Entrotec PRO-AC4 Instrucciones de montaje
Legal
2
Legal and Copyright Notice
Entrotec regularly develop and enhance product lines, these changes will be included in the latest
documentation. Whilst every effort has been made to ensure the accuracy of the information
supplied herein, Entrotec is not responsible for any errors or omissions. Many of the images
shown are for illustration purpose only. The actual product may vary due to product enhancement
or custom configurations. The materials contained in this document are protected and may be
subject to intellectual property rights.
Copyright 2021 Entrotec Limited. All rights reserved.
Installation Specification
It is the responsibility of the installer to follow Entrotec’s installation and cable specification as well
as ALL relevant wiring regulations. Failure to comply with Entrotec’s installation and cable
specification may result in erratic operation of equipment and could invalidate any warranty.
Installations must comply with the following applicable standards:
•BS 7671: Requirements for electrical installations. IET Wiring Regulations 18th Edition.
•The Electricity at Work Regulations 1989
•ANSI/TIA-568.0-D: Generic Telecommunications Cabling for Customer Premises.
•ANSI/TIA-568.1-D: Commercial Building Telecommunications Cabling Standard.
IET Wiring Regulations 18th Edition: Regulation 444 (MEASURES AGAINST ELECTROMAGNETIC
DISTURBANCES) imposes requirements for segregation of circuits.
IET Wiring Regulations 18th Edition: Regulation 528 (PROXIMITY TO WIRING SYSTEMS TO OTHER
SERVICES) imposes requirements for segregation of door entry / access control circuits (Band I),
230VAC mains circuits (Band II) and other higher voltage circuits.
IET Wiring Regulations 18th Edition: Regulations 541 and 542 impose requirements for earthing
and bonding conductors. Ensure ALL metalwork is bonded to the buildings earth, this includes call
panels, exit switches, cabinets and metal conduit. Ring terminals and earth points are provided on
call panels and cabinets to terminate earth cables, ensure these connections are made.
WARNING - ISOLATION OF ELECTRICAL EQUIPMENT
In compliance with The Electricity at Work Regulations 1989, electrical equipment should be
made dead to prevent danger while work is carried out on or near that equipment. No person
shall be engaged in any work activity on or so near any live conductor.
Warranty and Support
Entrotec systems are renowned for their reliability and have a 2-year warranty on all Entrotec
manufactured products as standard. This warranty does not cover water damage, vandalism,
mains electrical faults, lightning strikes, damage caused by miswiring or cable faults.
Entrotec offer complimentary training courses and telephone support:
01506 886 235 - 8:30am to 5pm Mon-Thurs and 8:30am to 4pm Friday.
technicalsupport@entrotec.co.uk
Contents
3
Contents
1Cable Specification ............................................................................................................4
1.1 Typical Configuration ......................................................................................................4
2Overview...........................................................................................................................5
3Power Supply ....................................................................................................................6
3.1 Mains Supply Connections..............................................................................................6
4Access Controller...............................................................................................................7
4.1 Readers Connections ......................................................................................................9
5Lock Connections.............................................................................................................10
5.1 Lock Distribution Board ................................................................................................10
5.2 Exit Switch Connections................................................................................................10
5.3 Fail Open Lock Connection ...........................................................................................11
5.4 Fail Closed Lock Connection .........................................................................................11
5.5 Lock Suppression ..........................................................................................................12
5.6 Relay Interconnections .................................................................................................12
6Network Connection........................................................................................................13
7Default IP Address...........................................................................................................14
Cable Specification
4
1Cable Specification
The cabling system is based on Unshielded Twisted Pair Category 5e (Cat5e) or Category 6 (Cat6).
The cable must be annealed pure copper, meeting or exceeding the requirements defined in the
standard ANSI/TIA 568 C.2.
Failure to comply with this cable specification may result in erratic operation of equipment.
The specification below shows the minimum cable requirements, allow for extra cabling if
redundancy is required.
Connection
Cable
A
Access controller to each call
panel:
1x Cat5e or Cat6.
B
Access controller to locks:
2x 1.5mm² multi-stranded flex or singles (route through
any exit/fire switch or break glass for fail safe operation).
C
Access controller to exit
switch:
1 Pair UTP (2 cores), Cat5e or Cat6.
D
Access controller to fire switch:
1 Pair UTP (2 cores), Cat5e or Cat6.
1.1 Typical Configuration
FIGURE 1-1
Power Supply
6
3Power Supply
FIGURE 3-1
3.1 Mains Supply Connections
FIGURE 3-2
WARNING
Isolate mains supply before connecting.
Fused Terminal Block
Earth Bonding Conductor Point
Pre-Wired 12V to Internal Devices
Backup Battery Connections for
Sealed Lead Acid Battery
Output Voltage Adjustment
SYSTEM VOLTAGE 13.8VDC
Always test the output voltage.
Only adjust if required.
Fuse Holder
Mains Supply Cable from
Fused Spur
1.5mm² Twin + Earth
LIVE - BROWN
NEUTRAL - BLUE
EARTH - GREEN/YELLOW
Sheath
A
B
C
D
E
A
B
L
N
E
B
B
L
N
E
E
A
C
D
A
Access Controller
9
4.1 Readers Connections
Colour
To Cat5e/Cat6
Connection to Access Controller
Red
White/Blue
DC12V
Black
Blue
GND
Yellow
White/Orange
RS485- (B)
Purple
Orange
RS485+ (A)
Magnet for
Tamper Switch
Wall Bracket
Connections to
Access Controller
(See Table)
M3x6mm Screw
3x ST3x18mm Screws
(Supplied with Plugs)
NOTE Use Screws
Suitable for Wall Type
Lock Connections
10
FIGURE 5-1
5Lock Connections
5.1 Lock Distribution Board
DC12V IN
Lock Connections 1-4 (Lock supply and Relay Outputs)
Relay Loop Connections (Pre-connected)
FS1 – Lock Supply Fuses (2 Amp Time Delay)
5.2 Exit Switch Connections
FIGURE 5-2
For double pole push to exit / fire switches with fail open locks, see section 5.3.
A
B
C
D
A
C
B
D
Tabla de contenidos
Otros manuales de Sistema de intercomunicación de Entrotec
