EOS VITAE Guía de instalación

Assembly instructions and

instructions for use

Infrarot-Strahler VITAE

DruckNr.29342328en/ 33.06

Importantnotice

There is a fire risk if assembled incorrectly.

Pleasereadtheseassemblyinstructionscarefully.

Take special note of the measurement details

and the following notes.

lThe infrared thermal emitter is intended for a

connectionvoltageof230V50Hzvia aninfrared

controller.

lAssemblyandconnectiontotheinfraredcontroller

must be carried out in accordance with the

connectiondiagram(Fig.11).

lBefore the emitter is operated via the controller,

checkthatallconnectorsarefirmlyconnectedwith

no risk of coming loose.

lTheEU60335-2-53(VDE 0700Part53)regulations

aretobecomplied with inside the infraredbooth.

lIOnlythenumberofemittersspecifiedforthesize

of the booth should be assembled in the infrared

thermalbooth.

lOne of the controllers specified below should be

usedtoregulateorcontroltheinfraredemitter. This

controller should be fixed to the infrared thermal

boothinaccordancewiththeassemblyinstructions.

lAttention: Covering the infrared thermal

emitter causes a fire risk!

lThe assembly of the infrared emitter in the booth

mustbe carried out in sucha way to assure even

all-roundemissionforthesaunafrequenter.

lTheinfraredthermalemitterisnotsuitableassembly

on the booth ceiling and must not be mounted

there.

lIfthe infrared thermal emitteris assembled in the

rear area, then appropriate protective measures

mustbetakentoensurethattheflockedprotection

grille cannot be pressed in unintentionally (e.g. a

woodengrillemountedinfront).

lTakecaretoensurethatthemainenergydischarge

occursthroughtheinfraredradiation.

Additionally, however, a thermal heat discharge

arisesatthehousingintheverticalassembly. This

heat can stress the emitter thermally! Caution:

firerisk!

Ensurethatthishotconvection aircanescapeby

risingfreely.

If necessary, appropriate steps should be taken

(e.g. thermal protection slabs) to ensure that the

woodisnotexposedtoinadmissibletemperatures.

MADE IN GERMANY

Technical data

Voltage: 230 V 50 Hz

Weight: approx. 2 kg

Power Vitae 350 W, Art.-Nr. 94.2865

input: Vitae 500 W, Art.-Nr. 94.2576

Vitae 750 W, Art.-Nr. 94.2577

emission area: 1,4 mm - 10 mm

measures HWD: 870 x 184 x 65 mm

frontsight cutout of the wall

165

890

184

870

english

Abb. 1

mind.15 cm

mind. 9 cm

IR-Strahler

Vitae

mind. 50 cm

mind. 7 cm

lThe infrared thermal emitter is equipped with a

silicon connection cable with a 3-pin connector.

This connector is joined to the connector of the

infraredcontrollerwithafreeoutlet.

Care must be taken to ensure that the earth is

properly tight.

lUpto5infraredthermalemittersmaybeconnected

to this socket distribution.

For practical reasons, the connector should be

fitted to the booth ceiling.

lTake care to ensure that the special ceramic

emitter is not subject to any mechanical

stresses(knocks,pressure). Riskofbreakage.

Althoughbreakageisunlikelyifitisusedproperly,

iftheceramicemittershouldbreak,replaceitwith

anew one.

lrecommendeddistanceis50cmbetweenhuman

andIR-emitter.

Assembly

Caution!

Remove the transport stabilisers from the Vitae-

emitter, loosening the covering grille. Remove the

foamedpad. Take care that theVitae-emitter does

notbedemaged.

Fig. 2

Fig. 3

Theemitter should beassembled in sucha way as

to ensure that the body of the sauna frequenter

radiatesoveraslargean area as possible.

Assemblyinthefourcornersoftheinfraredboothis

recommended.

Attention!

Ifthereisanyskindeseaseorillness,youshould

ask a doctor before using.

Assembly example:

Fig 4

Remove the protect

cushion

english

Fig. 5

Mounting example in the sauna cabin with

additional upper bench.

min. 7 cmmin. 9 cm

IR-emitter

Vitae

min. 15 cm

min. 9 cm

min.7 cm

at least 9 cm

with additional

upper seat

160

171

eventuell Holzleiste

Holzschutz

itter

50 15 40

Gerät muss

hinterlüftet sein

Electrical connection

infrared

emitter

Socket

distribution

Supply lead

controller

Fig. 11

lMinimumdistances

Theminimumdistancefromtheemitterupperedgeto

the booth ceiling must be 7 cm.

Theminimumdistancefromtheemitterloweredgeto

thewooden floor of the boothmust be 9 cm

Thehorizontalminimumdistancebetweentheemitter

and all combustible parts must be 4 cm.

Very important!

Inthecaseofverticalassembly(connection

always upwards or in accordance with the

booth manufacturer's specifications), the

areaabovetheemittershouldnotbeencased

withwoodinfront(Fig.9). Hotairrisingwhen

the housing is heating must be able to

escape freely. Fire risk!

In the case of horizontal assembly in the

area of the nets (net emitter), the emitter

may not be covered by objects such as

towels,andmustbemadesafeifnecessary

by fitting an additional wooden grille. Fire

risk!

Positioning of the infrared emitters

Fig. 7

Fig. 8

Fig. 9

Area above emitter must

ensure free air convection

Horizontal assembly

Fig. 10

Caution!

Forassemblyofthenetemitter,themeasurements

specified in Fig. 4 must be complied with.

verticalassemblyon the booth wall

verticalassembly in the boothcorners

english

Fig. 6

For assembly, a right-angled opening of 890 x

165 mm must be fitted vertically into the wood.

must be fitted vertically into the wood.

Theemittercanthenbeassembledwiththeenclosed

chipboard screws (see Fig. 7 and 8).

Recommendeddistancebetweenhumanandemitter

is approx. 50 cm (see fig. 6).

Max.4piecesfor750Wperemitter(3500W)

wood protected grid

90 15

wood border perhaps

appliance should be

aerated in the back

Serviceaddress:

EOS-WerkeGüntherGmbH

Adolf-Weiß-Str.43

35759Driedorf-Germany

tel +49 (0) 2775 82 240

fax +49 (0) 2775 82 455

[email protected]

www.eos-werke.de

spectral achievement distribution TheIR-emitterisdesignedformountinginaIR-warm

cabin or sauna only. It just can be used with a

controller.Thewarrantyisnottoapplyforotheruse.

Guarantee

Theguaranteeistaken over according to thelegal

regulationsatpresent.

Manufacturer’swarrenty

- The period of warrenty starts from the date of

purchaseand lasts up to 2yearsfor commercial

useand 3 years for private use.

- Alwaysincludethecompletedwarrentycertificate

whenreturningequipment.

- Thewarrentyexpiresforapplianceswhichhave

been modified without manufacturer’s explicit

agreement.

- Damages caused by incorrect operation or

handlingthroughnon-authorizedpersonsarenot

coveredunderthetermsofwarranty.

- Intheeventofaclaim,pleaseindicatetheserial

number as well as the article code number and

type name with expressive description of the

fault.

- Thiswarrentycoversdamagedpartsbutnodefects

duetowearandtear.

Incaseofcomplaintpleasereturntheequipmentin

its original packaging or other suitable packaging

(caution:dangeroftransportdamage)toourservice

department.

Always include the completed warrenty certificate

whenreturningequipment.

Possibleshippingcostsarisingfromthetransportto

and from point of repair cannot be borne by us.

OutsideofGermanypleasecontactyourspecialist

dealer in case of warranty claims. Direct warranty

processing with our service department is in this

case not possible.

Equipmentstart-update:

Stampandsignatureoftheauthorizedelectrician:

Fig. 12

Fig. 13

Fig. 14

Fig. 15

Irradiancy

For a too long time looking in the

emitter,youreyescanbedemaged.

english

spectral achievement distribution

Vitae lamp

Sun

Irradiancy

Vitae lamp

Sun

Otros manuales para VITAE

Tabla de contenidos

Otros manuales de Calentador de EOS

EOS

EOS Herkules XL S120 Manual de usuario

EOS

EOS Majesty Manual de usuario

EOS

EOS Mega S HD Manual de usuario

EOS

EOS Zeus HD Manual de usuario

EOS

EOS Gracil Series Manual de usuario

EOS

EOS Herkules XL S120 Manual de usuario

EOS

EOS Mythos S35 Guía del usuario

EOS

EOS Structure Manual de usuario

EOS

EOS 43.HB Guía de planificación

EOS

EOS Zeus S Manual de usuario

EOS

EOS Vitae protect Guía de planificación

EOS

EOS Saunadome II Manual de usuario

EOS

EOS VITAE Guía de planificación

EOS

EOS Mythos S34 Manual de usuario

EOS

EOS Thermo-Tec S Guía de planificación

EOS

EOS Zeus Manual de usuario

EOS

EOS Future Manual de usuario

EOS

EOS M3 Guía de planificación

EOS

EOS IRS 40 RHK Guía de planificación

EOS

EOS EOS Selection Manual de usuario

EOS

EOS MEGA 720 Manual de usuario

EOS

EOS IRS 35 RHK Guía de planificación

EOS

EOS Goliath HD Manual de usuario

EOS

EOS Bi-O Mat W Guía de planificación

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario