Epson ESC Manual de usuario

ESC/VP21 Command User's Guide for Business Projectors

ESC/VP21 Command User's Guide for

Business Projectors

ESC/VP21 Command User's Guide for Business Projectors

Table of Contents

Introduction to ESC/VP21- - - - - - - - - - - - - - - - - - - - - - - - - - 3

ESC/VP21 Command Formats - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4

Projector state and commands - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -5

Command transmission timing - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7

Command list and Applicable Models - - - - - - - - - - - - - - - - - - - - - - - - - - - -9

Command Details - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -12

Appendix - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -27

Revision History - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -28

electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. No

patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting

from the use of the information contained herein.

Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses,

costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications,

repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with SEIKO EPSON CORPORATION’s operating and

maintenance instructions.

SEIKO EPSON CORPORATION shall not be liable against any damages or problems arising from the use of any options or any consumable

products other than those designated as Original EPSON Products or EPSON Approved Products by SEIKO EPSON CORPORATION.

EPSON is a registered trademark of SEIKO EPSON CORPORATION. Easy MP is a trademark of SEIKO EPSON CORPORATION. Macin-

tosh, Mac, and iMac are registered trademarks of Apple Computer, Inc. IBM is a registered trademark of International Business Machines

Corporation. Windows and Windows NT are registered trademarks of Microsoft Corporation in the United States of America.

General Notice:

Other product names used herein are also for identification purposes only and may be trademarks of their respective owners. EPSON disclaims

any and all rights in those marks.

ESC/VP21 Command User's Guide for Business Projectors

3 of 28

1.Introduction to ESC/VP21

ESC/VP21 is a control command and protocol for Epson projectors, which is used for A/V controller to control and monitor Epson projectors.

The command codes are comprised of ASCII codes. Therefore the command codes can be understood very easily and you can easily control

projectors using a PC with a terminal emulator such as Microsoft Hyper terminal.

Since ESC/VP21 is independent of communication protocols,Serial, USB or TCP/IP network can be used to transmit the commands to projec-

tors.

•Serial connection

A/V controllers normally use a serial connection to control projectors. Refer to Appendix for details.

•USB connection

A USB interface can be used to control a projector. Refer to Appendix for details.

•Network connection

After establishing a TCP session, ESC/VP21 commands can be sent to projectors. Refer to ESC/VP.net protocol manual.

Video camera

VTR

DVD

Controller Projector

Video

Serial

Projector with USB I/F

USB

Projector with network I/F

A/V controller

with network I/F

Hub

TCP/IP

ESC/VP21 Command User's Guide for Business Projectors

4 of 28

2.ESC/VP21 Command Formats

2.1.Set command format

A set command consists of a command and a parameter. Projector returns a colon after executing the command.

There are two types of parameters. One is fixed such as ON, OFF, or 21.Other is a step parameter such as INC, DEC or INIT.

INC increments the parameter by one.

DEC decrements the parameter by one.

INIT initializes the parameter.

Set command example 1 : SOURCE 21

Colon from projector Command Space Parameter Return

Set command example 2 : VOL INC

Colon from projector Command Space Parameter Return

2.2.Get command format

A get command consists of a command and ?. Projector returns a response parameter after executing the command.

Get command example : SOURCE?

Colon from projector Command ? Return

Response parameter example

SOURCE = 21

Colon from projector Command = Parameter

2.3.Null command

The null command is a command code of the return key code (Hex 0D). Projector returns a colon. The null command can be used to confirm

that the projector is in operation.

2.4.Illegal commands

Projector returns “ERR” and a return key code (Hex 0D) and a colon when it receives invalid commands.

ERR

ESC/VP21 Command User's Guide for Business Projectors

5 of 28

3.Applicable Models

EMP-600/800/810/811/820,30/52,720/730/520,73/53/74/54,735,8300/9300,7800/7850,S1/S1H,61/81,830/835,740/745/732/

737,821/828,7900/7950,S3/S4,765/760,755/750,62/82/X3,1715/1710/1705/1700,6000/6100,1815/1810,S5/X5/83/822,260/280/

6110/6010,400W/410W,83+/822+, 1825, EX90, G5350/G5300/G5150/G5100/G5200W/G5000, S6/X6/W6, 1735W/1730W/1725/

1720,

Z8000WU/Z8050W

4.Projector state and commands

4.1.Standby state (operation indicator is in orange)

When a projector is in a standby state, executable commands depend on projector models and standby configuration (network on, network

off). Refer to the following table.

(note1) EMP-61/81/830/835/740/745/821/828 returns "ERR" when it received commands other than PWR ON, PWR? , LAMP? and NULL

commands.

(note2) EMP-7800/7850 returns "ERR" when it received commands other than PWR ON, PWR? , SOURCE? and NULL commands.

(note3) EMP-8300/9300 returns "ERR" when it received commands other than PWR ON, SOURCE xx, PWR? , SOURCE? And NULL

commands.

All projectors returns "ERR" when the command format is not good.

All projectors returns "ERR" when the projector is not ready to reply the command.

Null command is command name for "ENTER" or "RETURN" key of the keyboard

The reply is ":"

Models Configuration Executable Commands

61/81

830/835

740/745/732/737

821/828

S3/S4

765/760/755/750

62/82/X3(76)

6100/6000

1715/1710/1705/1700

1815/1810/1825

S5/X5/83/822/83+/822+/EX90

260/280

6110/6010

400W/410W

G5350/G5300/G5150/G5100/

G5200W/G5000

S6/X6/W6

1735W/1730W1725/1720

84/85/824/825/826W

Z8000WU/Z8050W

network on/off PWR ON , PWR? , LAMP?

7800/7850/

8300/9300

7900/7950

(note3)

network on PWR ON , PWR? , SOURCE? , Null

command (note1)

network off PWR ON (note2)

Others -

Models Power Consumption

Network off Network on

78007850

7900/7950 about 1.5W about 47W

8300/9300 about 1.5W about 60W

8300+ELPXP01 about 1.5W about 60W

830/835 about 1.0W about 38W

740/745

732/737

760/765

750/755

about 4.0W about 35W

(only 745/737/765/755)

61/81,821/828 about 5.0W about 35W

ESC/VP21 Command User's Guide for Business Projectors

6 of 28

4.2.Power on state (operation indicator is in green)

All commands are executable.

5.Error Status

A projector returns the error status when a projector receives "ERR?" command.

The following projectors can return the error status while the projectors become the cool-downs status at an error and the projectors become

the error status after cooling down.

EMP-1700/1705/1710/1715, 6000/6100/6110/6010, 1815/1810/1825, S5/X5/83/822, 260/280, 400W/410W

EB-G5000/G5100/G5150/G5200W/G5300/G5350

And later models.

[The other models except the above models]

The models except the above models can return the error status while the projectors become the cool-downs status at an error.

The following table shows the return codes and the meaning of error status.

62/82

X3(76) about 4.0W

about 5.0W: 230V area about 25W

about 23W: 120V area

(only 62/82)

6100/6000 about 0.4W about 10W

1715/1705 about 3.8W about 18W

1815/1810/1825 about 2.6W about 12W

S5/X5/83/822/83+/822+/EX90 about 4.1W about 5W

(only 83/822)

260/280 about 4.1W about 4.1W

(only 280)

6110/6010 about 0.4W about 10.4W

400W/410W about 4.2W about 4.9W

G5350/G5300/G5150/G5100/

G5200W/G5000 about 0.4W about 10W

S6/X6/W6 about 3W -

1735W/1730W/1725/1720 about 4.0W about 9.0W

84/85/824/825/826W about 5.0W about 12W

Z8000WU/Z8050W TBD TBD

Command Returne code

ERR?

00 :There is no error or the error is recovered

01 : Fan error

03 : Lamp failure at power on

04 : High internal temperature error

06 : Lamp error

07 : Open Lamp cover door error

08 : Cinema filter error

09 : Electric dual-layered capacitor is disconnected

0A : Auto iris error

0B : Subsystem Error

0C : Low air flow error

0D : Air filter air flow sensor error

0E : Power supply unit error (Ballast)

0F : Shuter error

10 : Cooling system error (peltiert element)

11 : Cooling system error (Pump)

Models Power Consumption

Network off Network on

ESC/VP21 Command User's Guide for Business Projectors

7 of 28

6.Command transmission timing

6.1.Standby state

1) For all model with the standby configuration of "network on"

The first command can be sent anytime and the subsequent commands should be sent after receiving a colon from the projector.

2) Other than 1)

PWR ON can be sent any time.

6.2.Power-on state

A command should be sent after receiving the colon of the previous command from the projector. The following is an exception. When the

PWR OFF command is sent to 7800/7850/8300/9300 with the standby configuration of “network off”, the subsequent command should be

sent 10 seconds after the colon is received.

In case that you can not wait for the colon and send a command after receiving it, instead send a command after the execution time listed in the

following table.

(note1) When a projector receives the PWR ON command, it tries to ignite the lamp by activating the ballast unit. In case that the lamp fails to

be ignited, it tries to ignite the lamp three times at maximum.

When the lamp fails to be ignited three times, it is a lamp failure.

The projector returns a colon within 40, 70 and 100 seconds when successful in the first, second and third times respectively.

(note2) When the input video sync signal is stable, a colon is returned within 5 seconds. However, it may take more than 5 seconds when the

input video sync signal is unstable.

(note3) Projector initiates the process of the input video signal recognition when it receives a SOURCE command. If the signal of the video

input is changing (for example, from SVGA to XGA by A/V controller) during the process of the input video signal recognition, the

projector returns “ERR”.

(note 4) Projectors execute the PWR OFF command after they start completely.

(note 5) Projectors might return "ERR" when "Quick Setup" and "Auto Focus" functions are set to ON.

Command Models Execution time

PWR ON - 40 seconds (note 1)

830/835 (note 5)

7900/7950/740/745 20 seconds

61/81/821/828/S3/S4 25 seconds

PWR OFF (note 4) 600/800/810/811/820 130 seconds

All others 50 seconds

830/835 10 seconds

740/745

821

732/737

20 seconds

S3/S4

765/760

755/750

62/82/X3(76)

6100/6000

1715/1710/1705/172

1815/1810/1825

S5/X5/83/822/83+/822+/EX90

260/280

6110/6010

400W/410W

G5350/G5300/G5150/G5100/

G5200W/G5000

S6/X6/W6

1735W/1730W/1725/1720

84/85/824/825/826W

Z8000WU/Z8050W

5 seconds

SOURCE (note3) - 5 seconds (note 2)

All others - 3 seconds

ESC/VP21 Command User's Guide for Business Projectors

8 of 28

6.3.Warning and abnormal cases

Projector executes commands normally while a warning indicator such as a high temperature warning is on.

Projector does not execute commands nor return a colon when the projector is in an abnormal state such as a lamp failure and abnormal high

temperature.

As for EMP-6100/6000, EMP-1715/1710/1705/1700, EMP-1815/1810, EMP-S5/X5/83/822 and the following models, when an abnormal

state is continued for 130 seconds after, PWR ON command　becomes possible.

ESC/VP21 Command User's Guide for Business Projectors

9 of 28

7.Command list and Applicable Models

7.1.Command table 1 ( Fixed parameter)

(OSupported -Not supported)

Function Command 600/800/

810/811/

820 720/730/

520/735 30/52 73/53

74/54 8300/

9300

7800/

7850/

7900/

7950 S1/S1H 61/81 830/835

Power control PWR OOOOOOOOO

Input source SOURCE OOOOOOOOO

PinP setting PINP O---OO--O

A/V Mute Screen MSEL OOOOOOOOO

Auto Keystone AUTOKEYSTONE -O-O-O-OO

Aspect setting ASPECT - - - OOOO - O

Color Mode CMODE OOOOOOOOO

Lamp hour LAMP? OOOOOOOOO

Brightness level LUMINANCE - - - OOO - OO

A/V Mute MUTE OOOOOOOOO

Freeze FREEZE - OOOOOOOO

Rear Projection HREVERSE OOOOOOOOO

Ceiling VREVERSE OOOOOOOOO

Audio Input AUDIO O-OO-O---

Key operation KEY OOOOOOOOO

Function Command

740/745

732/

737765/

760

755/750

821/828 S3/X3/

S4 62/82 6100/

6000

1715/

1710/

1705/

1700

1815/

1810/

1825

S5/X5/

83/822/

83+/

822+/

EX90

260/280

Power control PWR OOOOOOOOO

Input source SOURCE OOOOOOOOO

PinP setting PINP ---------

A/V Mute Screen MSEL OOOOOOOOO

Auto Keystone AUTOKEYSTONE OO-O---O

(no S5) O

(no 260)

Aspect setting ASPECT O - OOOOOOO

Color Mode CMODE OOOOOOOOO

Lamp hour LAMP? OOOOOOOOO

Brightness level LUMINANCE OOOOOOOOO

A/V Mute MUTE OOOOOOOOO

Freeze FREEZE OOOOOOOOO

Rear Projection HREVERSE OOOOOOOOO

Ceiling VREVERSE OOOOOOOOO

Audio Input AUDIO ----O

-----

Key operation KEY OOOOOOOOO

Closed Caption CCAP ----O----

Air Filter Alarm Timer FLWARNING ----O----

Air Filter Timer FILTIME ----O----

Air Filter Usage Time FILTER ----O----

ESC/VP21 Command User's Guide for Business Projectors

10 of 28

Function Command 6110/

6010 400W/

410W

G5350/

G5300/

G5150/

G5100/

G5200W/

G5000

S6/X6/

1735W/

1730W/

1725/

1720

84/85/

824/825/

826W Z8000WU

/Z8050W

Power control PWR OOOOOOO

Input source SOURCE OOOOOOO

PinP setting PINP -------

A/V Mute Screen MSEL OOOOOOO

Auto Keystone AUTOKEYSTONE -------

Aspect setting ASPECT OOOOOOO

Color Mode CMODE OOOOOOO

Lamp hour LAMP? OOOOOOO

Brightness level LUMINANCE OOOOOOO

A/V Mute MUTE OOOOOOO

Freeze FREEZE OOOOOOO

Rear Projection HREVERSE OOOOOOO

Ceiling VREVERSE OOOOOOO

Audio Input AUDIO O

-------

Key operation KEY OOOOOOO

Closed Caption CCAP OOOOOOO

Air Filter Alarm Timer FLWARNING O------

Air Filter Timer FILTIME O------

Air Filter Usage Time FILTER O------

Otros manuales para ESC

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Proyector de Epson

Epson

Epson EX7220 Manual de usuario

Epson

Epson EH-LS800W Manual de usuario

Epson

Epson 7800p - PowerLite XGA LCD Projector Hoja de especificaciones

Epson

Epson EMP-TS10 Manual de usuario

Epson

Epson BrightLink 455Wi Manual de usuario

Epson

Epson HA35A Manual de usuario

Epson

Epson EH-TW5200 Manual de usuario

Epson

Epson EB-W8 Manual de usuario

Epson

Epson EB-L200X Manual de usuario

Epson

Epson PowerLite D6150 Guía de referencia

Epson

Epson PowerLite Pro Z8455WUNL Instrucciones de funcionamiento y seguridad

Epson

Epson PowerLite 4100 Manual de usuario

Epson

Epson EMP-7550 - XGA LCD Projector Manual de usuario

Epson

Epson Pro L20000UNL Manual de usuario

Epson

Epson EB-L1105U Manual de usuario

Epson

Epson EH-TW8000 Manual de usuario

Epson

Epson dreamio EMP-TW980 Manual de usuario

Epson

Epson PowerLite 107 Manual de usuario

Epson

Epson brightlink Manual de usuario

Epson

Epson EX3200 Guía de referencia

Epson

Epson EMP-821 Manual de usuario

Epson

Epson EB-1400Wi Manual de usuario

Epson

Epson EMP-505 / 715 Manual de usuario

Epson

Epson EB-Z8050W Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Christie

Christie LHD700 Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario

Asus

Asus ZenBeam Latte Manual de usuario

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Manual de usuario

JVC

JVC 1108TTH-AO-AO Manual de usuario