Endress+Hauser RIA16 Manual de usuario

Products Solutions Services

Operating Instructions

RIA16

Loop-powered field indicator

BA00280R/09/EN/06.23-00

71613276

2023-01-31

Table of contents RIA16

2 Endress+Hauser

Table of contents

1 About this document ................ 3

1.1 Symbols .............................. 3

1.2 Documentation ........................ 4

2 Basic safety instructions ............ 5

2.1 Requirements for the personnel ............ 5

2.2 Intended use .......................... 5

2.3 Workplace safety ....................... 5

2.4 Operational safety ...................... 5

2.5 Product safety ......................... 6

2.6 IT security ............................ 6

3 Incoming acceptance and product

identification ....................... 6

3.1 Incoming acceptance .................... 6

3.2 Product identification .................... 7

3.3 Storage and transport ................... 7

3.4 Certificates and approvals ................ 7

4 Mounting .......................... 8

4.1 Mounting requirements .................. 8

4.2 Mounting the measuring device ............ 9

4.3 Post-mounting checks .................. 10

5 Electrical connection .............. 10

5.1 Connecting the device .................. 11

5.2 Ensuring the degree of protection .......... 12

5.3 Post-connection check .................. 12

6 Operation options ................. 13

6.1 Overview of operation options ............ 13

6.2 Access to the operating menu via the

operating keys ........................ 13

6.3 Structure and function of the operating

menu .............................. 15

6.4 Access to the operating menu via the

operating tool ........................ 16

7 Commissioning .................... 17

7.1 Post-installation check .................. 17

7.2 Switching on the device ................. 17

7.3 Configuring the measuring device .......... 17

8 Diagnosis and troubleshooting ..... 21

8.1 General troubleshooting ................. 21

8.2 Diagnostic list ........................ 21

9 Maintenance ...................... 22

9.1 Cleaning ............................ 22

10 Repair ............................ 22

10.1 General information ................... 22

10.2 Spare parts .......................... 23

10.3 Return .............................. 24

10.4 Disposal ............................ 24

11 Accessories ....................... 24

11.1 Device-specific accessories ............... 25

11.2 Communication-specific accessories ........ 25

12 Technical data .................... 25

12.1 Input ............................... 25

12.2 Output ............................. 25

12.3 Power supply ......................... 26

12.4 Performance characteristics .............. 27

12.5 Mounting ........................... 27

12.6 Environment ......................... 27

12.7 Mechanical construction ................ 29

12.8 Human interface ...................... 29

12.9 Certificates and approvals ............... 31

12.10 Documentation ....................... 31

RIA16 About this document

Endress+Hauser 3

1 About this document

1.1 Symbols

1.1.1 Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

1.1.2 Electrical symbols

Symbol Meaning

Direct current

Alternating current

Direct current and alternating current

Ground connection

A grounded terminal which, as far as the operator is concerned, is grounded via a

grounding system.

Potential equalization connection (PE: protective earth)

Ground terminals that must be connected to ground prior to establishing any other

connections.

The ground terminals are located on the interior and exterior of the device:

• Interior ground terminal: potential equalization is connected to the supply network.

• Exterior ground terminal: device is connected to the plant grounding system.

1.1.3 Symbols for certain types of information

Symbol Meaning

Permitted

Procedures, processes or actions that are permitted.

Preferred

Procedures, processes or actions that are preferred.

Forbidden

Procedures, processes or actions that are forbidden.

Tip

Indicates additional information.

Reference to documentation

Reference to page

About this document RIA16

4 Endress+Hauser

Symbol Meaning

Reference to graphic

Notice or individual step to be observed

… Series of steps

Result of a step

Help in the event of a problem

Visual inspection

1.1.4 Symbols in graphics

Symbol Meaning Symbol Meaning

1, 2, 3,... Item numbers

… Series of steps

A, B, C, ... Views A-A, B-B, C-C, ... Sections

Hazardous area

Safe area (non-hazardous area)

1.2 Documentation

For an overview of the scope of the associated Technical Documentation, refer to the

following:

•Device Viewer (www.endress.com/deviceviewer): Enter the serial number from the

nameplate

•Endress+Hauser Operations app: Enter serial number from nameplate or scan

matrix code on nameplate.

1.2.1 Document function

The following documentation may be available depending on the version ordered:

Document type Purpose and content of the document

Technical Information (TI) Planning aid for your device

The document contains all the technical data on the device and provides

an overview of the accessories and other products that can be ordered for

the device.

Brief Operating Instructions (KA) Guide that takes you quickly to the 1st measured value

The Brief Operating Instructions contain all the essential information

from incoming acceptance to initial commissioning.

Operating Instructions (BA) Your reference document

The Operating Instructions contain all the information that is required in

the various phases of the life cycle of the device: from product

identification, incoming acceptance and storage, to mounting,

connection, operation and commissioning through to troubleshooting,

maintenance and disposal.

Description of Device Parameters

(GP)

Reference for your parameters

The document provides a detailed explanation of each individual

parameter. The description is aimed at those who work with the device

over the entire life cycle and perform specific configurations.

RIA16 Basic safety instructions

Endress+Hauser 5

Document type Purpose and content of the document

Safety Instructions (XA) Depending on the approval, safety instructions for electrical equipment in

hazardous areas are also supplied with the device. The Safety Instructions

are an integral part of the Operating Instructions.

Information on the Safety Instructions (XA) relevant to the device is

provided on the nameplate.

Supplementary device-dependent

documentation (SD/FY)

Always comply strictly with the instructions in the relevant

supplementary documentation. The supplementary documentation is an

integral part of the device documentation.

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill

the following requirements:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task.

‣Are authorized by the plant owner/operator.

‣Are familiar with federal/national regulations.

‣Before starting work, read and understand the instructions in the manual and

supplementary documentation as well as the certificates (depending on the

application).

‣Follow instructions and comply with basic conditions.

The operating personnel must fulfill the following requirements:

‣Are instructed and authorized according to the requirements of the task by the facility's

owner-operator.

‣Follow the instructions in this manual.

2.2 Intended use

• The device is a configurable field indicator with one sensor input.

• It is designed for mounting in the field.

• The manufacturer accepts no liability for damages resulting from improper or non-

intended use.

• Safe operation is only guaranteed if the Operating Instructions are observed.

• Only operate the device in the permitted temperature range.

2.3 Workplace safety

When working on and with the device:

‣Wear the required personal protective equipment as per national regulations.

2.4 Operational safety

Damage to the device!

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for the interference-free operation of the device.

Incoming acceptance and product identification RIA16

6 Endress+Hauser

Modifications to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers!

‣If modifications are nevertheless required, consult with the manufacturer.

Repair

To ensure continued operational safety and reliability:

‣Carry out repairs on the device only if they are expressly permitted.

‣Observe federal/national regulations pertaining to the repair of an electrical device.

‣Use only original spare parts and accessories.

2.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet

state-of-the-art safety requirements, has been tested, and left the factory in a condition in

which it is safe to operate.

It meets general safety standards and legal requirements. It also complies with the EU

directives listed in the device-specific EU Declaration of Conformity. The manufacturer

confirms this by affixing the CE mark to the device.

2.6 IT security

Our warranty is valid only if the product is installed and used as described in the Operating

Instructions. The product is equipped with security mechanisms to protect it against any

inadvertent changes to the settings.

IT security measures, which provide additional protection for the product and associated

data transfer, must be implemented by the operators themselves in line with their security

standards.

3 Incoming acceptance and product

identification

3.1 Incoming acceptance

Proceed as follows on receipt of the device:

1. Check whether the packaging is intact.

2. If damage is discovered:

Report all damage immediately to the manufacturer.

3. Do not install damaged components, as the manufacturer cannot otherwise

guarantee the material resistance or compliance with the original safety

requirements, and can also not be held responsible for the consequences that may

result.

4. Compare the scope of delivery against the contents of your order.

5. Remove all the packaging material used for transportation.

6. Do the data on the nameplate match the ordering information on the delivery note?

7. Are the technical documentation and all other necessary documents provided, e.g.

certificates?

If one of the conditions is not satisfied, contact your Sales Center.

RIA16 Incoming acceptance and product identification

Endress+Hauser 7

3.2 Product identification

The following options are available for identification of the device:

• Nameplate specifications

• Enter the serial number from the nameplate in the Device Viewer

(www.endress.com/deviceviewer): all the information about the device and an overview

of the Technical Documentation supplied with the device are displayed.

• Enter the serial number on the nameplate into the Endress+Hauser Operations App or

scan the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser

Operations App: all the information about the device and the technical documentation

pertaining to the device is displayed.

3.2.1 Nameplate

The right device?

The nameplate provides you with the following information on the device:

• Manufacturer identification, device designation

• Order code

• Extended order code

• Serial number

• Tag name (TAG)

• Technical values: supply voltage, current consumption, ambient temperature,

communication-specific data (optional)

• Degree of protection

• Approvals with symbols

‣Compare the information on the nameplate with the order.

3.2.2 Name and address of manufacturer

Name of manufacturer: Endress+Hauser Wetzer GmbH + Co. KG

Address of manufacturer: Obere Wank 1, D-87484 Nesselwang or www.endress.com

3.3 Storage and transport

Storage temperature: –40 to +80 °C (–40 to +176 °F)

Maximum relative humidity: < 95 % as per IEC 60068-2-30

Pack the device for storage and transportation in such a way that it is reliably

protected against impact and external influences. The original packaging offers the

best protection.

Avoid the following environmental influences during storage:

• Direct sunlight

• Proximity to hot objects

• Mechanical vibration

• Aggressive media

3.4 Certificates and approvals

Current certificates and approvals for the product are available at www.endress.com on the

relevant product page:

1. Select the product using the filters and search field.

2. Open the product page.

3. Select Downloads.

Mounting RIA16

8 Endress+Hauser

3.4.1 UL approval

More information under UL Product iq™, search for keyword "E225237")

4 Mounting

4.1 Mounting requirements

The device is designed for use in the field.

Its orientation is determined by the readability of the display.

Operating temperature range:

• –40 to +80 °C (–40 to +176 °F)

• –20 to +80 °C (–4 to +176 °F) when the Open Collector output is used

Operating the device in the upper temperature limit range reduces the operating life

of the display.

The display may respond slowly at temperatures < –20 °C (–4 °F).

Readability of the display can no longer be guaranteed at temperatures

< –30 °C (–22 °F).

Operating altitude Up to 2 000 m (6 561.7 ft) above sea level

Overvoltage category Overvoltage category II

Pollution degree Pollution degree 2

4.1.1 Dimensions

The dimensions of the device are provided in the "Technical data" section of the Operating

Instructions.

133 (5.24)

199 (7.83)

96 (3.78)

158 (6.22)

115 (4.53)

163 (6.42)

A-A

A0011162

 1 Dimensions of the field indicator; dimension in mm (in)

1 Bore hole for mounting directly to wall or optional mounting plate with 4 screws ⌀ 5 mm (0.2 in)

4.1.2 Mounting location

For information on the conditions that must be present at the mounting location before

the device can be mounted correctly (such as ambient temperature, type of protection,

climate class etc.), see the "Technical data" section.

RIA16 Mounting

Endress+Hauser 9

4.2 Mounting the measuring device

The device can either be mounted directly to the wall or mounted to the pipe or wall using

the optional mounting kit.

4.2.1 Direct wall mounting

To mount the indicator directly on the wall:

1. Drill 4 holes (see dimensions, →  1,  8)

2. Attach the device to the wall using 4 screws ⌀5 mm (0.2 in).

4.2.2 Pipe mounting

The mounting bracket is suitable for pipes with a diameter of 25 to 125 mm (1 to 5 in).

The mounting kit comprises a mounting plate (item 1), 2 metal strips (item 2) and 4

screws (item 3), →  2,  9.

To mount the indicator on a pipe:

1. 2.

A0011269

 2 Preparing for mounting

3mm

3. 4.

A0011270

 3 Attaching the indicator to the mounting plate

Electrical connection RIA16

10 Endress+Hauser

4.3 Post-mounting checks

Perform the following checks after mounting the device:

Device condition and specifications Note

Is the measuring device damaged? Visual inspection

Is the seal undamaged? Visual inspection

Is the device firmly screwed to the wall or mounting plate? -

Is the housing cover securely fitted? -

Does the device comply with the measuring point specifications (ambient

temperature, measuring range etc.)?

See "Technical data'

section".

5 Electrical connection

For information on the connection data, see the "Technical data" section.

NOTICE

Destruction or malfunction of parts of the electronics

‣ ESD - Electrostatic discharge. Protect the terminals from electrostatic discharge.

LCAUTION

Destruction of parts of the electronics

‣Switch off the power supply before installing and connecting the device.

NOTICE

Loss of Ex approval in case of improper connection.

‣When connecting devices certified for use in hazardous areas, ensure compliance with

all relevant instructions and connection schematics in the Ex-specific supplement to

these Operating Instructions.

First open the device housing.

A0011271

 4 Opening the field indicator housing

Otros manuales para RIA16

Tabla de contenidos

Otros manuales de Instrumento de medición de Endress+Hauser

Endress+Hauser

Endress+Hauser QWX43 Manual del operador

Endress+Hauser

Endress+Hauser Cerabar S PMP72 Manual de usuario

Endress+Hauser

Endress+Hauser nivotester FTL 325 P Instrucciones de uso

Endress+Hauser

Endress+Hauser Liquiline CA80FE Especificaciones técnicas

Endress+Hauser

Endress+Hauser SpectraSensors SS2100i-1 Manual de instrucciones

Endress+Hauser

Endress+Hauser levelflex M FMP 40 Manual de usuario

Endress+Hauser

Endress+Hauser Liquiphant M/S with electronic Insert FEL56 Manual del operador

Endress+Hauser

Endress+Hauser Flowfit CUA252 Manual de usuario

Endress+Hauser

Endress+Hauser Memobase Plus CYZ71D Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar S FMD78 Manual de usuario

Endress+Hauser

Endress+Hauser Promass 40 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50H Manual

Endress+Hauser

Endress+Hauser Liquicap M FMI51 Manual de usuario

Endress+Hauser

Endress+Hauser LT5 Manual de usuario

Endress+Hauser

Endress+Hauser Levelflex FMP56 Manual

Endress+Hauser

Endress+Hauser Cerabar M PMC41 Manual de usuario

Endress+Hauser

Endress+Hauser Prosonic M FMU40 Manual de usuario

Endress+Hauser

Endress+Hauser Liquicap M FTI51 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promass 83 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag H 200 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Micropilot FMR67 Manual

Endress+Hauser

Endress+Hauser PROFIBUS PA Especificaciones técnicas

Endress+Hauser

Endress+Hauser Liquiline CA80SI Manual de usuario

Endress+Hauser

Endress+Hauser Tankvision Gauge Link NXA20 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Acterna

Acterna MS1400 Manual de usuario

R&S

R&S ZPH Manual de usuario