Endress+Hauser Flexdip CYH112 Manual de usuario
Products Solutions Services
Operating Instructions
Flexdip CYH112
Holder for water and wastewater assemblies
BA00430C/07/EN/14.19
71453974
2019-01-07
Flexdip CYH112 Table of contents
Endress+Hauser 3
Table of contents
1 About this document ................ 4
1.1 Warnings ............................ 4
1.2 Symbols used .......................... 4
2 Basic safety instructions ............ 5
2.1 Requirements for the personnel ............ 5
2.2 Designated use ........................ 5
2.3 Workplace safety ....................... 5
2.4 Operational safety ...................... 6
2.5 Product safety ......................... 6
3 Product description ................. 7
3.1 Product design ......................... 7
4 Incoming acceptance and product
identification ....................... 9
4.1 Incoming acceptance .................... 9
4.2 Product identification ................... 10
4.3 Scope of delivery ...................... 10
4.4 Certificates and approvals ............... 11
5 Installation ....................... 12
5.1 Installation conditions .................. 12
5.2 Mounting the holder ................... 13
5.3 Mounting options ..................... 25
5.4 Post-installation check .................. 29
6 Operation options ................. 30
6.1 Operating the pendulum holder ........... 30
7 Maintenance ...................... 31
7.1 Maintenance tasks ..................... 31
8 Repair ............................ 34
8.1 Return .............................. 34
8.2 Disposal ............................ 34
9 Accessories ....................... 35
10 Technical data .................... 40
10.1 Environment ......................... 40
10.2 Mechanical construction ................ 40
Index .................................. 44
About this document Flexdip CYH112
4 Endress+Hauser
1 About this document
1.1 Warnings
Structure of information Meaning
LDANGER
Causes (/consequences)
If necessary, Consequences of
non-compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation will result in a fatal or serious
injury.
LWARNING
Causes (/consequences)
If necessary, Consequences of
non-compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation can result in a fatal or serious
injury.
LCAUTION
Causes (/consequences)
If necessary, Consequences of
non-compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid this situation can result in minor or more serious injuries.
NOTICE
Cause/situation
If necessary, Consequences of
non-compliance (if applicable)
‣Action/note
This symbol alerts you to situations which may result in damage to
property.
1.2 Symbols used
Symbol Meaning
Additional information, tips
Permitted or recommended
Not permitted or not recommended
Reference to device documentation
Reference to page
Reference to graphic
Result of a step
1.2.1 Symbols on the device
Symbol Meaning
Reference to device documentation
Flexdip CYH112 Basic safety instructions
Endress+Hauser 5
2 Basic safety instructions
2.1 Requirements for the personnel
• Installation, commissioning, operation and maintenance of the measuring system may
be carried out only by specially trained technical personnel.
• The technical personnel must be authorized by the plant operator to carry out the
specified activities.
• The electrical connection may be performed only by an electrical technician.
• The technical personnel must have read and understood these Operating Instructions
and must follow the instructions contained therein.
• Faults at the measuring point may only be rectified by authorized and specially trained
personnel.
Repairs not described in the Operating Instructions provided must be carried out only
directly at the manufacturer's site or by the service organization.
2.2 Designated use
The assembly holder has been developed for use in the wastewater sector. CYH112 is
designed as a modular holder system for sensors and assemblies in open basins, channels
and tanks.
Use of the device for any purpose other than that described, poses a threat to the safety of
people and of the entire measuring system and is therefore not permitted.
The manufacturer is not liable for damage caused by improper or non-designated use.
NOTICE
Applications outside specifications!
Incorrect measurements, malfunctions and even measuring point failure could result
‣Use the product only in accordance with the specifications.
‣Pay attention to the technical data on the nameplate.
2.3 Workplace safety
As the user, you are responsible for complying with the following safety conditions:
• Installation guidelines
• Local standards and regulations
• Regulations for explosion protection
Basic safety instructions Flexdip CYH112
6 Endress+Hauser
2.4 Operational safety
Before commissioning the entire measuring point:
1. Verify that all connections are correct.
2. Ensure that electrical cables and hose connections are undamaged.
3. Do not operate damaged products, and protect them against unintentional operation.
4. Label damaged products as defective.
During operation:
‣If faults cannot be rectified:
products must be taken out of service and protected against unintentional operation.
2.5 Product safety
2.5.1 State-of-the-art technology
The product is designed to meet state-of-the-art safety requirements, has been tested, and
left the factory in a condition in which it is safe to operate. The relevant regulations and
international standards have been observed.
Flexdip CYH112 Product description
Endress+Hauser 7
3 Product description
3.1 Product design
1
2
3
4
5
6
A0037898
1 Example of mounted CYH112 holder
1 Base
2 Main pipe
3 Multifunctional clamp ring
4 Transverse pipe
5 Cross clamp
6 Immersion pipe of the CYA112 assembly
Product description Flexdip CYH112
8 Endress+Hauser
1
2
3
4
4
56
7
A0037909
2 Example of mounted CYH112 holder with chain
1 Base
2 Main pipe
3 Chain
4 Multifunctional clamp ring
5 Cross clamp
6 Transverse pipe
7 Immersion pipe of the CYA112 assembly
Always hook the bracket of the assembly through the last link in the chain.
Attach the holder depending on the ambient conditions.
Flexdip CYH112 Incoming acceptance and product identification
Endress+Hauser 9
4 Incoming acceptance and product
identification
4.1 Incoming acceptance
1. Verify that the packaging is undamaged.
Notify the supplier of any damage to the packaging.
Keep the damaged packaging until the issue has been resolved.
2. Verify that the contents are undamaged.
Notify the supplier of any damage to the delivery contents.
Keep the damaged goods until the issue has been resolved.
3. Check that the delivery is complete and nothing is missing.
Compare the shipping documents with your order.
4. Pack the product for storage and transportation in such a way that it is protected
against impact and moisture.
The original packaging offers the best protection.
Make sure to comply with the permitted ambient conditions.
If you have any questions, please contact your supplier or your local Sales Center.
Incoming acceptance and product identification Flexdip CYH112
10 Endress+Hauser
4.2 Product identification
4.2.1 Nameplate
The nameplate provides you with the following information on your device:
• Manufacturer identification
• Order code
• Extended order code
• Serial number
• Ambient and process conditions
• Safety information and warnings
‣Compare the information on the nameplate with the order.
4.2.2 Identifying the product
Product page
www.endress.com/cyh112
Interpreting the order code
The order code and serial number of your product can be found in the following locations:
• On the nameplate
• In the delivery papers
Obtaining information on the product
1. Go to www.endress.com.
2. Call up the site search (magnifying glass).
3. Enter a valid serial number.
4. Search.
The product structure is displayed in a popup window.
5. Click on the product image in the popup window.
A new window (Device Viewer) opens. All of the information relating to your
device is displayed in this window as well as the product documentation.
4.2.3 Manufacturer's address
Endress+Hauser Conducta GmbH+Co. KG
Dieselstraße 24
D-70839 Gerlingen
4.3 Scope of delivery
The delivery comprises:
• Ordered version of assembly holder
• Operating Instructions
‣If you have any queries:
Please contact your supplier or local sales center.
Otros manuales para Flexdip CYH112
1
Tabla de contenidos
