Endress+Hauser Solitrend MMP40 Manual de usuario

Products Solutions Services

Operating Instructions

Solitrend MMP40

Material moisture measurement

BA01936M/00/EN/02.19

71454834

2019-10-31

Solitrend MMP40

2 Endress+Hauser

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

Solitrend MMP40 Table of contents

Endress+Hauser 3

Table of contents

1 About this document ................ 4

1.1 Document function ..................... 4

1.2 Symbols used .......................... 4

1.3 Terms and abbreviations ................. 6

1.4 Documentation ........................ 6

2 Basic safety instructions ............ 7

2.1 Requirements for the personnel ............ 7

2.2 Designated use ........................ 7

2.3 Workplace safety ....................... 8

2.4 Operational safety ...................... 8

2.5 Product safety ......................... 8

3 Product description ................. 9

3.1 Product design ......................... 9

4 Incoming acceptance and product

identification ..................... 10

4.1 Incoming acceptance ................... 10

4.2 Product identification ................... 10

4.3 Manufacturer's address ................. 10

4.4 Storage, transport ..................... 10

5 Installation ....................... 11

5.1 Installation conditions .................. 11

5.2 Mounting location for round sensor, short /

middle version ........................ 11

5.3 Mounting location for round sensor, long

version ............................. 12

5.4 Mounting location for rectangular sensor .... 13

5.5 Mounting location for rod sensor .......... 13

5.6 Protection of sensor connector against

abrasion ............................ 14

5.7 Post-installation check .................. 15

6 Electrical connection .............. 16

6.1 Connection conditions .................. 16

6.2 Cable specification ..................... 18

6.3 Electrical connection - example, sensor cable

with 10-pin socket (sensor side) and ferrules

at the end of the cable .................. 19

6.4 Post-connection check .................. 19

7 Operating options ................. 20

7.1 Overview of operation options ............ 20

8 Commissioning .................... 21

8.1 Analog outputs for measured value output ... 21

8.2 Operating mode ....................... 22

8.3 Calibration curves Cal1 to Cal15 ........... 23

8.4 Special functions ...................... 24

9 Diagnostics and troubleshooting ... 26

9.1 Optimizing the material flow ............. 26

9.2 Difference between measured moisture value

and laboratory value too large during initial

commissioning ....................... 26

10 Maintenance ...................... 28

10.1 Exterior cleaning ...................... 28

11 Repair ............................ 29

11.1 General information ................... 29

11.2 Return .............................. 29

11.3 Disposal ............................ 29

12 Accessories ....................... 30

12.1 Device-specific accessories ............... 30

13 Technical data .................... 33

13.1 Input ............................... 33

13.2 Output ............................. 33

13.3 Performance characteristics .............. 33

13.4 Environment ......................... 34

13.5 Process ............................. 34

About this document Solitrend MMP40

4 Endress+Hauser

1 About this document

1.1 Document function

These Operating Instructions provide all of the information that is required in various

phases of the life cycle of the device including:

• Product identification

• Incoming acceptance

• Storage

• Installation

• Connection

• Operation

• Commissioning

• Troubleshooting

• Maintenance

• Disposal

1.2 Symbols used

1.2.1 Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

1.2.2 Symbols for certain types of information and graphics

Permitted

Procedures, processes or actions that are permitted

Preferred

Procedures, processes or actions that are preferred

Forbidden

Procedures, processes or actions that are forbidden

Tip

Indicates additional information

Reference to documentation

Reference to graphic

Solitrend MMP40 About this document

Endress+Hauser 5

Notice or individual step to be observed

Series of steps

Result of a step

1, 2, 3, ...

Item numbers

A, B, C, ...

Views

Safety instructions

Observe the safety instructions contained in the associated Operating Instructions

About this document Solitrend MMP40

6 Endress+Hauser

1.3 Terms and abbreviations

Document type "Operating Instructions"

Document type "Technical Information"

Document type "Special Documentation"

Nominal pressure

PLC

Programmable logic controller (PLC)

1.4 Documentation

The following documentation types are available in the Downloads section of the Endress

+Hauser website (www.endress.com/downloads):

For an overview of the scope of the associated Technical Documentation, refer to the

following:

•W@M Device Viewer (www.endress.com/deviceviewer): Enter the serial number

from nameplate

•Endress+Hauser Operations App: Enter the serial number from the nameplate or

scan the 2D matrix code (QR code) on the nameplate

1.4.1 Technical Information (TI)

Planning aid

The document contains all the technical data on the device and provides an overview of

the accessories and other products that can be ordered for the device.

Solitrend MMP40 Basic safety instructions

Endress+Hauser 7

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill

the following requirements:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task.

‣Are authorized by the plant owner/operator.

‣Are familiar with federal/national regulations.

‣Before starting work, read and understand the instructions in the manual and

supplementary documentation as well as the certificates (depending on the

application).

‣Follow instructions and comply with basic conditions.

The operating personnel must fulfill the following requirements:

‣Are instructed and authorized according to the requirements of the task by the facility's

owner-operator.

‣Follow the instructions in this manual.

2.2 Designated use

Application and media

The measuring device described in this manual is intended for the continuous moisture

measurement of a wide variety of materials. Because of its operating frequency of approx.

1 GHz, the device can also be used outside of closed metal vessels.

If operated outside of closed vessels, the device must be mounted in accordance with the

instructions in the "Installation" section. The operation of the devices does not present any

health risk. If the limit values specified in the "Technical data" and the conditions listed in

the manual and additional documentation are observed, the measuring device may be used

for the following measurements only:

• Measured process variables: material moisture, material conductivity and material

temperature

To ensure that the measuring device remains in proper operating condition throughout the

operating period:

‣Use the device only for media to which the process-wetted materials are sufficiently

resistant.

‣Observe the limit values in "Technical data".

Incorrect use

The manufacturer is not liable for damage caused by improper or non-designated use.

Clarification of borderline cases:

‣For special materials and media used for cleaning, the manufacturer is happy to

provide assistance in verifying the corrosion resistance of medium-wetted materials,

but disclaims any warranty or liability.

Residual risks

Due to heat transfer from the process as well as power dissipation within the electronics,

the temperature of the electronics housing and the assemblies contained therein may rise

to 70 °C (158 °F) during operation. During operation, the sensor can reach a temperature

close to the medium temperature.

Danger of burns from contact with surfaces!

‣In the event of elevated medium temperatures, ensure protection against contact to

prevent burns.

Basic safety instructions Solitrend MMP40

8 Endress+Hauser

2.3 Workplace safety

When working on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

2.4 Operational safety

Risk of injury.

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

Conversions to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers.

‣If, despite this, modifications are required, consult with the manufacturer.

Repair

To ensure continued operational safety and reliability,

‣Carry out repairs on the device only if they are expressly permitted.

‣Observe federal/national regulations pertaining to repair of an electrical device.

‣Use original spare parts and accessories from the manufacturer only.

Hazardous area

To eliminate a danger for persons or for the facility when the device is used in the

hazardous area (e.g. explosion protection, pressure vessel safety):

‣Based on the nameplate, check whether the ordered device is permitted for the

intended use in the hazardous area.

‣Observe the specifications in the separate supplementary documentation that is an

integral part of these Instructions.

2.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet

state-of-the-art safety requirements, has been tested, and left the factory in a condition in

which it is safe to operate.

It meets general safety standards and legal requirements. It also complies with the EC

directives listed in the device-specific EC Declaration of Conformity. The manufacturer

confirms this by affixing the CE mark to the device.

Solitrend MMP40 Product description

Endress+Hauser 9

3 Product description

TDR material moisture sensors for measuring bulk solids, emulsions, liquids and media

with higher material densities and conductivity values up to 20 ms/cm.

3.1 Product design

A0040142

 1 Product design

1 Measuring cell; ceramic (silicon nitride)

2 Sensor plate

3 Housing

Incoming acceptance and product identification Solitrend MMP40

10 Endress+Hauser

4 Incoming acceptance and product

identification

4.1 Incoming acceptance

Check the following during incoming acceptance:

 Are the order codes on the delivery note and the product sticker identical?

 Are the goods undamaged?

 Do the nameplate data match the ordering information on the delivery note?

 If required (see nameplate): Are the safety instructions (XA) provided?

If one of these conditions is not met, please contact the manufacturer's sales office.

4.2 Product identification

The following options are available for the identification of the measuring device:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

‣Enter the serial number from the nameplates into W@M Device Viewer

(www.endress.com/deviceviewer)

 All the information about the measuring device and the scope of the associated

Technical Documentation are displayed.

‣Enter the serial number from the nameplate into the Endress+Hauser Operations App

or use the Endress+Hauser Operations App to scan the 2-D matrix code (QR Code)

provided on the nameplate

 All the information about the measuring device and the scope of the associated

Technical Documentation are displayed.

4.3 Manufacturer's address

Endress+Hauser SE+Co. KG

Hauptstraße 1

79689 Maulburg, Germany

4.4 Storage, transport

4.4.1 Storage conditions

• Permitted storage temperature: –40 to +70 °C (–40 to +158 °F)

• Use original packaging.

4.4.2 Transporting the product to the measuring point

Transport the device to the measuring point in the original packaging.

Tabla de contenidos

Otros manuales de Instrumento de medición de Endress+Hauser

Endress+Hauser

Endress+Hauser Waterpilot FMX21 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manual de usuario

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Deltabar S PMD70 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 93 Manual de lista de piezas

Endress+Hauser

Endress+Hauser Solimotion FTR20 Manual de usuario

Endress+Hauser

Endress+Hauser Proline t-mass 65 Manual de usuario

Endress+Hauser

Endress+Hauser Proline t-mass 65 Manual de usuario

Endress+Hauser

Endress+Hauser SS500 Actualización de firmware

Endress+Hauser

Endress+Hauser Proline Promass E TB2 HART Manual de usuario

Endress+Hauser

Endress+Hauser Deltapilot S FMB70 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 55S Manual

Endress+Hauser

Endress+Hauser CUM 750 Manual de usuario

Endress+Hauser

Endress+Hauser Liquiline System CA80CR Especificaciones técnicas

Endress+Hauser

Endress+Hauser Proline Prosonic Flow P 500 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag H 200 Especificaciones técnicas

Endress+Hauser

Endress+Hauser StamoSens CNM 750 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promass 83 Especificaciones técnicas

Endress+Hauser

Endress+Hauser PROFIBUS-PA PROline promass 80 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Deltabar S FMD77 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Solicap M FTI55 Instrucciones de instalación

Endress+Hauser

Endress+Hauser Levelflex FMP51 Manual de usuario

Endress+Hauser

Endress+Hauser RIA 250 Manual de usuario

Endress+Hauser

Endress+Hauser Prothermo NMT 539 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Acterna

Acterna MS1400 Manual de usuario

R&S

R&S ZPH Manual de usuario