EPOX KP6-LS Manual de usuario

TRADEMARK

All products and company names are trademarks or

registered trademarks of their respective holders.

These specifications are subject to change without

notice.

Manual Revision 1.2

February 10, 1997

KP6-LS (SMP)

A Dual Pentium®II Processor based

AGPmotherboard

FeaturesKP6-LS

Page 2

FEATURES

KP6-LS Features:

•KP6-LS is based on the Dual Pentium®II Processor operating at 233 ~ 330

MHz on Slot 1. The board is configured by an Easy-Setting-Single-Jumper

(E.S.S.J.) to match your CPU clock speed.

•Designed with Intel’s 82443 LX AGPset.

•Supports up to 1 Gigabyte of DRAM (minimum of 8 MB) on board, You can

use 168-pin DIMM x 4. It will automatically detect Extended Data Output

(EDO) DRAM or Synchronous DRAM memory (SDRAM)

•KP6-LS will support Error Checking and Correcting (ECC) when using parity

DRAM memory modules. This will detect multiple bit errors and correct 1-bit

memory errors.

•Supports (3) 16 bit ISA slots, (4) 32 bit PCI slots, (1) AGP slot and provides

(2) independent high performance PCI IDE interfaces capable of supporting

PIO Mode 3/4 and Ultra DMA 33 devices. The KP6-LS supports (4) PCI

Bus Master slots and a jumperless PCI INT# control scheme which reduces

configuration confusion when plugging in PCI card(s).

•Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary IDE

interfaces.

•Designed with Winbond W83977 Multi I/O: (1) floppy port, (1) parallel port

(EPP, ECP), and (2) serial ports (16550 Fast UART), (1) IrDA.

Note: Japanese “Floppy 3 mode” is also supported

•Includes a PS/2 mouse connector.

•Allows use of a PS/2 or AT keyboard.

•Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.2themax.com/

please visit our Technical Support section for the latest updates)

FeaturesKP6-LS

Page 3

•KP6-LS utilizes a Lithium battery which provides environmental protection and

longer battery life.

•Supports the Universal Serial Bus (USB) connector. The onboard PIIX4 chip

provides the means for connecting PC peripherals such as; keyboards,

joysticks, telephones, and modems.

•Built-in ATX 20-pin power supply connector.

•Software power-down when using Windows®95.

•Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely.

•Supports Wake On-LAN (WOL).

•Resume by Alarm - Allows your system to turn on at a preselected time.

•Power Loss Recovery - In the event of a power outage your system will

automatically turn itself back on without user intervention.

•Supports CPU Hardware sleep and SMM (System Management Mode).

•Supports Desktop Management Interface (DMI) facilitating the management

of desktop computers, hardware and software components and peripherals,

whether they are stand-alone systems or linked into networks. (option)

Installation KP6-LS

Page 4

Infrared

J1 Chassis

Intrusion

JP3

Clear

CMOS

Secondary IDE

Primary IDE

J11

J12

FDD Connector

J13

PCI Slot #1

AGP SLOT

CPU Cartridge SLOT 1

PCI Slot #2

PCI Slot #3

PCI Slot #4

ISA Slot #1

ISA Slot #2

ISA Slot #3

Intel

443LX

PCIset

COM 1COM 2

USB 1

(Top)

Mouse

(Top)

USB 0

(Bottom)

PS/2 Keyboard

(Bottom)

KP6-LS

Rev. #

USB

Parallel Port

Primary

ATX Power Input

Battery

Flash Memory

for BIOS

200M H z

266M H z

300M H z

330M H z

233M H z Default

JP7

DIMM 2

DIMM 1 Bank 0

Bank 1

DIMM 3 Bank 2

J14

Intel

PIIX4

PCIset

Chassis

Fan

CPU1

Fan

LM79

Hardware

Monitor

Winbond

83977

I/Oset

JP1

JPX1 Wake On-Lan

Intel

82093A

DIMM 4 Bank 3

CPU Cartridge SLOT 1

Secondary

CPU2

Fan

Figure 1

KP6-LS Detailed Layout

InstallationKP6-LS

Page 5

Easy Installation Procedure

The following must be completed before powering on your new system:

Configure Jumpers to match your hardware

Install memory chips

Device Connectors

Configure Jumpers

2theMax designs all motherboards with the fewest jumpers to make your install fast

and easy.

The following will describe all of the jumpers that you are required to set before

moving on to step 2.

Note: The jumpers as depicted as shown (Figure 1) in their correct physical

orientation.

CMOS Clear

JP3: = 1-2 - Run Mode (Default)

= 2-3 - Clear CMOS

JP3:1

BIOS Voltage Setting

JP1: = 1-2 - +5V Flash (Default)

4-5

= 2-3 - +12V Flash

5-6

JP1:6

Installation KP6-LS

Page 6

CPU Processor Selection

JP7: = 1-2 - 200MHz

= 3-4 - 233MHz (Default)

= 5-6 - 266MHz

= 7-8 - 300MHz

= 9-10 - 330MHz

= 11-12 - Reserved

= 13-14 - Reserved

= 15-16 - Disable E.S.S.J.

JP7:

JP9:

JP10:

JP11:

JP12:

Reserved CPU Processor Selections

JP9: = Reserved

JP10: = Reserved

JP11: = Reserved

JP12: = Reserved

1516

InstallationKP6-LS

Page 7

System Memory Configuration

Memory Layout

The KP6-LS supports (4) 168-pin DIMMs (Dual In-line Memory Module). The

DIMMs can be either EDO (Enhanced Data Out) or SDRAM (Synchronized

DRAM).

• DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or

120MHz (8ns) bus speed.

• If you use both 50ns and 60ns memory you must configure

your BIOS to read 60ns.

• When using Synchronous DRAM we recommend using the

4 clock variety over the 2 clock.

• Fast Page Mode DRAM (FPM) is not supported by the LX

AGPset. Only EDO and SDRAM are supported.

Figure 2 and Table 1 show several possible memory configurations.

* SDRAM only supports 8, 16, 32, 64, 128MB DIMM modules.

Table 1

yromeMlatoT 1MMID 2MMID 3MMID 4MMID

BG1= mumixaM

*MARDS/ODE BM23,BM61,BM8 M652,BM821,BM46 1X

*MARDS/ODE ,BM23,BM61,BM8 BM652,BM821,BM46 1X

BM867= mumixaM

*MARDS/ODE BM23,BM61,BM8 M652,BM821,BM46 1X

*MARDS/ODE ,BM23,BM61,BM8 BM652,BM821,BM46 1X

enoN

BM215= mumixaM

*MARDS/ODE ,BM23,BM61,BM8 BM652,BM821,BM46 1X

enoNenoN

BM652=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

BM652,BM821,BM46

enoNenoNenoN

InstallationKP6-LS

Page 8

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your connec-

tions (figure 12).

USB 1

(Top)

USB 0

(Bottom)

PS/2 Mouse

(Top)

PS/2 Keyboard

(Bottom)

Parallel Port

(Top)

Com1Com2

(Bottom Left)(Bottom

Right)

J1:Chassis open monitoring(Reserved)

• A plug-in to monitor the chassis

J3:Chassis Fan Power

• A plug-in for the chassis Fan Power

J4:Chassis Panel Connector

• Keylock, Speaker, Reset, Turbo, Sleep, G/LED and HDD LED

J5:Floppy Controller

J6:Primary IDE

J7:Secondary IDE

J8:CPU 2 Fan Power

• A plug-in for the Power supply so that BIOS can monitor the RPM’s

J12:ATX Power Connector

• 20-pin power connector

J13:CPU 1 Fan Power

• A plug-in for the CPU Fan Power

JPX1:•WakeOn-LAN (WOL)

Figure 12

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345

InstallationKP6-LS

Page 9

Power On/Off - This is connected to the power button on the case.

Using the Soft-Off by Pwr-BTTN feature, you can choose either Instant

Off (turns system off immediately), or 4 sec delay (you need to hold the

button down for 4 seconds before the system turns off). When the

system is in 4 sec delay mode, 2theMax has added a special feature to

make the system go into suspend mode when the button is pressed

momentarily.

J14

Device Connectors (continued)

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

Turbo LED indicator - LED ON when higher speed is selected

Sleep/Resume switch : Closed to enter sleep mode, a keystroke or

mouse movement will instantly "wake up" the system.

Power Saving LED indicator - LED ON when system is in any power

saving mode

IDE LED indicator - LED ON when Onboard PCI IDE Hard disks is

activate

KeyLock - Keyboard lock switch & Power LED connector

1. Power LED(+) 4. Keylock

2. N/C 5. GND

3. GND

Otros manuales para KP6-LS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de EPOX

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario