Endress+Hauser Liquistation CSF39 Especificaciones técnicas
Products Solutions Services
Brief Operating Instructions
Liquistation CSF39
Automatic sampler for liquid media
These Instructions are Brief Operating Instructions; they are
not a substitute for the Operating Instructions pertaining to
the device.
Detailed information on the device can be found in the
Operating Instructions and in the other documentation
available at:
• www.endress.com/device-viewer
• Smart phone/tablet: Endress+Hauser Operations App
KA01184C/07/EN/02.16
71314891
Valid as of version
01.06.00
Liquistation CSF39
2 Endress+Hauser
TAG No.: XXX000
Ser. No.: X000X000000
Order code 00X00-XXXX0XX0XXX
www.endress.com/deviceviewer Endress+Hauser Operations App
Serial number
A0023555
Liquistation CSF39 Table of contents
Endress+Hauser 3
Table of contents
1 Document information ........................................................... 4
1.1 Warnings ........................................................................... 4
1.2 Symbols ............................................................................ 4
1.3 Symbols at the device ................................................................... 4
1.4 Documentation ....................................................................... 5
2 Basic safety instructions ......................................................... 6
2.1 Requirements for the personnel ........................................................... 6
2.2 Designated use ....................................................................... 6
2.3 Occupational safety .................................................................... 6
2.4 Operational safety ..................................................................... 7
2.5 Product safety ........................................................................ 7
3 Incoming acceptance and product identification .................................. 8
3.1 Incoming acceptance ................................................................... 8
3.2 Product identification .................................................................. 8
3.3 Scope of delivery ...................................................................... 9
3.4 Certificates and approvals ............................................................... 9
4 Installation ..................................................................... 10
4.1 Installation conditions ................................................................. 10
4.2 Installation ......................................................................... 16
4.3 Post-installation check ................................................................. 18
5 Electrical connection ............................................................ 19
5.1 Connecting the sampler ................................................................ 19
5.2 Connecting modules and sensors ......................................................... 25
5.3 Terminal assignment for input/output signals ............................................... 35
5.4 Connecting additional inputs, outputs or relays ............................................... 36
5.5 Connecting digital communication ........................................................ 38
5.6 Hardware settings .................................................................... 41
5.7 Ensuring the degree of protection ........................................................ 42
5.8 Post-connection check ................................................................. 43
6 Operation options .............................................................. 44
6.1 Overview ........................................................................... 44
6.2 Access to the operating menu via the local display ............................................ 45
6.3 Configuration options ................................................................. 46
7 Commissioning ................................................................. 50
7.1 Function check ...................................................................... 50
7.2 Switching on ........................................................................ 50
7.3 Basic setup ......................................................................... 51
7.4 Sampling programs ................................................................... 52
Document information Liquistation CSF39
4 Endress+Hauser
1 Document information
1.1 Warnings
Structure of information Meaning
LDANGER
Causes (/consequences)
Consequences of non-compliance (if
applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation will result in a fatal or serious injury.
LWARNING
Causes (/consequences)
Consequences of non-compliance (if
applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation can result in a fatal or serious injury.
LCAUTION
Causes (/consequences)
Consequences of non-compliance (if
applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid this situation can result in minor or more serious injuries.
NOTICE
Cause/situation
Consequences of non-compliance (if
applicable)
‣Action/note
This symbol alerts you to situations which may result in damage to property.
1.2 Symbols
Symbol Meaning
Additional information, tips
Permitted or recommended
Not permitted or not recommended
Reference to device documentation
Reference to page
Reference to graphic
Result of a step
1.3 Symbols at the device
Symbol Meaning
Reference to device documentation
Liquistation CSF39 Document information
Endress+Hauser 5
1.4 Documentation
The following manuals which are available on the product pages on the internet complement
these Operating Instructions:
• Operating Instructions for
– Device description
– Commissioning
– Operation
– Software description (excluding sensor menus; these are described in a separate manual -
see below)
– Device-specific diagnostics and troubleshooting
– Maintenance
– Repair and spare parts
– Accessories
– Technical data
• Operating Instructions for Memosens, BA01245C
– Software description for Memosens inputs
– Calibration of Memosens sensors
– Sensor-specific diagnostics and troubleshooting
• Operating Instructions for HART communication, BA00486C
– Onsite settings and installation instructions for HART
– Description of HART driver
• Guidelines for communication via fieldbus and web server
– HART, SD01187C
– PROFIBUS, SD01188C
– Modbus, SD01189C
– Web server, SD01190C
– Web server (optional), SD01190C
– EtherNet/IP, SD01293C
• Special Documentation: Sampler application manual SD01068C
• Documentation on other devices in the Liquiline platform:
– Liquiline CM44xR (DIN rail device)
– Liquiline System CA80 (analyzer)
– Liquiline System CAT8x0 (sample preparation)
– Liquistation CSFxx (sampler)
– Liquiport CSP44 (sampler)
Basic safety instructions Liquistation CSF39
6 Endress+Hauser
2 Basic safety instructions
2.1 Requirements for the personnel
• Installation, commissioning, operation and maintenance of the measuring system may be
carried out only by specially trained technical personnel.
• The technical personnel must be authorized by the plant operator to carry out the specified
activities.
• The electrical connection may be performed only by an electrical technician.
• The technical personnel must have read and understood these Operating Instructions and
must follow the instructions contained therein.
• Measuring point faults may be repaired only by authorized and specially trained personnel.
Repairs not described in the Operating Instructions provided may only be carried out
directly by the manufacturer or by the service organization.
2.2 Designated use
Liquistation CSF39 is a stationary sampler for liquid media. The samples are taken
discontinuously using a vacuum pump or peristaltic pump and are then distributed into
sampling containers and refrigerated.
The sampler is designed for use in the following applications:
• Communal and industrial wastewater treatment plants
• Laboratories and water management offices
• Monitoring of liquid media in industrial processes
Use of the device for any purpose other than that described, poses a threat to the safety of
people and of the entire measuring system and is therefore not permitted. The manufacturer
is not liable for damage caused by improper or non-designated use.
2.3 Occupational safety
As the user, you are responsible for complying with the following safety conditions:
• Installation guidelines
• Local standards and regulations
Electromagnetic compatibility
• The product has been tested for electromagnetic compatibility in accordance with the
applicable European standards for industrial applications.
• The electromagnetic compatibility indicated applies only to a product that has been
connected in accordance with these Operating Instructions.
Liquistation CSF39 Basic safety instructions
Endress+Hauser 7
2.4 Operational safety
1. Before commissioning the entire measuring point, verify that all connections are
correct. Ensure that electrical cables and hose connections are undamaged.
2. Do not operate damaged products, and safeguard them to ensure that they are not
operated inadvertently. Label the damaged product as defective.
3. If faults cannot be rectified:
Take the products out of operation and safeguard them to ensure that they are not
operated inadvertently.
LCAUTION
Cleaning not switched off during calibration or maintenance activities
Risk of injury due to medium or cleaning agent
‣If a cleaning system is connected, switch if off before removing a sensor from the medium.
‣If you wish to check the cleaning function and have therefore not switched off the cleaning
system, please wear protective clothing, goggles and gloves or take other appropriate
measures.
2.5 Product safety
2.5.1 State of the art
The product is designed to meet state-of-the-art safety requirements, has been tested, and
left the factory in a condition in which it is safe to operate. The relevant regulations and
European standards have been observed.
Devices connected to the sampler must comply with the applicable safety standards.
2.5.2 IT security
We only provide a warranty if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any
inadvertent changes to the device settings.
IT security measures in line with operators' security standards and designed to provide
additional protection for the device and device data transfer must be implemented by the
operators themselves.
Incoming acceptance and product identification Liquistation CSF39
8 Endress+Hauser
3 Incoming acceptance and product identification
3.1 Incoming acceptance
1. Verify that the packaging is undamaged.
Notify your supplier of any damage to the packaging.
Keep the damaged packaging until the matter has been settled.
2. Verify that the contents are undamaged.
Notify your supplier of any damage to the delivery contents.
Keep the damaged products until the matter has been settled.
3. Check the delivery for completeness.
Check it against the delivery papers and your order.
4. Pack the product for storage and transportation in such a way that it is protected
against impact and moisture.
The original packaging offers the best protection.
The permitted ambient conditions must be observed (see "Technical data").
If you have any questions, please contact your supplier or your local sales center.
NOTICE
Damage to the sampler
If transported incorrectly, the roof may become damaged or tear off.
‣Transport the sampler using a forklift truck. Never lift the sampler by the top. Lift it in the
middle between the upper and lower sections.
3.2 Product identification
Nameplates can be found:
• On the inside of the door
• On the packaging (adhesive label, portrait format)
3.2.1 Nameplate
The nameplate provides you with the following information on your device:
• Manufacturer identification
• Order code
• Extended order code
• Serial number
• Firmware version
• Ambient and process conditions
• Input and output values
• Activation codes
• Safety information and warnings
‣Compare the data on the nameplate with your order.
Liquistation CSF39 Incoming acceptance and product identification
Endress+Hauser 9
3.3 Scope of delivery
The scope of delivery comprises:
• 1 Liquistation CSF39 with:
– The ordered bottle configuration
– Optional hardware
• Accessories kit
For peristaltic or vacuum pump:
Connection nipple for suction line with various angles (straight, 90°), Allen key (for version
with vacuum pump only)
• 1 print version of Brief Operating Instructions in the language ordered
• Optional accessories
If you have any questions, please contact your supplier or your local sales center.
3.4 Certificates and approvals
3.4.1 mark
Declaration of Conformity
The product meets the requirements of the harmonized European standards. As such, it
complies with the legal specifications of the EC directives. The manufacturer confirms
successful testing of the product by affixing to it the mark.
Installation Liquistation CSF39
10 Endress+Hauser
4 Installation
4.1 Installation conditions
4.1.1 Dimensions
355 (14.0)
125 (4.9)
903 (35.6)
1508 (59.3)
625 (24.6)
471 (18.5)
816 (32.1)
753 (29.7)
A
A
250 (9.8)
A0024494
1 Dimensions of Liquistation CSF39 plastic version with stand, dimensions in mm (in)
A Suction line connection
Otros manuales para Liquistation CSF39
2
Tabla de contenidos
Otros manuales de Equipo de laboratorio de Endress+Hauser
Endress+Hauser
Endress+Hauser Liquistation CSF48 Manual de usuario
Endress+Hauser
Endress+Hauser Analytik Jena UVP Minidizer Manual
Endress+Hauser
Endress+Hauser Liquistation CSF33 Manual de usuario
Endress+Hauser
Endress+Hauser analytikjena CyBio QuadPrint HQ-M Manual de usuario
Endress+Hauser
Endress+Hauser Liquistation CSF48 Manual de usuario
Endress+Hauser
Endress+Hauser Analytik Jena CyBio FeliX Manual de usuario
Endress+Hauser
Endress+Hauser Levelflex FMP51 Instrucciones de instalación
Endress+Hauser
Endress+Hauser Chemoclean CYR10B Manual de usuario
Endress+Hauser
Endress+Hauser Liquistation CSF34 Manual de usuario
Endress+Hauser
Endress+Hauser CPY7 Manual de usuario
Endress+Hauser
Endress+Hauser Liquistation CSF48 Manual
Endress+Hauser
Endress+Hauser ASP Station 2000 Manual de usuario
Endress+Hauser
Endress+Hauser Analytik Jena APUsim Manual de usuario
Endress+Hauser
Endress+Hauser Analytik Jena CyBio SELMA Manual de usuario
Endress+Hauser
Endress+Hauser Analytik Jena multi N/C Manual de usuario
Endress+Hauser
Endress+Hauser Analytik Jena PlasmaQuant PQ 9000 Manual de usuario
Endress+Hauser
Endress+Hauser Analytik Jena Biometra TSC ThermoShaker Manual de usuario
Endress+Hauser
Endress+Hauser OXY5500 QF Actualización de firmware
Endress+Hauser
Endress+Hauser analytikjena qTOWER Manual de usuario
Endress+Hauser
Endress+Hauser ISEmax CAM40 Manual de usuario
Manuales populares de Equipo de laboratorio de otras marcas
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manual de usuario
NI
NI PXI-5422 Manual
Collomix
Collomix Aqix Manual de usuario
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario
Ocean Insight
Ocean Insight FLAME-NIR+ Manual de usuario
Parker
Parker ALIGN-MG-NA Manual de usuario
