Epson EasyFlow WorkForce 30 Manual de usuario

R-3_19,Feb’10-jcr ARTAINIUM EASYFLOW BULK INK SYSTEM FOR EPSON WF 30 QSG — Page 1of 2

EasyFlow®BULK INK SYSTEM Quick Start Guide

EPSON WorkForce 30

BEFORE YOU BEGIN...

Before you install the ArTainium EasyFlow Bulk Ink System, you should setup the Epson printer with the Epson supplied inks

and driver. This will allow you to conduct a nozzle check to ensure the printer is working properly. Record the alpha-numeric

value from the nozzle check (located on the far right side of the page). This is your Firmware Number which will be needed

during the ArTainium ICC Proﬁle Registration. Once completed, you can begin the bulk ink system installation process.

Note: Please remove the Epson cartridges before proceeding to step 1.)

NOTE: Quick Start Guide for WorkForce 30 only

1. Ink Box with Ink Multi-Cartridge &Tubes

2. Large Tube Support (WF 1100 only).

3. (3)Plastic Dividers

7. Rubber Gloves.

8. (4) Syringes and Alcohol Prep for Priming.

9. Plastic Arm (WF 30 only)

4. Small Tube Support (WF 1100 only).

5. (4) Individual Ink Bags.

6. (2) Lid Holders (WF 1100 only).

Check to ensure you have all components shown in the pictures:

Epson WorkForce 30 Printer ArTainium EasyFlow Bulk Ink System Contents

1.) Before installing the ink bag, check that the ink bag valve

is perpendicular to the ink tube as shown in the picture.

Next, remove plastic cap from the ink bag valve.

2.) Match each ink bag with the appropriate color bead found in the ink box. Fasten the ink bag valve with the ink box connector

by pushing the connections together and twisting the cap to lock them into place. Once the ink bag has been installed, turn the

ink bag valve parallel to the ink tube. Finally, insert the dividers between each bag.

3.) Place the bulk ink dampers face down on top of the bulk ink box. Use care to avoid damaging the bulk ink dampers reset button. Notice how the reset button is not making contact with the bulk

ink box. With the syringe plunger pressed down, insert the syringe tip into the septum of the damper. Next, slowly extract the plunger. Ink will start to ﬂow through the tubing and into the damper.

Remove the syringe from the septum when a small amount of ink has ﬁlled the syringe tip. Repeat the process for the remaining four channels.

4.) Lift the lid and power on the printer. 5.) Once the printer has completed initializing, press the ink

out button.

6.) Raise the lid of the ink cartridge bay. Firmly grasp the lid

and twist it sideways until it becomes dislodged. The lid

will not be needed for proper functioning of the printer with

either the bulk ink system or individual ink cartridges.

EasyFlow®BULK INK SYSTEM: WF 30 Installation Instructions: Setup

Bulk ink dampers

Reset Button

ARTAINIUM EASYFLOW BULK INK SYSTEM FOR EPSON WF 30 QSG — Page 2of 2

ink. differently.®, ArTainium® UV+ & EasyFlow® are Registered Trademarks, and Sawgrass Technologies™ is a Trademark of Sawgrass Technologies, Inc. Epson Stylus® is a Registered Trademark of Epson Seiko Corporation.

•Make sure you install, register and conﬁgure the ArTainium ICC Proﬁle.

• Perform a Nozzle Check from the Epson Driver. A few cleaning cycles may be necessary to get a good Nozzle Check.

•There may be small pockets of air in the lines after setup. If so, these will clear after a few prints are run.

•If the System is to be dormant for several days, use the Tube Clamps to seal the lines at the Reservoir Box.

• Do not raise the ink box higher than the printer.

Congratulations! You have successfully installed the ArTainium EasyFlow®Bulk Ink

System. Be sure the printer is placed on a level surface next to the ink box.

Caution: The ink box should never be raised higher than the printer as this will cause ink to

leak into, and damage the printer.

7.) The ink cartridge bay should look like the picture above

after removing the ink cartridge cover.

8.) Gently insert the ink dampers into the cartridge bay.

Use care to avoid damaging the bulk ink dampers reset

button. The black dampers should be positioned on the

far left side and the yellow on the far right.

9.) Firmly push the bulk ink dampers into place. You should

hear a slight clicking sound when the dampers become

engaged. Again, please use care to avoid damaging the

bulk ink dampers reset button.

11.) The plastic arm should be aligned so that the edge of

the adhesive Velcro is situated at the upper top right

hand corner of the ink cartridge bay. Press the plastic

arm ﬁrmly to set the adhesive Velcro in place.

10.) Remove the backing from the plastic support arm.

13.) Press the ink out button to begin the cartridge

recognition cycle. Once the cycle is complete, the Ink

Out light should turn off. If the light does not turn off,

follow the Chip Reset Instructions to remedy. Also,

check that the dampers have been inserted ﬁrmly in

place.

12.) Align velcro strips on the tubing with the velcro strips

on the arm.

NOTE: Be sure to align the left edge of the tape with the left

edge of the arm. This is to eliminate the possibility

of too much or too little slack in the tubing.

EasyFlow®BULK INK SYSTEM Quick Start Guide: WF 30 (Continued...)

Otros manuales de Impresora de Epson

Epson

Epson Stylus SX130 series Manual de usuario

Epson

Epson Stylus C43 Series Manual de operación y mantenimiento

Epson

Epson 4000 - Stylus Pro Color Inkjet Printer Manual de funcionamiento

Epson

Epson R1900 - Stylus Photo Color Inkjet Printer Manual de usuario

Epson

Epson LQ-2180 Guía del usuario

Epson

Epson WorkForce Pro WF-M5190DW Manual de usuario

Epson

Epson Stylus Color 660 Manual de usuario

Epson

Epson ColorWorks CW-C6000 Series Manual de usuario

Epson

Epson XP-850 Manual de usuario

Epson

Epson C31CA26031 - TM C3400 SecurColor Color Inkjet... Manual de uso y cuidado

Epson

Epson WorkForce Pro WP-M4525 Manual de usuario

Epson

Epson U230 - TM Two-color Dot-matrix Printer Manual de instrucciones

Epson

Epson SC-P800 Series Manual de usuario

Epson

Epson L1300 Manual de instrucciones

Epson

Epson 1280 - Stylus Photo Color Inkjet Printer Manual de usuario

Epson

Epson Stylus Color 440 Manual

Epson

Epson U375 - TM B/W Dot-matrix Printer Manual de usuario

Epson

Epson ET-5880 Manual de instrucciones

Epson

Epson U220B - TM Two-color Dot-matrix Printer Manual de uso y cuidado

Epson

Epson Stylus CX4900 Series Manual de usuario

Epson

Epson Artisan 1430 Manual de usuario

Epson

Epson R2880 - Stylus Photo Color Inkjet Printer Manual de usuario

Epson

Epson WF-C878R Series Manual de usuario

Epson

Epson EPL-7500 Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario

IRA3D

IRA3D POETRY4 Manual de usuario

Ricoh

Ricoh Aficio AP400 Manual de usuario

BIXOLON

BIXOLON SRP-352plusV Manual de usuario