Enclume HDR3 Manual de instrucciones

Boot and Mitten Drying Rack

ModelHDR3

WARNING:

The parts and hardware included are:

Hardware parts:

6 – 5/16"x 1/2"Button Head Screws

4 – 5/16"x 3/8"Button Head Screws

1 – 3/16"Allen Wrench

4 – Hard Glides

Components:

2 – Legs

2 – Boot Holders

2 – Uprights

1 – Upper Crossbar

4 – Accessory Hooks

See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS

Assembly and Installation Instructions for the Hearth Drying Rack HDR3

Limited Warranty: This product is warranted to be free of material defects for a period of five years from the date of purchase. Your exclusive remedy shall be

the repair or replacement of the defective product, which shall be subject to the following conditions: (1) Your notice of a defect is received by Enclume within the

warranty period, and (2) your return of the defective product to Enclume Design Products (24 Colwell St. , Port Hadlock, WA 98339) postage prepaid within 20

days following your receipt of a return authorization number from Enclume (which may be obtained by telephoning the number at the bottom of these instructions).

There are no other warranties, expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, AND ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF

THE PURCHASE OR USE OF THIS PRODUCT.

Enclume racks are the ultimate in Quality,

design, strength and function. Congratulations

for owning one of the finest storage racks

made.

Enclosed your will find everything needed

for the assembly and use of your hearth

rack.

READ ALL OF THE INSTRUCTIONS BEFORE

ASSEMBLING AND USING YOUR RACK.

If you need help, please call 1-877-362-5863 or email

[email protected].

Rack Assembly: (Please note: Do not tighten the screws completely until rack is fully assembled)

1) Locate the legs and insert each end into one of the 4 hard glides. Then place the legs on the floor hard

glides down.

2) Place a boot holder cross wise on one end of the legs, align the holes and with the 5/16"x 1/2"button

head screws, attach to legs. Repeat on the other side.

3) Place one upright cross wise on one of the center holes with the L facing out and the tall side in the

center. Attach with one of the 5/16"x 1/2"button head screws. Repeat on the other side.

4) Place Top Cross bar between the 2 uprights and place the 5/16"x 1/2"button head screw through both

uprights and the cross bar.

5) Attach the 4 accessory hooks (2 on each side) with the 5/16"x 3/8"button head screws.

6) Square up the rack and tighten the screws securely.

7) Our hammered steel racks are finished with an industrial wax designed to give years of protection to the

rack. Cleaning is easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is ever

needed we recommend a commercial wax product.

WARNING

It is important that your rack is assembled correctly. If the unit is assembled

or used incorrectly, it could become unstable and collapse, possibly causing

injury. Please use caution when drying clothing near a fire source. Fabrics

are combustible and could ignite.

Enclume Designs LLC •24 Colwell Street •Port Hadlock, WA 98339 •360.385.6100 • www.enclume.com

Otros manuales de Rack y soporte de Enclume

Enclume

Enclume PR2 Manual de usuario

Enclume

Enclume Decor DR23 Manual de usuario

Enclume

Enclume PR33 Manual de instrucciones

Enclume

Enclume PR13 Manual de usuario

Enclume

Enclume LR32 Manual de usuario

Enclume

Enclume Square Pot Rack Manual de usuario

Enclume

Enclume LR2T Manual de usuario

Enclume

Enclume DR 25 Manual de usuario

Enclume

Enclume QR3 Manual de usuario

Enclume

Enclume DR18-Decor Manual de instrucciones

Enclume

Enclume PR35 Manual de instrucciones

Enclume

Enclume DR21 Manual de usuario

Enclume

Enclume PR37 Manual de instrucciones

Enclume

Enclume DR20 Manual de instrucciones

Enclume

Enclume PR38 Manual de instrucciones

Enclume

Enclume LR12B Manual de usuario

Enclume

Enclume RACK IT UP Manual de usuario

Enclume

Enclume S RACK PR17 Manual de usuario

Enclume

Enclume QR1 Manual de instrucciones

Enclume

Enclume PR12 Manual de instrucciones

Enclume

Enclume Classic Decor DR1 KD Series Manual de usuario

Enclume

Enclume DUTCH CROWN RACK PR2 Manual de instrucciones

Enclume

Enclume DR1 KD Manual de instrucciones

Enclume

Enclume PR15 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario