido Pole Flat Panel Mount, Single Quantity Part Number

01 Outer Bracket 1 225-2661-00

02 Inner Bracket 1 225-2980-00

03 1/4-20 x 1/2" Button Head Screw 4 325-5003-00

04 #10-24 x1/2" Self-threading Screw 2 325-5464-00

05 OmniMount Small Tilt/Pan Mount 1 835-5764-00

06 M6 x 12mm Button-head Screw 2 325-5757-00

07 OmniMount VESA Plate 1 697-915-00

08 Flat Pattern Hardware Kit (not shown) 1 697-563-00

M4 x 12mm Philips Head Screw 4 M-A

M5 x 12mm Philips Head Screw 4 M-B

(not needed in assembly)

M6 x 12mm Philips Head Screw 4 M-C

(not needed in assembly)

09 OmniMount Hardware Kit (not shown) 1 697-878-00

Security Allen Screw 2 P-C

Washer 2 P-D

Allen Wrench

Fastener quantities listed are the minimum needed for your assem-

bly. Your shipment may contain a few extras.

TOOLS

A 5/32" hex driver (provided with

your Zido Cart) is required for this

assembly.

PARTS LIST

Before beginning assembly of your Zido Single Monitor

Mount, please review the parts list to verify that your

shipment is complete.

3 of 4

300-5666-00 rev. B • 06/16

Outer Hole

M6 x 12MM Screws

1/4-20 X 1/2"

Button-head

Screws

1/4-20 x1/2” Button-hd Screw

5003

M6 x 12mm Button-hd Screw

325-5757-00

Self-threading Screw

325-5464-00

Top of assembly

Curved Slot

Knob

Self-thread-

ing Screws

STEP 1

Attach the VESA plate to your monitor

Place the VESA bracket in position on the back of the monitor. Attach

using four M4 x 12MM Screws (part #M-A) provided in the plastic bag. The

VESA bracket accommodates 75mm and 100mm hole patterns. For this

installation, you may also use the screws that came with your monitor.

STEP 2

Assemble the Brackets

Align the Tilt/Pan Mount with the 2 outer holes that are directly above and

below the 6 small holes in the center of the outer bracket. Secure using 2

M6 x 12mm Button-head Screws using the 5/32" hex key. (A)

Slide the inner bracket into the outer bracket so that the holes on each side

align. Using the 5/32” hex key, secure with 4 1/4-20 x 1/2" Button-head

Screws. (B)

STEP 3

Install the Brackets and the Monitor

Slip the bracket assembly over the top of the Zido tube, with the assembly

facing the front of the cart. Be sure the assembly is installed right side up,

with the curved slot being at the top of the assembly (A). Secure with 2 self-

threading screws. (B).

Note: These fasteners are creating the threads in the tube, so the rst few turns will require

some force.

Lift the monitor into place in front of the Tilt/Pan Mount. Slide the VESA

bracket into the curved slot in the Tilt/Pan Mount.

Secure the monitor to the Tilt/Pan Mount using 2 Security Allen Screws (part

# P-C) using the Allen Wrench (part #P-E), making sure to place a washer

(part #P-D) between the screw and the VESA plate.

To adjust the position of the monitor, loosen the knob on the side of the

Tilt/Pan Mount to adjust and tighten again when the monitor is in the

desired position.

CONGRATULATIONS!

YOUR ZIDO SINGLE MONITOR MOUNT ASSEMBLY IS COMPLETE!

4 of 4

300-5666-00 rev. B • 06/16

All trademarks are the property of their respective companies. Anthro is a registered trademark and brand of Ergotron Inc.

Anthro-DNA is a trademark of Ergotron Inc.

For local customer care phone numbers visit: http://contact.ergotron.com

For Service visit: www.ergotron.com

For Warranty visit: www.ergotron.com/warranty

Otros manuales de Rack y soporte de Ergotron

Ergotron

Ergotron WorkFit LX Manual de usuario

Ergotron

Ergotron Grommet Mount Kit Manual de usuario

Ergotron

Ergotron Neo-Flex Mobile MediaCenter VHD Manual de usuario

Ergotron

Ergotron UKMCBK Manual de usuario

Ergotron

Ergotron Neo-Flex Manual de usuario

Ergotron

Ergotron LX3 Manual de usuario

Ergotron

Ergotron Neo-Flex OM10245 Manual de usuario

Ergotron

Ergotron Neo-Flex Widescreen Stand Manual de usuario

Ergotron

Ergotron LCD/Notebook Arm Guía de instalación

Ergotron

Ergotron Neo-Flex 45-174-300 Dimensiones

Ergotron

Ergotron LX Desk Mount LCD Arm Manual de usuario

Ergotron

Ergotron WorkFit-P Manual de usuario

Ergotron

Ergotron LX Desk Mount LCD Arm Manual de usuario

Ergotron

Ergotron WorkFit-S Manual de usuario

Ergotron

Ergotron Neo-Flex Slide-out Manual de usuario

Ergotron

Ergotron StyleView Guía de solución de problemas

Ergotron

Ergotron Neo-Flex Mobile MediaCenter VHD Manual de usuario

Ergotron

Ergotron LX Desk Mount LCD Arm Manual de usuario

Ergotron

Ergotron SV Combo Manual de usuario

Ergotron

Ergotron Workfit-SR Manual de usuario

Ergotron

Ergotron Neo-Flex 33-310-060 Manual de usuario

Ergotron

Ergotron MXV Manual de usuario

Ergotron

Ergotron MXV Manual de usuario

Ergotron

Ergotron Power Strip Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario