Enttec Hyperion Manual de usuario
Hyperion User Manual
51164
For latest version visit:
www.enttec.com
November 17 ID: 3809208 1
Hyperion
INTELLIGENT GIGABIT SWITCH
Contents
Package Contents....................................................................2
Safety Information ..................................................................2
Physical Dimensions...............................................................3
Specifications...........................................................................4
Hyperion Hardware Interface...............................................4
Application Diagram ...............................................................6
Ethernet Link Pin Out .............................................................6
Redundancy Link .....................................................................7
Initial Setup...............................................................................2
Out of Box (Factory Settings)............................................2
Change Device IP.................................................................2
Default Login Details..........................................................2
How to Access Web Interface?..............................................8
Hyperion Web Interface.........................................................9
Home Page ................................................................................9
Settings Page..........................................................................10
Change Password ..............................................................10
Ports Page................................................................................ 11
Administration........................................................................12
Backup..................................................................................13
Restore.................................................................................13
Restore to factory defaults (web interface) ...............12
Restore to factory defaults (reset switch) ..................13
Firmware Update...............................................................13
Ordering Information............................................................15
Hyperion User Manual
51164
For latest version visit:
www.enttec.com
November 17 ID: 3809208 2
Package Contents
•Hyperion (71025, 71026 0r 71027)
•2m cat5 cable (79102)
•This user manual
Safety Information
•This unit is intended for indoor use only
•Do not expose this device to rain or moisture,
doing this will void the warranty
•Make all the connections before you plug in the
mains power
•Do not remove the cover, there are no user
serviceable components inside
•Never plug this unit in to a dimmer pack
•Ensure proper earth connections
•Always be sure to mount this unit in an area that
will allow proper ventilation. Allow about 6” (20
cm) between this device and a wall
•Power-supply cords should be routed so that
they are not likely to be walked on or pinched
Initial Setup
Out of Box (Factory Settings)
All Hyperion devices come with the following
default settings:
•IP: 192.168.0.10
•Subnet Mask: 255.255.255.0
•Gateway: 0.0.0.0
Change Device IP
To change the IP of the device do as follows:
•Connect Hyperion directly to a computer
using a cat5 cable
NOTE
The computer should have the following network
adapter settings:
•Static IP: 192.168.0.1
•Subnet Mask: 255.0.0.0
•Gateway: 0.0.0.0
•Type in the default IP of 192.168.0.10 into any
browser
•Log into the device as shown in window
below:
Default Login Details
The log in details for the device are as follows:
•Username: admin
•No password required
Once logged in, set the device with the
appropriate network configurations
Hyperion User Manual
51164
For latest version visit:
www.enttec.com
November 17 ID: 3809208 3
.
Physical Dimensions
Hyperion User Manual
51164
For latest version visit:
www.enttec.com
November 17 ID: 3809208 4
Specifications
Item
Model SKU
71025
71026
71027
Input Voltage
90-264 V AC
Input Frequency
47-63 Hz
Temperature
Storage
-20°C ~ 70 °C
Working
0°C ~ 40 °C
Humidity
Storage
5% ~ 90% non-condensing
Working
10% ~ 90% non-condensing
Connectors
1X powerCON IN
6X Front etherCON connectors
2X Rear etherCON connectors
1X 1000M SFP port
1X
OpticalCON
(Front)
N/A
1X OpticalCON
(Rear)
IP Rating
IP20
Cooling Method
Fan (always on)
Maximum Power
60 W
Power Supply
Protection
Over-current
Auto recovery
Over-temperature
Latch
Short
Auto recovery
Over-voltage
Auto recovery
MAC Address
table limit
8192
Maximum frame
length
9216 B
Cache
32 Mb
Switching
Capacity
52 Gbps
IGMP support
Yes (V1/V2)
IGMP snooping
(multicast)
Yes, enabled by default
Net Weight
2.5 kg / 5.52 lb
Gross Weight
2.8 kg / 6.18 lb
Dimensions
(without ears)
L x W x H
445.82 mm x 180.29 mm x 43.20 mm
17.55 in x 7.10 in x 1.70 in
Dimensions (with
ears)
L x W x H
483 mm x 180.29 mm x 43.20 mm
19.02 in x 7.10 in x 1.70 in
Packaging
Dimensions
533 mm x 247 mm x 111 mm
21.78 in x 9.72 in x 4.37 in
Ethernet
Compliance
IEEE 802.3, IEEE 802.3u, IEEE 802.3x
Flow Control, IEEE 802.3ab Gigabit
Ethernet
Due to continuous improvements and innovations of all
ENTTEC products, specifications and features are
subject to change without notice.
Hyperion Hardware Interface (Front)
Hyperion User Manual
51164
For latest version visit:
www.enttec.com
November 17 ID: 3809208 5
LED Status
Power LED
Status LED
Operation
Green (static)
Amber
Device loading firmware
Green (Static)
Green (Blinking)
Normal operation
Green (Static)
No lit
Rebooting
Hyperion Hardware Interface (Rear)
Hyperion User Manual
51164
For latest version visit:
www.enttec.com
November 17 ID: 3809208 6
Application Diagram
Ethernet Link Pin Out
Pin
Colour
1
White/Orange
2
Orange
3
White/Green
4
Blue
5
White/Blue
6
Green
7
White/Brown
8
Brown
Hyperion User Manual
51164
For latest version visit:
www.enttec.com
November 17 ID: 3809208 7
Redundancy Link
Redundancy link is the ability of both port 7 and port 8 of Hyperion to be connected to the same networking
device. This ensures that the network connection is maintained in case of failure of one of the two links.
Note:
•Ensure the networking device e.g. router or switch connected using the redundancy links is capable of
such a connection
•Redundancy link should be enabled prior to connecting two switches using port 7 and port 8
•Once the device is set to factory defaults using the button, the redundancy link is disabled
•To enable the redundancy link reload/refresh the device web page
•If redundancy link is listed as disabled on the web interface reload page
Hyperion User Manual
51164
For latest version visit:
www.enttec.com
November 17 ID: 3809208 8
How to Access Web Interface?
1. Open any modern web browser, such as Chrome, Firefox, Safari or Edge
2. To access the web interface type in the assigned IP address of Hyperion e.g: 10.10.0.201
3. You will be prompted to login using the following details:
•User name: admin
•Password:
Please use the password, if any set by you.
By default, password is not required, so should be empty.
Hyperion User Manual
51164
For latest version visit:
www.enttec.com
November 17 ID: 3809208 9
Hyperion Web Interface
The Hyperion web interface has the following sections:
1. Home
2. Settings
3. Ports
4. Administration
Home Page
Home page shows the followings information:
•Device Name – Identify switches in the
network
•System uptime - The time since the device
was switched on
•Number of ports
•Device IP address
•Sub netmask
•Gateway IP
•Mac address
•Redundancy link status
•Software version
•Firmware version
•Boot version
•Hardware version
Hyperion User Manual
51164
For latest version visit:
www.enttec.com
November 17 ID: 3809208 10
Settings Page
The setting pages enables the following:
•System name - Assign a device name
•System location – Location of switch
•System contact – Note network contact
•IP address – IP of device
•NetMask – netmask of device
•Default Gateway
•DNS 1/ DNS 2 – Configure IP of DNS server
to be used
•Security settings – change device password
Change Password
The change password feature is under the Settings
page as shown in screen below:
To change the password:
1. Enter the new password
2. Click Update Security Settings
Tabla de contenidos
Otros manuales de Cambiar de Enttec
