Endress+Hauser Memosens Wave CAS80E Manual de usuario
Products Solutions Services
Operating Instructions
Memosens Wave CAS80E
Spectrometer for water analysis
BA02005C/07/EN/03.20
71508624
2020-12-02
Memosens Wave CAS80E Table of contents
Endress+Hauser 3
Table of contents
1 About this document ................ 4
1.1 Warnings ............................ 4
1.2 Symbols used .......................... 4
2 Basic safety instructions ............ 5
2.1 Requirements for personnel ............... 5
2.2 Designated use ........................ 5
2.3 Workplace safety ....................... 5
2.4 Operational safety ...................... 5
2.5 Product safety ......................... 6
3 Product description ................. 7
3.1 Product design ......................... 7
4 Incoming acceptance and product
identification ....................... 9
4.1 Incoming acceptance .................... 9
4.2 Product identification .................... 9
4.3 Scope of delivery ...................... 10
4.4 Certificates and approvals ............... 10
5 Installation ....................... 11
5.1 Installation conditions .................. 11
5.2 Mounting the spectrometer .............. 13
5.3 Post-installation check .................. 21
6 Electrical connection .............. 22
6.1 Connecting the spectrometer ............. 22
6.2 Ensuring the degree of protection .......... 23
6.3 Post-connection check .................. 23
7 Commissioning .................... 25
7.1 Function check ....................... 25
8 Operation ......................... 26
8.1 Adapting the measuring device to the process
conditions ........................... 26
8.2 Cyclic cleaning ........................ 29
9 Diagnostics and troubleshooting ... 31
9.1 General troubleshooting ................. 31
10 Maintenance ...................... 32
10.1 Maintenance schedule .................. 32
10.2 Maintenance tasks ..................... 32
11 Repair ............................ 34
11.1 General information ................... 34
11.2 Spare parts .......................... 34
11.3 Return .............................. 34
11.4 Disposal ............................ 34
12 Accessories ....................... 35
12.1 Device-specific accessories ............... 35
13 Technical data .................... 37
13.1 Input ............................... 37
13.2 Performance characteristics .............. 38
13.3 Environment ......................... 42
13.4 Process ............................. 42
13.5 Mechanical construction ................ 42
Index .................................. 43
About this document Memosens Wave CAS80E
4 Endress+Hauser
1 About this document
1.1 Warnings
Structure of information Meaning
LDANGER
Causes (/consequences)
If necessary, Consequences of
non-compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation will result in a fatal or serious
injury.
LWARNING
Causes (/consequences)
If necessary, Consequences of
non-compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation can result in a fatal or serious
injury.
LCAUTION
Causes (/consequences)
If necessary, Consequences of
non-compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid this situation can result in minor or more serious injuries.
NOTICE
Cause/situation
If necessary, Consequences of
non-compliance (if applicable)
‣Action/note
This symbol alerts you to situations which may result in damage to
property.
1.2 Symbols used
Symbol Meaning
Additional information, tips
Permitted or recommended
Not permitted or not recommended
Reference to device documentation
Reference to page
Reference to graphic
Result of a step
1.2.1 Symbols on the device
Symbol Meaning
Reference to device documentation
Memosens Wave CAS80E Basic safety instructions
Endress+Hauser 5
2 Basic safety instructions
2.1 Requirements for personnel
• Installation, commissioning, operation and maintenance of the measuring system may
be carried out only by specially trained technical personnel.
• The technical personnel must be authorized by the plant operator to carry out the
specified activities.
• The electrical connection may be performed only by an electrical technician.
• The technical personnel must have read and understood these Operating Instructions
and must follow the instructions contained therein.
• Faults at the measuring point may only be rectified by authorized and specially trained
personnel.
Repairs not described in the Operating Instructions provided must be carried out only
directly at the manufacturer's site or by the service organization.
2.2 Designated use
The spectrometer is used to measure a variety of parameters in liquid media with UV-VIS
spectroscopy.
The spectrometer is particularly suitable for measurements in the following applications:
• Inlet and outlet of wastewater treatment plants
• Drinking water
• Surface water
Use of the device for any purpose other than that described, poses a threat to the safety of
people and of the entire measuring system and is therefore not permitted.
The manufacturer is not liable for damage caused by improper or non-designated use.
2.3 Workplace safety
LCAUTION
UV light
UV light can damage the eyes and skin!
‣Never look into the measuring gap while the device is in operation.
As the user, you are responsible for complying with the following safety conditions:
• Installation guidelines
• Local standards and regulations
Electromagnetic compatibility
• The product has been tested for electromagnetic compatibility in accordance with the
applicable international standards for industrial applications.
• The electromagnetic compatibility indicated applies only to a product that has been
connected in accordance with these Operating Instructions.
2.4 Operational safety
Before commissioning the entire measuring point:
1. Verify that all connections are correct.
2. Ensure that electrical cables and hose connections are undamaged.
3. Do not operate damaged products, and protect them against unintentional operation.
4. Label damaged products as defective.
Basic safety instructions Memosens Wave CAS80E
6 Endress+Hauser
During operation:
‣If faults cannot be rectified:
products must be taken out of service and protected against unintentional operation.
2.5 Product safety
The product is designed to meet state-of-the-art safety requirements, has been tested, and
left the factory in a condition in which it is safe to operate. The relevant regulations and
international standards have been observed.
Memosens Wave CAS80E Product description
Endress+Hauser 7
3 Product description
3.1 Product design
The spectrometer has a diameter of 40 mm (1.57 in) and can be operated directly in-line
without any additional sampling. It is available with the standard measurement gap
lengths of 2 mm (0.08 in), 10 mm (0.4 in) and 50 mm (1.97 in), and is also available with
1 mm (0.04 in) and 100 mm (3.94 in) gap lengths on request.
The spectrometer consists of the following modules:
• Power supply
• High-voltage generation for the strobe lamp
• Xenon strobe lamp
• Monitor diode
• Measurement gap
• Spectrometer: UV/VIS 200 to 800 nm
• Microcontroller
All data - including the calibration data - are stored in the spectrometer. The spectrometer
can be precalibrated and used at a measuring point, calibrated externally, or used for
several measuring points with different calibrations.
1234
5
A0042866
1 Product design
1 Spectrometer module
2 Lens
3 Monitor diode
4 Light source
5 Measurement gap
A light source sends a beam of light through the medium via the lenses. The medium
under analysis is located in the measurement gap. In the spectrometer module, the beam
of light is converted to electrical, measurable signals → 1, 7.
3.1.1 Measuring principle
The spectrometer uses the substance-specific absorption of electromagnetic radiation to
indicate the measurement parameters from the recorded spectrum.
Product description Memosens Wave CAS80E
8 Endress+Hauser
200 300 400 500 600 700
A
λ/nm
3
12
800
a
BC
A0042861
2 Ranges of parameters in the absorption spectrum
λ Wavelength range
A Absorption
B Ultraviolet light (UV)
C Visible light (VIS)
a 254 nm, SAC
1 Nitrate, nitrite
2 Sum parameters BODeq, CODeq, TOCeq, DOCeq
3 Color, turbidity, TSS
A specific absorption spectrum can be assigned to every molecule. By comparing a zero
spectrum I0 determined previously in ultrapure water and the measuring spectrum with
the intensity I, the absorption A can be calculated as follows:
A = -log10 (I/I0) = ε . c . d
The absorption A depends directly on the concentration c, the measurement gap length d
and the extinction coefficient ε.
Analytical models programmed into the spectrometer calculate the concentration of the
parameters from the absorption spectra. These analytical models have been determined by
correlating known parameter concentrations with their related absorption spectra.
The calculation uses the same wavelengths to determine different parameters. This results
in what are termed "cross-sensitivities". For example, if turbidity increases less light is
detected when determining the chemical oxygen demand (COD).
Memosens Wave CAS80E Incoming acceptance and product identification
Endress+Hauser 9
4 Incoming acceptance and product
identification
4.1 Incoming acceptance
1. Verify that the packaging is undamaged.
Notify the supplier of any damage to the packaging.
Keep the damaged packaging until the issue has been resolved.
2. Verify that the contents are undamaged.
Notify the supplier of any damage to the delivery contents.
Keep the damaged goods until the issue has been resolved.
3. Check that the delivery is complete and nothing is missing.
Compare the shipping documents with your order.
4. Pack the product for storage and transportation in such a way that it is protected
against impact and moisture.
The original packaging offers the best protection.
Make sure to comply with the permitted ambient conditions.
If you have any questions, please contact your supplier or your local Sales Center.
4.2 Product identification
4.2.1 Nameplate
The nameplate provides you with the following information on your device:
• Manufacturer identification
• Extended order code
• Serial number
• Safety information and warnings
‣Compare the information on the nameplate with the order.
4.2.2 Identifying the product
Product page
www.endress.com/cas80e
Order code
The order code and serial number of your product can be found in the following locations:
• On the nameplate
• In the delivery papers
Obtaining information on the product
1. Go to www.endress.com.
2. Call up the site search (magnifying glass).
3. Enter a valid serial number.
4. Search.
The product structure is displayed in a popup window.
Incoming acceptance and product identification Memosens Wave CAS80E
10 Endress+Hauser
5. Click on the product image in the popup window.
A new window (Device Viewer) opens. All of the information relating to your
device is displayed in this window as well as the product documentation.
4.2.3 Manufacturer address
Endress+Hauser Conducta GmbH+Co. KG
Dieselstraße 24
D-70839 Gerlingen
4.3 Scope of delivery
The delivery comprises:
• Spectrometer, version as ordered
• Cleaning brush (x 2)
• 32GB SD card for data logging
• Operating Instructions
4.4 Certificates and approvals
4.4.1 mark
The product meets the requirements of the harmonized European standards. As such, it
complies with the legal specifications of the EU directives. The manufacturer confirms
successful testing of the product by affixing to it the mark.
4.4.2 Additional certification
Electromagnetic compatibility
Interference emission and interference immunity as per
• EN 61326-1:2013
• EN 61326-2-3:2013
• EN 61326-2-5: 2013
• NAMUR NE21: 2012
Tabla de contenidos
Otros manuales de Instrumento de medición de Endress+Hauser
Endress+Hauser
Endress+Hauser nivotester FTL 325 P Instrucciones de uso
Endress+Hauser
Endress+Hauser Proline Fieldcheck Manual de usuario
Endress+Hauser
Endress+Hauser Topcal S CPC310 Manual de usuario
Endress+Hauser
Endress+Hauser Liquiline M CM42 Manual
Endress+Hauser
Endress+Hauser Proline Promag W 400 Especificaciones técnicas
Endress+Hauser
Endress+Hauser Levelflex FMP56 Manual de usuario
Endress+Hauser
Endress+Hauser Levelflex FMP50 Instrucciones de instalación
Endress+Hauser
Endress+Hauser Micropilot FMR60 Instrucciones de instalación
Endress+Hauser
Endress+Hauser Proline t-mass B 150 HART Manual de usuario
Endress+Hauser
Endress+Hauser ria45 Especificaciones técnicas
Endress+Hauser
Endress+Hauser Proline Prosonic Flow B 200 Especificaciones técnicas
Endress+Hauser
Endress+Hauser Soliwave FQR56 Manual de usuario
Endress+Hauser
Endress+Hauser prowirl 70 Manual
Endress+Hauser
Endress+Hauser Liquiline CM44 series Manual del operador
Endress+Hauser
Endress+Hauser Proline t-mass T 150 Manual de usuario
Endress+Hauser
Endress+Hauser Proline Promag 300 Guía de aplicación
Endress+Hauser
Endress+Hauser Proline Promag 50 Series Manual del operador
Endress+Hauser
Endress+Hauser Tank Side Monitor NRF590 Manual
Endress+Hauser
Endress+Hauser Promass 40 Manual de usuario
Endress+Hauser
Endress+Hauser Proline Promag W 500 Manual de usuario
