ENFORCER E-931CS22RRC Manual de usuario

E-931CS22RRC

Range: 22ft. (7m)

Retro-Reflective Photoelectric

Sensor Entry Alert System

Sensor

Caution:

ENFORCER®

Included:

E-931ACC-R

Reflector

E-931CS22RRC

Transmitter/Receiver E-931ACC-S

Speaker/Electronic Chime

ENFORCER

E-931ACC-BLS4

E-931ACC-BLR1

Adapter

INSTALLATION MANUAL

Features:

••

•Retro-reflective photoelectric sensor.

••

•Range: Up to 22 feet (7m).

••

•Perfect for monitoring an entrance, or for counting

foot traffic with optional counter.

••

•Will make “ding-dong” sound or siren sound when

the beam is interrupted.

••

•Speaker volume can be adjusted or turned off.

••

•When in siren mode, sounding time is adjustable

from 3 to 30 seconds.

••

•9VDC adapter included.

•

This sensor was not designed to prevent bodily injury or loss of life.

•

Use of this sensor in certain security applications may be regulated by local laws or codes.

SECO-LARM is not responsible for compliance with such laws or codes.

••

•All components plug into each other.

No hard wiring required.

••

•Optional counter available (E-931ACC-C).

••

•Optional second speaker available (E-931ACC-S).

••

•Includes the following:

— Retro-reflective photoelectric sensor.

— Reflector.

— Speaker/electronic chime.

— 9VDC adapter.

Specifications:

Troubleshooting:

Dimensions:

E931S22RRC_101204.pmd PITSW3

E-931CS22RRC

Retro-Reflective Photoelectric Entry Alert System

22' (7 m)

Sensor: 8-13 VDC, Chime: 12VDC

100mA Max.

30mA

IR LED

Relay (AC 120V/DC 24V, 2A)

-4

F (-20

C) ~ 122

F (50

~1 sec. for Chime, 30 sec. for Alarm

Adjustable from 0 ~ max.

Adjustable 3~30sec. for alarm

Ground output (100mA)

Chime / Off /Alarm (Select by switch)

All Included

Model Number

Type

Sensing Range

Voltage Supply

Total Current Consumption

Stand-by Current

Light Source

Control Output

Ambient Temperature

Speaker Response Time

Speaker Volume

Alarm Time Range

External Chime Output

Speaker Output

Mounting Brackets

Red LED does not turn on. 1) Reflector and/or sensor is misaligned.

2) No power.

1) Adjust the reflector and/or sensor for

proper alignment

2) Check power adapter and cable.

Sensor does not detect the object. Sensor not aligned properly. Change the angle of the sensor or

reflector.

Trouble Remedy(s)Possible Origin(s)

NOTICE:

The information and specifications printed in this manual are current at the time of publication. However,

the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right

to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

or in part, without the written permission of SECO-LARM.

SECO-LARM®U.S.A., Inc.,

16842 Millikan Avenue, Irvine, CA 92606

Tel: 800-662-0800 / 949-261-2999

Fax: 949-261-7326 Website: www.seco-larm.com E-mail: [email protected]

WARRANTY:

ENFORCER Photobeam Sensors are warranted against defects in material and workmanship while

used in normal service for a period of one (1) year from the date of sale to the original customer. Our obligation is

limited to the repair or replacement of any defective part if the unit is returned, transportation pre-paid, to SECO-LARM.

23/8" (60mm)

5/16" (8mm)

2" (50mm)

27/16" (62mm)

213/16" (71mm)

23/8" (60mm)

13/8"

(35mm)

13/16" (30mm)

2" (50mm)

213/16" (71mm)

23/8" (60mm)

Wiring: (one speaker, no counter)

Other possible applications: Offices, stores, schools, warehouse, vehicle detection, etc.

Wiring: (one speaker, with optional counter)

Wiring: (with optional counter and second speaker)

¤¤¤¤¤¤¤

Garage

door

¤¤¤¤¤¤¤¤¤¤

¤¤¤¤¤

Sample Installations:

Main

entrance

door

Reflector

Sensor Adaptor

Input

Up to 22' (7m)

Speaker

ENFORCER

DC 9V

Reflector

Sensor Adaptor

Input

Up to 22' (7m)

Speaker

ENFORCER

Counter (optional)

Output

DC 9V

Reflector

Sensor Adaptor

Input

Up to 22' (7m)

Speaker

ENFORCER

Counter (optional)

DC 9V

Speaker (optional)

ENFORCER

Input

Output

Store front door

¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤

Mounting the Reflector:

Installation and Adjustment:

Sample Fixed Mounting:

Mounting the Sensor:

Mounting the Speaker/Electronic Chime:

Sample

Fixed

Mounting:

Sample

Bracket

Mounting:

Adjusting the Speaker/Electronic Chime:

LED Functions:

RED LED - When ON, it indicates the sensor is

powered and aligned properly.

Installation:

1. Mount the reflector and sensor so they face each

other at about 2' off the ground or knee high.

2. Connect the sensor to the speaker.

3. Connect power adaptor to the speaker.

••

•For signalling in multiple rooms, add an optional

second speaker (E-931ACC-S).

••

•Connect an optional counter (E-931ACC-C) to the

speaker output (if desired).

4. To find the correct alignment, slowly adjust the

angles of the sensor and/or reflector up and down

and right and left.

NOTE:Correct alignment is reached when red LED

turns ON.

Set Speaker Mode:

After the sensor and reflector have been properly

installed, the next step is to set the speaker mode.

Choose between "Chime" or "Alarm" sound or "OFF".

2. If "Alarm" was chosen:

A. Set speaker to Alarm

B. Adjust the alarm sounding time from 3 to 30

seconds.

C. Set speaker Volume.

3. If "Chime" was chosen: Set speaker to Chime

4. If "OFF" was chosen:

A. Set speaker to OFF

B. The speaker will not sound when the beam is

broken.

Using the Optional Counter:

1. Automatically increases by "1" when sensor is

triggered.

2. Manually add "1" by pressing "+".

3. Manually subtract "1" by pressing "

4. Reset counter by pressing "RESET."

Testing:

1. Power up the sensor and speaker. The red LED

should be ON.

2. Pass object to be detected between the sensor

and reflector. The red LED should turn OFF and

the speaker (if connected) should sound.

Red LED

ENFORCER®

Switch: Chime/

OFF/Alarm

Timer: 3~30 Sec.

Volume:0 ~ max

Switch

Wall mount hole

Bracket

mounting

holes

Tabla de contenidos

Otros manuales de Sistema de seguridad de ENFORCER

ENFORCER

ENFORCER SD-7201GC-PEQ Manual de usuario

ENFORCER

ENFORCER Enforcer SD-927PKC-NEQ Manual de usuario

ENFORCER

ENFORCER E-931CS22RFCQ Manual de usuario

ENFORCER

ENFORCER E-931CS22RFCQ Manual de usuario

ENFORCER

ENFORCER E-921APQ Manual de usuario

ENFORCER

ENFORCER SD-7157-SSTQ Manual de usuario

ENFORCER

ENFORCER RINS1708-3 Manual de instalación y funcionamiento

ENFORCER

ENFORCER Enforcer Access SD-71002-V0 Manual de usuario

ENFORCER

ENFORCER E-921CPQ Manual de usuario

ENFORCER

ENFORCER SD-7113-GSP Manual de usuario

ENFORCER

ENFORCER SECO0LARM SLI RM-R100-TBQ Manual de usuario

ENFORCER

ENFORCER Enforcer 32-WE Manual de usuario

ENFORCER

ENFORCER E-931CS22RFCQ Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario