Erbauer ERB337TCB Manual de instalación
ERB337TCB Original Instructions
ERBAUER 750W TILE CUTTER
SAFETY AND OPERATING MANUAL
WARRANTY
YEARS
ERBAUER 750W TILE CUTTER
GUARANTEE
This product carries a guarantee of 24 months. If your product develops
a fault within this period, you should in the first instance contact the retailer where
the item was purchased.
This guarantee specifically excludes losses caused due to:
- Fair wear and tear
- Misuse or abuse
- Lack of routine maintenance
- Failure of consumable items (such as batteries)
- Accidental damage
- Cosmetic damage
- Failure to follow manufacturer’s guidelines
- Loss of use of the goods
This guarantee does not affect your statutory rights. This guarantee is only valid
in the UK.
For further technical advice, spare parts or repair service (outside of guarantee)
please contact your retailer quoting your Erbauer model number
Congratulations on your purchase of a quality power tool from Erbauer (UK)
Ltd. This product should give you reliable service but for your peace of mind
this power tool does carries a 24-month guarantee, the terms of
which are detailed below.
If this product develops a fault within the guarantee period contact your
retailer.
Please retain this handbook in case you need to refer to safety, care or
guarantee information in the future.
GENERAL SAFETY INSTRUCTIONS
WARNING! Read all instructions Failure to follow all instructions listed
below may result in electric shock, fire and/or serious injury. The term
"power tool" in all of the warnings listed below refers to yourmains operated (corded)
power tool or battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
1. keep work area clear. Cluttered areas and benches invite injuries.
2. Consider work area environment Do not expose tools to rain. Do not
use tools in damp or wet locations. Keep work area well lit. Do not use
tools in the presence of flammable liquids or gases.
3. Guard against electric shock Avoid body contact with earthed or grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
4. Keep other persons away. Do not let persons, especially children, not involved
in the work touch the tool or the extension cord and keep them away from the
work area.
5. Store idle tools. When not in use, tools should be stored in a dry locked-up place,
out of reach of children.
6. Do not force the tool. It will do the job better and safer at the rate for which it
was intended.
7. Use the right tool. Do not force small tools to do the job of a heavy
duty tool. Do not use tools for purposes not intended; for example do not use
circular saws to cut free limbs or logs.
8. Dress properly. Do not wear loose clothing or jewellery, they can be
caught in moving parts. Non-skilled footwear is recommended when
working out doors. Wear protective hair covering to contain long hair.
9. Use protective equipment. Use safety glasses. Use face or dusk mask if
working operations create dust.
10. Connect dust extraction equipment. If the tool is provided for the connection
of dust extraction and collecting equipment, ensure these are connected and
properly used.
11. Do not abuse the cord.Never yank the cord to disconnect it from the
socket. Keep the cord away from heat, oil and sharp edges.
12. Secure work. Where possible use clamps or a vice to hold the work. It
is safer than using your hand.
13. Do not overreach. Keep proper footing and balance at all times.
14. Maintain tools with care. Keep cutting tools sharp and clean for better
and safer performance. Follow instruction for lubricating and changing
accessories. Inspect tool cords periodically and if damaged have them
repaired by an authorised service facility. Inspect extension cords
ERBAUER 750W TILE CUTTER
periodically and replace if damaged. Keep handles dry, clean and free from
oil and grease.
15. Disconnect tools. When not in use, before servicing and when changing
accessories such as blades, bits and cutters, disconnect tools from the power supply.
16. Remove adjusting keys and wrenches. Form the habit of checking to see that
keys and adjusting wrenches are removed from the tool before turning it on.
17. Aboid unintentional starting. Ensure switch is in “off” p osition when
plugging in.
18. Use outdoor extension leads. When the tool is used outdoors, use only
extension cords intended for outdoor use and so marked.
19. Stay alert. Watch what you are doing, use common sense and do not operate
the tool when you are tired.
20. Stay alert. Check damaged parts. Before further use of tool, it should be
carefully checked to determine that it will operate properly and perform
its intended function. Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any other conditions
that may affect its operation. A guard or other part that is damaged
should be properly repaired or replaced by an authorised service centre
unless otherwise indicated in this instruction manual. Have defective
switches replaced by an authorised service centre. Do not use the tool if
the switch does not turn it on and off.
21. Warning. The use of any accessory or attachment other than one recommended
in this instruction manual may present a risk of personal injury.
22. Have your tool repaired by a qualified person. This electric tool complies
with the relevant safety rules. Repairs should only be carried out by qualified
persons using original spare parts, otherwise this may result in considerable
danger to the user.
ADDITIONAL SAFETY RULES FOR TILE CUTTERS
- The machine must be supplied through a residual current device (RCD) having a
rated residual operating current not exceeding 30 mA.
- Do not use diamond discs which are damaged or deformed.
- Replace table insert when worn.
- Use only diamond discs recommended by the manufacturer.
- Take care that the selection of the diamond discs is suitable for the material to be
cut.
- Wear suitable personal protective equipment when necessary, this could include
hearing protection to reduce the risk of induced hearing loss, respiratory protection
to reduce the risk of inhalation of harmful dust, wear gloves when handling
diamond discs and rough material.
- Never use blades on this machine.
- Use only diamond discs for which the maximum possible speed is not less than
the maximum spindle speed of the tool and the material to be cut.
- Faults in the machine, including guards or diamond discs, should be reported as
soon as they are discovered. Never use the machine without the guard in position.
- Maximum size of working piece should be 1m².
- This tile cutter should be used with limitations on ambient conditions (between
15°C and 30°C).
Wear goggles
Wear ear defenders
Wear a breathing mask
Wear gloves
ERBAUER 750W TILE CUTTER
SYMBOLS
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Conforms to relevant safety standards
WARNING – To reduce the risk of
injury,user must read instruction
manual.
Use only non fragmented discs
Hand protection shall be worn
Caution, risk of cuttin
Wear hearing protection.
Wear eye protection.
Wear respiratory protection.
1. Protective guard
2. Laser light On/Off switch
3. Extension table
4. Mitre cutting guide
5. On/Off switch
6. Working table
7. Laser battery box
8. Vertical fence
14 2
7
8
3
5 6
Rated voltage and frequency
Rated power
No load speed
Insulation class
Dimensions of the diamond disc
Weight
Working table size
Working table with extension table size
Maximum cutting depth
Laser Class
Laser wave length
230-240V~50Hz
750W S2:10min
3000/min
Class I
ø180mmx2.4mmxø22.2mm
12.0kg
380x400mm
440x580mm
30mm
II
650nm
CARACTERISTIQUES TECHNIQUES
ERBAUER 750W TILE CUTTER
93.5dB(A)
103.2db(A)
3dB(A)
A weighted sound pressure LpA
A weighted sound power: LwA
Uncertainty
The sound intensity level for the operator may exceed 85dB(A) and sound protection
measures are necessary.
NOISE
ACCESSORIES
The tile cutter is supplied with following accessories:
Mitre cutting guide
Parallel guide
45° vertical fence
Blade
Spanners
Water reservoir plug
Extension work table
1pc
1pc
1pc
1pc
2pc
1pc
1pc
Otros manuales para ERB337TCB
1
Tabla de contenidos
Otros manuales de Cortador de Erbauer
Manuales populares de Cortador de otras marcas
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Manual de usuario
Makita
Makita DCS552 Manual de usuario
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Manual de usuario
Makita
Makita 4112HS Manual de usuario
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Manual de usuario
Hitachi
Hitachi CM 4SB2 Guía de solución de problemas
