EnGenius Caprive portal ready Manual de usuario

EnGenius Captive Portal “Ready”

Quick Installation Guide

Version 1.1 (for Cloud4Wi)

*** MUST READ ***

The package labelled “Captive Portal Ready” herein contains a Third-Party firmware &

management feature It has distinctly different properties, configuration and capabilities

of that the stock product mentioned in the datasheet, CD user manual and box

packaging This Quick Installation Guide supersedes any datasheet, CD user manual

and information on the box packaging to contain important instructions in setting up

your EnGenius Captive Portal Ready wireless networks Please read and follow this

guide thoroughly to have an enjoyable experience in setting up your EnGenius Captive

Portal Ready Wireless Network

Note: Guest authentication feature requires a separate paid subscription from third-

party cloud captive providers to work

Check List:

•Internet connection should be already setup & ready to use* (ADSL /Cable/Fiber modem router)

•Modem/Router must provide RJ45 port to connect with EAP300-CP or ENS202EXT-CP An Ethernet cable

is further required for the ENS202EXT-CP

•Internet Browser (Recent version of Microsoft Internet Explorer or Firefox browser)

•A pencil or pen ready to use “My Personal Notes” on the last page to assist you in remembering

any account names and passwords created

Important Notes:

•(*) The internet connection should give you the ability to ping www yahoo com (resolve DNS) and to

normally browse a web page via http and https (SSL) If in doubt, use a laptop or computer with your

existing internet connection (which you will be connecting the equipment to) and type

http://www yahoo com on your browser If there is no response, you need to resolve this with your internet

service provider before proceeding further this Quick Installation Guide

Installing the device

ST P 1

Follow the instructions on the user ID-sticker The sticker is located on the device

Go to http://controlpanel cloud4wi com and logon with your your account If you do not have an

account, kindly contact an Authorized Cloud4WI Distribution Partner

ST P 2

Once you have logged in, click on <+Create New> to activate the device with your account

Under the Router Menu, kindly ensure the fields are entered as follow:

Router type : nGenius

MAC address : 88:DC:96:XX:XX:XX

Note: Change XX to the similar characters as shown on your device or ID-Sticker.

Click on <Save> when completed

ST P 3

After the adding the device in the controlpanel cloud4wi com, connect a LAN cable from the LAN

port of your existing Internet modem router to the ethernet port of the EnGenius Captive Portal

Ready device and power up The device will perform an initial setup which the status LED will

constantly blink for 2 minutes After approximately two minutes, the product is ready This can be

verified by the 3 LEDs on the device (The WLAN LED of the ENS202EXT-CP is not in use in the

Captive Portal Mode)

For ENS202EXT-CP devices,

Note: The ENS202EXT-CP must only be powered with the supplied 24V power adapter via the PoE

(Power over Ethernet) injector

For EAP300-CP devices,

Note: The EAP300-CP supports both IEEE802 3af PoE (Power over Ethernet) or the included

power adapter You may use either one as the power source Do not use both at the same time.

In the wireless SSID scan, you can find the SSIDs by ‘My Hotspot is getting ready’ Once the initial

setup is completed, you find 3 SSIDs: MyHotspot, My Private (key is on the sticker) and Hotspot

[part of user ID]@[IP-address] This last SSID is the help SSID This is the IP-address that is

assigned on your Local Area Network The fourth SSID is the Wireless Mesh which is used to

repeat the wireless signal to another device if the other device has not Ethernet connection

ST P 4

Your device is now ready to use Connect to the SSID “ My Hotspot” and a simple authentication will appear

as below before internet access is allowed

Changing of Guest Access

For any changes of access such as vouchers, email, sms, social media login by guest, you can

Kindly note paid subscription applies accordingly

Changing of hardware configuration

To change the broadcast SSIDs and/or assign preferred passwords to the device, you can type in

the IP-address of the device at the address field in the web browser if your computer is connected

to the Local Area Network Otherwise, you can wirelessly connect to the default SSID “My Private-

XXXXXX” using the serial number of the device as the passphrase and then typing the IP-address

of the device in your web browser

Installing additional devices

Because of the Mesh capabilities, additional devices can be added wirelessly or by the wired LAN

If you want to add it wirelessly, place the additional device close to the first device with the wired

internet access

Single Step

Confirm that the first device is powered up and connected to your internet router Power up the

additional device The device status light will start blinking constantly for next 2 minutes

In the wireless network scan you can find the SSIDs by ‘My Hotspot is getting ready’ while the

additional device is preparing itself Once the initial setup is complete , the device will reboot and

now you will find 2 SSIDs with 2 different assigned IP addresses You can now power if off and

relocate the additional device in the wireless blindspot area where you want to extend the wireless

coverage

___________________________________________________________________________

Completion of "Quick Installation Guide"

Kindly visit http://www wifiabc com and click on Knowledge Base for a complete

guide and tutorials on the Captive Portal Ready Devices, such as changing SSIDs,

adding or changing passphrase, blocking guest to Local Area Networks and VLANs

configuration

Quick Troubleshooting notes:

Cannot see the SSID “HotspotAABB[email protected]. .8”

Make sure the device is properly connected to your Local Area Network or Internet router which

has access to the internet If connecting additional devices by wireless mesh to the first device, try

not to exceed 10 meters during initial setup After setup, you can relocate it further To restart initial

setup, power up device for at least 1 minute, then press-holding the reset button for 12 seconds

before releasing with a pointed object You can verify the device's response from the LED lights

Cannot connect to “My Private-AABBCC” or “HotspotAABB[email protected]. .8”

The 2 SSIDs are secured with an encryption pass-phrase The pass-phrase is the serial number of

the device and also can be located on the ID-Sticker (key)

My personal Notes:

My MAC Address

88 : DC : 96 : : :

(SSID)Name Password

Account Name

Guest Access

Node Name (SSID#1)

Node Name (SSID#2)

My Memos:

_______________________________________________________________

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de EnGenius

EnGenius

EnGenius ENS200 Manual de usuario

EnGenius

EnGenius EOC5611P Manual de usuario

EnGenius

EnGenius ENH700EXT Manual de usuario

EnGenius

EnGenius ENS200 Manual de usuario

EnGenius

EnGenius EOC2611P Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

EnGenius

EnGenius EWS371AP Manual de usuario

EnGenius

EnGenius EMD2 Manual de usuario

EnGenius

EnGenius EAP600 Manual de usuario

EnGenius

EnGenius EAP 11AC Series Manual de usuario

EnGenius

EnGenius ENH210EXT Manual de usuario

EnGenius

EnGenius EOC5611P Manual de usuario

EnGenius

EnGenius EWS357APV3 Manual de usuario

EnGenius

EnGenius EWS510AP Manual de usuario

EnGenius

EnGenius EWS370AP Manual de usuario

EnGenius

EnGenius ENH900EXT Manual de usuario

EnGenius

EnGenius EOA3630 Manual de usuario

EnGenius

EnGenius EAP300 Manual de usuario

EnGenius

EnGenius M35 Manual de usuario

EnGenius

EnGenius ENS200EXT Manual de usuario

EnGenius

EnGenius ECB150 Manual de usuario

EnGenius

EnGenius ENH202 Manual de usuario

EnGenius

EnGenius ENH200 Manual de usuario

EnGenius

EnGenius EAP1200H Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario

EnGenius caprive portal ready Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas