Entel HT 44 Series Guía de configuración

PREPARING YOUR RADIO FOR USE

Attaching / removing the aerial

Attaching / removing the battery pack

1. To attach, carefully align the aerial with

the socket. Screw in the aerial clockwise

(taking care not to cross the thread) until it

is seated rmly with the accessory cover’s

rubber ring between the aerial and the top

of the radio. (A)

2.To remove, unscrew the aerial anti-clockwise.

(B)

1. To attach, locate the pegs on the bottom of the

battery into the slots on the radio and press

the top of the battery against the radio. Secure

battery by tightening the screw clockwise

by hand. (Do not use any implement or

overtighten). (C)

2.To remove, unscrew the locking screw

anti-clockwise and pull the battery away

from the top of the radio. (D)

SWITCHING ON, RECEPTION

AND SWITCHING OFF

1. To switch on, press and hold the on/off

button (1) on the front of the radio.

2.When the radio has passed its diagnostic tests,

it will emit a fanfare tone.

3.The radio will enter standby mode. This is

indicated by the LED Amber ashing once

every 5 seconds, signalling that the radio is

ready for use.

4.Adjust the volume control (2) to select the

desired volume level.

5. Using the channel buttons (3) ensure you have

the correct channel selected.

6.When receiving a valid signal, the LED will

illuminate steady green and audio will be

emitted from the radio’s speaker or audio

accessory (if attached)

7. When nished using the radio, switch off

by pressing and holding the on/off button

(1) until the radio beeps and the LED/LCD is

extinguished.

TRANSMITTING

1. Perform steps 1 through to 5 of Switching On,

Reception and Switching Off.

2.Before transmitting, monitor the channel

and make sure it is clear.

3.When receiving a signal, wait until the signal

stops before transmitting. The transceiver

cannot transmit and receive simultaneously.

4.Press the PTT (Push To Talk) button (4) to begin

your transmission. To conrm transmission the

LED illuminates red.

5. For best transmitted speech quality, you must

talk directly into the radio’s microphone (9) at

around 4cm between your mouth and the radio

complete, the charger.

6.Please note: if you talk into the top of the

radio or with your mouth further away, you will

transmit poor quality speech.

7. When the transmission is nished release the

PTT button.

EU DECLARATION OF CONFORMITY

We. Entel UK Limited of:

320 Centennial Ave, Centennial Park,

Elstree. WD6 3TJ United Kingdom

Tel +44 208 236 0032

info@entel.co.uk

Declare under our sole responsibility that the

product ranges specied below conform to

the following standards or other nominative

documents;

HT544, HT844 V2 series, HT944 V2 series,

EN 301 178-2 V1.2:2007

EN 60945:2002

EN 60950-1:2006 in accordance with

Directive 1999/5/EC

This declaration is valid for Directive 94/9/EC

until 19 April 2016

This declaration is valid for Directive 2014/34/

EU from 20 April 2016

HT544, HT844 V2 series, HT944 V2 series

EN 60079-0:2012

EN 60079-11:2012

Related certicates:

HT844 V2 series, HT944 V2 series

Sira 10ATEX2066X

HT9XX marking Ex ll 2 G Ex ib llC T4 Gb

HT8XX marking Ex ll 2 G Ex ib llA T4 Gb

HT544

IECEx SIR 10.0097X

Marking Ex ll 2 G Ex ib llA T4 Gb

Sira Certication. Unit 6, Hawarden Industrial

Park,Hawarden, Deeside. CH5 3US, UK

Notied Body No. 0518

Quality Assurance Notication:

Intertek. Intertek House, Leatherhead

KT22 7SB, UK

Notied Body No. 0359

Name: Mike Jamieson

Position: Quality Manager

Date: 1st December 2015

Signed:

www.entel.co.uk

HTx44 Series

HT544 |HT844 | HT944

Quick Start User Guide

Designed in the United Kingdom

Quick Start User Guide V2.1

HTx44 Series

HT544 |HT844 | HT944

INTRODUCTION

The Entel HTx44 series are a range of professional IP68 submersible

marine handheld transceivers that operate on the VHF marine band. They

have 56 marine international channels and 36 dealer programmable private

channels.

This quick guide provides basic guidance for operating your radio.

A full version of this user guide is available to download from our website.

www.entel.co.uk.

To meet your exact requirements the radio may have been customised by

your Entel dealer. These features will be explained in a separate guide

issued by the dealer.

PACKING LIST

HTx44 Marine VHF transceiver

CNBxxx Rechargeable Li-Ion battery

CBH950 Spring loaded belt clip

CCAHT Trickle charger pod

CAT40 High efciency antenna

CWCHT Mains adaptor

OPTIONAL ACCESSORIES

Attaching and removing accessories

To attach an accessory, remove the accessory cover by unscrewing the

locking screw anti-clockwise (leave the cover attached or store in a safe

place).

Plug the accessory into the socket, then carefully

tighten the locking screw clockwise until nger tight

(do not overtighten or use any implement)

To remove an accessory, unscrew the locking

screw of the acc essory by hand in an anti -clock wise

direction.

Ensure you re-t the accessory socket cover (the

radio is not submersible without the socket covered)

BATTERY INFORMATION

Battery charging

1. Connect the AC adapter to the charger pod and plug in.

2.Turn the transceiver off.

3.Insert the battery pack into the charger pod, either with or without the

transceiver attached. The charger LED status light changes to red and

charging begins.

4.When charging is complete, the charger status LED changes from red

to green (a fully discharged battery pack will take approximately 6 hours

to recharge).

A ashing red LED on the charger indicates there is a problem with the

battery. Remove the battery from the charger and consult your Entel Dealer.

CAUTION

BATTERY PACK PRECAUTIONS

• Do not recharge the battery pack if it is already fully charged. Doing so

may cause the life of the battery pack to shorten or the battery pack may

be damaged.

• After charging is complete, remove the battery from the charger. If the

power to the charger is turned off and on again, charging will restart and

the battery will become overcharged.

• Please ensure that the radio is turned off before placing it in the charger

and never switch a radio on whilst in the charger.

• Only use Entel branded battery pack and chargers.

• Do not short the battery terminals or dispose of the battery in a re.

• Do not charge the transceiver and/or battery pack if they are wet.

DANGER

DO NOT DISASSEMBLE OR MODIFY THE BATTERY IN ANY WAY!

Your Entel battery pack incorporates safety circuitry to avoid danger. If the

safety circuitry is damaged or bypassed, or the battery cells are damaged

directly, they may generate extreme heat, smoke, rupture and emit ames.

CONTROLS & INDICATORS

Above approvals apply to specic models only

7 KEY LCD

1. On/Off button. Press and hold to turn the radio on or off

2.Volume control

3.Channel up / down buttons

4.Push To Talk (PTT) button. Press to speak and release to listen

5. Dealer programmable button (ask your dealer for more information).

6.LED Indicator

Red steady - Transmitting

Red ashing slowly - Battery needs recharging

Green - Receiving

7. Change channel mode from INT/USA/CAN

8.MEM Button: Adds or removes the currently selected channel to or

form the scan list

SCAN Button: Starts/stops scanning the channels added to the scan

list plus CH16

16 Button: Toggles between the currently selected channel and

channel 16

MON Button: Short press momentarily opens squelch. Long press

latches squelch open (short press re-sets)

9. Microphone

Introduction

Your Entel radio is supplied with a high performance

Lithium-Ion (Li-Ion) battery. These batteries:

•Extend talk time

•Reduce the battery’s size and weight

•Do not suffer from ‘memory effect’ that

reduces the life of Ni-Cad and NiMH batteries

•Have a low toxicity, therefore reducing the

impact on the environment

Battery Pack Precautions

•Switch the transceiver OFF before charging

•Charge the battery pack before use

•Do not recharge the battery pack if it is already fully

charged

•Charge the battery in accordance with the instructions

enclosed with your charger.

•Do not charge the transceiver and/or battery pack if

they are wet

•Do not charge the battery pack in a hazadous area

The battery pack includes potentially hazardous

components. Please:

•Do Not disassemble or reconstruct battery

•Do Not short-circuit the battery

•Do Not incinerate or apply heat to the battery

•Do Not immerse the battery in water unless attached

securely to the radio or get it wet by other means

•Use only the specified charger and observe charging

requirements

•Do Not pierce the battery with any object or strike it

with an instrument

•Do Not use the battery pack if it is damaged in any way

•Do Not reverse-charge or reverse-connect the battery

•Do Not touch a ruptured or leaking battery

If liquids from the battery get into your eyes, immediately:

•Wash your eyes out with fresh water and avoiding

rubbing them.

•Seek medical treatment

Battery Pack

•If a battery is not to be used for an extended period of

time (e.g. several months) remove the battery pack

from the equipment and store in a cool and dry location

(around 0°C) part charged

Do not fully discharge the battery before storage

Battery Care / Information

•Each charge cycle reduces the battery’s life. Minimise

the number of times you charge your battery espe-

cially in hotter environments which further shortens a

battery’s life

Battery Charging

1. Connect the AC adapter to the charger pod. The LED

status light will illuminate green indicating ready for

charge

2. Turn the transceiver off

3. Insert the battery pack into the charger pod, either

with or without the transceiver attached. The LED

status light changes from green to red and trickle

charge begins

4. A fully discharged battery pack will take approximately

6 hours to charge, depending on the remaining power

condition.When charge is complete, the LED status

light turns green.

The battery pack has an over-current protection circuit

fitted.When charging a completely discharged battery

i.e. first charge, ensure the battery is removed from the

radio and then re-attach (if fitted to radio when

charging).This will reset the protection circuitry and

ensure normal operation.This process will need to be

repeated if the battery is allowed to completely

discharge in the future. In normal use this is unlikely.

Battery Indicator (HTX44 Only)

For your safety and convenience your transceiver

continually monitors the battery pack and gives an

indication on the LCD.

•3 Segments: Fully charged

•2 Segments: 1 hour

•1 Segment: 20 mins

Note: Only genuine Entel batteries should be used.

With Entel batteries customer satisfaction is assured, as

you avoid risks from sub standard, potentially dangerous

battery packs from 3rd party manufacturers, ensuring it

delivers the expected capacity and endurance.

On HT series batteries a breathable membrane is used.

This is clearly marked on the battery label. Piercing the

membrane will allow water ingress to the battery and

will invalidate the warranty.

Common

PreparingYour Radio For Use

Attaching / Removing the Battery Pack

1To attach, locate the pegs on the bottom of the

battery into the slots on the radio and press the

top of the battery against the radio. Secure

battery by tightening the screw clockwise by hand

(Do not over tighten).

2To remove, unscrew the locking screw

anticlockwise and pull the battery away from the

top of the radio.

Common

Attaching / Removing Audio Accessories

3To attach, remove the accessory cover by unscrewing the

locking screw anti-clockwise (leave cover secured under

antenna as this provides a waterproof seal). Attach

accessory plug by locating over the socket. Carefully tighten

the locking screw clockwise until finger tight (do not

tighten with a screwdriver etc).

4To remove, unscrew accessory plug the locking screw by

hand in an anti-clockwise direction (carefully use a coin or

screwdriver if too tight). Ensure you re-fit the accessory

waterproof cover so as to protect the accessory socket.

Carry Options

CLC953 Heavy duty black leather case with strap and belt loop.

CBH950 Spare spring loaded belt clip.

Audio Accessory Options

CMP950HD Heavy duty submersible speaker microphone.

EA12/950 D-shaped earpiece with in-line PTT/microphone and VOX*.

EA15/950 Transparent acoustic tube earpiece with in-line PTT/microphone.

EA19/950 D-shaped earpiece with boom microphone and large in-line PTT and VOX*.

EPT40/950 Bone conductive combined earpiece microphone with large in-line PTT.

CXR5/950 Bone conductive skull microphone with large in-line PTT.

CXR16/950 D-shaped earpiece and throat microphone with large in-line PTT.

CHP950HS Single earpiece ear defender headset with boom mic and in line PTT for hard hat andVOX*

CHP950HD Double earpiece defender headset with boom mic and in line PTT for hard hat and VOX*.

CHP950D Double earpiece headband defender headset with boom mic and in line PTT andVOX*.

CXW640 BNC antenna adapter for external aerial connection.

CAT40 Replacement high efficiency helical antenna.

Battery and Charger Options

CNB950E Spare 1800mAh Lithium-Ion battery pack with rear clip.

CSAHT 1-way intelligent rapid charger.

CSBHT 6-way intelligent, rapid charger.

CCAHT-230 1-way trickle charger with 230V mains adapter.

CCAHT-110 1-way trickle charger with 110V mains adapter.

CCAHT-12 1-way trickle charger with cigarette lighter lead, 12V DC operation.

Optional Accessories

Common

Battery Communications

(HTX44 Only Excluding ATIS models)

Each battery used with your radio has a microproces-

sor fitted, which logs the number of times your battery

has been charged.

On a radio with an LCD display, the number of times

the battery has been charged, together with the re-

maining charge cycles available, will be shown during

switch on (if not de-activated by your dealer).

The warranty on all batteries is 12 months or 450

charge cycles, whichever is the sooner. After 420 cy-

cles, at switch on the radio will emit a series of short

tones, and on LCD models a waste bin icon will flash to

alert you to the need to buy a new battery.

Battery Care / Information

After 450 cycles, at switch on the radio will emit a

series of long warning beeps that indicate the number

fo times the battery has been charged exceeds the

charge count & the battery needs to be replaced.

Note: only genuine Entel batteries should be used.

Only genuine batteries offer the battery charge count

feature informing you when the battery is reaching the

end of its useful life. Non ATEX batteries will not work

on ATEX radios ensuring customer safety.

Common

Attaching and Removing Accessories

To attach an accessory: Remove the accessory cover by

unscrewing the locking screw anti-clockwise (leave cover attached

or store in a safe place). Attach accessory plug to the socket.

Carefully tighten the locking screw clockwise until finger tight (do

not tighten with a screwdriver etc).

To remove an accessory: Unscrew the locking screw of the

accessory by hand in an anti-clockwise direction (carefully use a

coin or screwdriver if too tight). Ensure you re-fit the accessory

cover so as to protect the socket.

Optional Accessories

For complete up to date list of optional accessories visit: www.entel.co.uk

Other Accessories

EPROGHT Programming software and lead (Only available to Authorised Dealers)

PTT950 Waterpoof PTT

PTT951E Waterproof PTT

PTT951C Waterproof PTT

* VOX = Voice Operated Transmit (hands free operation)

The use of non Entel approved accessories will invalidate your ATEX intrinsically safe approval. Refer to

certificate Sira 10ATEX 2066X for permitted accessories.

Turning the Radio On and Off

To turn the radio ON press and hold the red power button until the LCD iluminates and a power

on tone is generated after 1 second to indicate the transceiver has passed its self-diagnostic test.

To turn the radio OFF press and hold the power button until the LCD displays “POWERING OFF”

and its illumination switches off.

UsingYour Radio

Before using your radio you may need to adjust the volume on the radio to take in to account

background noise. Adjust the volume using the rotary control on the top of the radio.

UsingYour Radio

1. Turn the transceiver on using the power button. During standby the LED indicator will pulse

amber every 3 seconds, verifying its circuitry is functioning correctly. Adjust the volume using the

rotary control on top of the radio. After power-on, the transceiver will always default to the last

channel selected.

2. Select the desired channel using the [UP/DOWN] buttons. A full listing of channels can be found

on page 17 to 19.

3. When receiving a signal the LED indicator illuminates green.

Reception

Transmitting

1. Perform steps 1 through 2 of RECEPTION.

2. Before transmitting, monitor the channel and make sure it is clear.

3. For communications over short distances, press the [H/L] button or press & hold the MEM button

to toggle from High Power (4 watts) to Low power (1 watt) denoted by an L on the LCD,

(available on the HT844 only). Transmitting on 1 watt prolongs battery life, and should be selected

whenever possible.

4. When receiving a signal, wait until the signal stops before transmitting. The transceiver cannot

transmit and receive simultaneously.

5. Press the [PTT] (Push-To-Talk) button to begin your transmission.To confirm transmission is in

progress, the LCD indicator illuminates TX and the LED illuminates red.

6. Hold the transceiver 1 inch from your mouth and speak slowly and clearly into the microphone.

7. When the transmission is finished release the [PTT] button.

HTX44

HT844 & HT944

Standard Features:

•Environmentally protected to IP68 i.e. submersible

to 5 metres for up to 60 minutes

•Robust design, exceeds MIL-STD-810C/D/E/F

•1800 mAH Lithium-Ion battery for superior operational time.

•Exceptionally loud and clear audio

•Automatic power save to further increase operational time

•Low battery alert indicates when the battery needs charging or replacing

•LCD screen to display channel number and current

settings \ status (HTX44 Only)

•INT, USA, CAN channels (HTX44 Only)

•Ch 16 shortcut button

•Scan, Monitor and MEM button

•Battery charge count to indicate when a battery needs replacing.

•Full transmit power output 4 Watts (HT844 only), 1 Watt.

Dealer Programmable Features:

•Key lock button

•VOX (Voice Operated Transmit) Function

•Prefixed minimum volume level and fixed bleep level

Common

Functions

The Scan Function

Programming the Scan Function:

1. Select the desired channels to be scanned using the and buttons.

2. Press the [MEM] button to store the channel in the transceiver’s memory. [M] will be

displayed on the LCD if the channel is memorised and will be scanned.

3. To add further channels, repeat steps 1 and 2.

4. To delete a channel from the transceiver’s scan list, press the [MEM] button on a channel

that displays the [MEM] icon until the icon disappears.

5. All channels programmed remain in the transceiver’s scan memory, even if the power is

switched off.

Using the Scan Function:

Once a Scan list has been programmed, you can start scanning by pressing the [SCAN]

button.The scan proceeds from the lowest to the highest programmed channel number

and stops on channels when a transmission is received.The transceiver will display the

channel number and alias as it is being scanned.

To stop the scan at any time, press the [SCAN] key again.

VOX (Voice Operated Transmit)

In VOX mode the transceiver will react to your voice, and transmit automatically without you

having to press the PTT button when it receives audio above a selected level. There is always a

slight delay for the electronic switching and consideration will need to be given.To get optimum

performance from the VOX feature you should use a noise cancelling headset or earpiece

microphone (see accessory options).

Using the VOX Feature:

To use the VOX feature, assign it to a button using the Entel Programmer and a

programming lead. Press the assigned button to enable \ disable it.The VOX symbol will be

displayed on the LCD when the VOX is enabled.

Changing the Sensitivity of the VOX:

To control the sensitivity of the VOX assign the “VOX Level” to a button using the Entel

Programmer. Press the button to display the current level, then use the rotary control on top

of the radio to select the level you wish (the lower the level the lower the sensitivity).Then

press the PTT to select the level and return to normal radio operation.

HTX44

Channels

International (INT), USA and Canadian (CAN) Modes

The HT844 / HT944 has 3 different modes: International (INT), USA and Canadian (CAN), which

are displayed on the LCD. These modes can be changed by applying the “Change Mode” function

to a button.The mode can be selected by pressing the button to toggle through the options and

pressing the PTT to select the desired mode.

Emergency Channels

To select the emergency channel, press the [16] button from any channel. Channel 16 appears on

the display.

To recall the previous channel used, press the [16] button once again.

Monitor Channels

Press the monitor button [MON] to defeat the squelch mute this is displayed as a speaker on

the LCD and release to mute the radio. A long press will hold the squelch mute open until

pressed again to cancel again to return to squelch mute.

SIMPLEX / DUPLEX CHANNEL USE

Your transceiver has been factory programmed in accordance with FCC (USA), Industry Canada

and International regulations.The mode of operation cannot be altered from simplex to duplex

or vice versa. Simplex or duplex mode is automatically activated, depending on the channel set

and whether USA, Canadian (CAN), or International (INT) mode is selected.

Refer to the channel charts listed on pages 17 to 19 of this user manual.

If you have a licence to use a specific simplex or semi-duplex channel, contact your dealer who

may be able to programme your channel using the transceiver’s private channel memory.

High \ Low Power Channels (HT844 Only)

To toggle the power level from High (4 watts) to Low (1 watt) press & hold the MEM button, the

power of the channel will be indicated by an H for High or L for Low on the LCD.

HTX44

Controls

1 Antenna \ Antenna

Connector: Used to attach the

antenna of the radio.

2 Accessory Connector: The

accessory connector and

accessory cover.

3 Encoder: The rotary controller.

4 LCD: The LCD of the radio.

5 Scan Button: Starts / Stops

scanning the memorised

channels.

6 Up Button: The up button is

used to change the channels.

7 Down Button: The down

button is used to change the

channels.

8 [MEM] Memory Button: The

Memory button memorises a

desired channel for scanning.

9 Monitor Button: Press to

monitor the channel without the

squelch mute.

10 Power Button: Powers the

radio on and off.

11 16 Button: Pressing the button

selects channel 16.

12 Speaker: The radio’s speaker.

13 Microphone: Internal

condenser microphone.

HTX44

LCD Indicators

Indicator Description

High power selected (4 Watts) (HT844 model only).

Low power (1 Watt).

Indicated channel is memorised for scanning.

Voice operated transmit mode enabled.

Indicates the channel set for USA.

Indicates the channel set for Canadian.

Indicates the channel set for International.

The Monitor function is enabled.

Battery life indicator.

Indicates keypad is locked, excluding the PTT.

Either P, F or L are displayed as Private channel number selected.

Duplex channel selected (not simplex).

HTX44

Channel Chart

HTX44

CH Channel Set S/D Frequency Channel Use

USA CAN INT Receive Transmit

1A XS 156.05000 PORT OPERATION AND COMMERCIAL

1X X D 160.65000 156.05000 PUBLIC, PORT OPERATIONS

2X X D 160.70000 156.10000 PUBLIC, PORT OPERATIONS

3A XS 156.15000 US GOVERMENT, COAST GUARD

3X X D 160.75000 156.15000 PUBLIC, PORT OPERATIONS

4A XS 156.20000 COMMERCIAL FISHING

4XD 160.80000 156.20000 PUBLIC, PORT OPERATIONS

5A X X S 156.25000 PORT OPERATIONS,VTS IN SEATTLE

5XD 160.85000 156.25000 PUBLIC, PORT OPERATIONS

6X X X S 156.30000 INTER-SHIP SAFETY

7A X X S 156.35000 COMMERCIAL

7XD 160.95000 156.35000 PUBLIC, PORT OPERATIONS

8X X X S 156.40000 COMMERCIAL (INTER-SHIP ONLY)

9X X X S 156.45000 BOATER CALLING CHANNEL

10 X X X S 156.50000 COMMERCIAL / INTERSHIP

11 X X X S 156.55000 COMMERCIAL / PORT OPERATIONS

12 X X X S 156.60000 PORT OPERATION

13 X X S 156.65000 INTER-SHIP NAVIGATION SAFETY

13 XS 156.65000 INTER-SHIP NAVIGATION SAFETY

14 X X X S 156.70000 PORT OPERATION

15 XR 156.75000 - SHIP MOVEMENT

15 X X S 156.75000 SHIP MOVEMENT \ INTERSHIP

16 X X X S 156.80000 INTERNATIONAL DISTRESS

17 X X X S 156.85000 STATE CONTROLLED \ INTERSHIP

18A X X S 156.90000 COMMERCIAL

18 XD 161.50000 156.90000 PORT OPERATION, SHIP MOVEMENT

19A X X S 156.95000 COAST GUARD

19 XD 161.55000 156.95000 PORT OPERATION, SHIP MOVEMENT

20A XS 157.00000 PORT OPERATION

20 X X D 161.60000 157.00000 PORT OPERATION AND SHIPMENT

20 XD 161.60000 157.00000 PORT OPERATION AND SHIPMENT

21A X X S 157.05000 U.S. GOV, CANADIAN COST GUARD

21 XD 161.65000 157.05000 PORT OPERATION, SHIP MOVEMENT

Controls

14 Orange Button: The orange button, the

functionality of which depends on the configuration

of the radio (by default long press is region).

15 LED (Light Emitting Diode): The LED indicator, which indicates the status of the radio:

• RED Steady = Transmitting

• RED Flashing slowly = Battery needs re-charging

• GREEN Steady = Receiving

• AMBER Steady = Receiving but with incorrect subtone.

• AMBER Pulse every 3 s = Radio in standby mode.

16 Battery Screw: The screw used to attach or remove the battery.

17 Belt Clip: The spring loaded belt clip, which can be used to attach the radio to your belt.

18 Upper Side Button: The upper function button, the functionality of which depends on the

configuration of the radio (by default press to PTT).

19 PTT: The PTT (Press To Talk) button, hold down to transmit, release to receive.

20 Lower Side Button: The lower function button, the functionality of which depends on the

configuration of the radio (by default long press key lock).

21 Battery: The rechargeable lithium-ion battery pack.

HTX44

Channel Chart

CH Channel Set S/D Frequency Channel Use

USA CAN INT Receive Transmit

74 X X X S 156.72500 PORT OPERATIONS

75 X X S 156.77500 PORT \ GUARD CHANNELS

76 X X S 156.82500 PORT \ GUARD CHANNELS

77 X X S 156.87500 PORT OPERATIONS

77 XS 156.87500 PORT OPERATIONS \ INTERSHIP

78A X X S 156.92500 NON-COMMERCIAL

78 XD 161.52500 156.92500 PUBLIC \ PORT OPERATIONS

79A X X S 156.97500 COMMERCIAL

79 XD 161.57500 156.97500 PORT OPERATION, SHIP MOVEMENT

80A X X S 157.02500 COMMERCIAL

80 XD 161.62500 157.02500 PORT \ SHIP MOVEMENT

81A X X S 157.07500

81 XD 161.67500 157.07500 PORT OPERATION

82A X X S 157.12500

82 XD 161.72500 157.12500 PUBLIC \ PORT OPERATIONS

83A X X S 157.17500

83 X X D 161.77500 157.17500 PUBLIC CORRESPONDENCE

84A XS 157.22500 PUBLIC CORRESPONDENCE

84 X X X D 161.82500 157.22500 PUBLIC \ PORT OPERATIONS

85A XS 157.27500 PUBLIC CORRESPONDENCE

85 X X X D 161.87500 157.27500 PUBLIC CORRESPONDENCE

86A XS 157.32500 PUBLIC CORRESPONDENCE

86 X X X D 161.92500 157.32500 PUBLIC CORRESPONDENCE

87A XS 157.37500 PUBLIC CORRESPONDENCE

87 X X D 161.97500 157.37500 PUBLIC CORRESPONDENCE

87 XS 157.37500 PUBLIC CORRESPONDENCE

88A XS 157.42500 COMMERCIAL

88 X X D 162.02500 157.42500 PUBLIC CORRESPONDENCE

88 XS 157.42500 PUBLIC CORRESPONDENCE

Key:

•S = Simplex.

•D = Duplex.

•R = Receive Only.

Channel Chart

HTX44

CH Channel Set S/D Frequency Channel Use

USA CAN INT Receive Transmit

22A X X S 157.10000

22 XD 161.70000 157.10000 PORT OPERATION, SHIP MOVEMENT

23A XS 157.15000 U.S. GOVERNMENT ONLY

23 X X D 161.75000 157.15000 PUBLIC CORRESPONDENCE

24 X X X D 161.80000 157.20000 PUBLIC CORRESPONDENCE

25 X X X D 161.85000 157.25000 PUBLIC CORRESPONDENCE

26 X X X D 161.90000 157.30000 PUBLIC CORRESPONDENCE

27 X X X D 161.95000 157.35000 PUBLIC CORRESPONDENCE

28 X X X D 162.00000 157.40000 PUBLIC CORRESPONDENCE

37 XS 157.85000 MARINA CHANNEL

60 X X D 160.62500 156.02500 PUBLIC \ PORT OPERATIONS

61A X X S 156.07500 -

61 XD 160.67500 156.07500 PUBLIC \ PORT OPERATIONS

62A XS 156.12500 -

62 XD 160.72500 156.12500 PUBLIC \ PORT OPERATIONS

63A XS 156.17500 PORT OPERATIONS

63 XD 160.77500 156.17500 PUBLIC \ PORT OPERATIONS

64A X X S 156.22500

64 X X D 160.82500 156.22500 PUBLIC \ PORT OPERATIONS

65A X X S 156.27500 PORT OPERATIONS

65 XD 160.87500 156.27500 PUBLIC \ PORT OPERATIONS

66A XS 156.32500 PORT OPERATIONS

66 XD 160.92500 156.32500 PUBLIC \ PORT OPERATIONS

67 X X S 156.37500 INTERSHIP

67 XS 156.37500

68 X X X S 156.42500 NON-COMMERCIAL

69 X X X S 156.47500 INTERSHIP

70 X X X R 156.25000 - DIGITAL SELECTIVE CALLING

71 X X X S 156.57500 PORT OPERATIONS

72 X X X S 156.62500 NON-COMMERCIAL \ INTERSHIP

73 X X X S 156.67500 INTERSHIP

HTX44

HT942

Controls & Indicators

3Channel / Scan

control

Antenna

5Dealer

programmable

button 1

4Push To Talk

(PTT) button

6Dealer

programmable

button 2

1On / Off

2Volume control

Speaker

Microphone

1On / Off button. Press to turn radio on, press and hold to turn off.

2Press up / down buttons to increase / reduce volume.

3Channel / Scan control. Rotate to select the desired channel or scan setting.

4Push To Talk (PTT) button. Press to speak and release to listen.

5Dealer programmable button 1 (ask your dealer for more information).

6Dealer programmable button 2 (ask your dealer for more information).

7Dealer programmable button 3 (ask your dealer for more information).

8LED indicator.

•RED steady = Transmitting

•RED flashing slowly = Battery needs re-charging

•GREEN steady = Receiving

•YELLOW steady = Non valid signal detected

•YELLOW flashing rapidly = Scanning

7Dealer

programmable

button 3

8LED indicator

Standard Features:

•16 programmable channels

•Top mounted monitor button

•CTCSS & DCS (analogue & digital squelch) with squelch tail elimination (removes the ‘shh’ noise)

•Exceptionally loud and clear audio

•Robust design, exceeds MIL-STD-810C/D/E/F

•Environmentally protected to IP68 i.e. submersible to 5 metres for up to 60 minutes

•1800mAH Lithium-Ion battery for superior operational time

•Full band switching allows access to all channels in each band

•Battery charge count

•Radio cloning mode

•Low battery alert indicates when the battery needs recharging

Dealer programmable features:

•VOX for hands free operation

•High / Low transmit power

•Normal & priority scan (programmable per channel position)

•Panic (personal attack) button causes high pitch, high volume, siren tone to be emitted from the

radio’s speaker

•Key lock button

•Prefixed minimum volume level and fixed bleep level

•Talkaround (allows communication away from a base station)

•Transmit time out-timer (ensures channels are not blocked)

•Voice scrambler with 1 code per channel (option)

•Automatic power save to further increase operational time

•User adjustable squelch level

HT942

Otros manuales para HT 44 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario