Emulex LP9002S Manual de instalación y funcionamiento

LP9002S Installation and Reference Manual

Table of Contents

Installation

Compatability

Prerequisites

Install HBA

Attach Media

Apply Power

View LEDs

Reference

Specifications

FCC and Regulatory Notices

Declaration of

Conformity

Laser Safety

Emulex Drivers, Software and Manuals

Chapter 1 − Installation

Table of Contents

Compatability

Prerequisites

Install HBA

Attach Media

Apply Power

View LEDs

Emulex Drivers, Software and Manuals

Installation

Caution Emulex LightPulse ® Host Bus Adapters (HBAs) contain

electronic components that can be damaged by static

electricity through an electrostatic discharge (ESD) event. To

prevent ESD damage, maintain constant contact with any

grounded metal surface. A grounding wrist strap is useful for

this purpose. Handle the card carefully at all times and

preferably by the edges. Avoid touching electronic

components and keep the card in the original packaging until

you are ready for installation.

Compatibility

Software

Environments Solaris (Sparc)

Hardware

Environments Sun Enterprise (Ultra) servers ES3500, ES4500, ES5500,

ES6500 and UE10K

Prerequisites

Host computer must provide 5VDC and 12VDC bus power• One open 32 or 64−bit data SBus slot with a 5.0 VDC signaling interface• Maximum SBus clock rate of 25 MHz• Media and connectors•

Note The LP9002S supports both a 32− and 64−bit bus, but not in

all transfer modes. For 32−bit slave mode, both 4 byte or less

and burst mode transfers are supported. For 32−bit DMA

mode, only 4 byte or less transfers are supported. For 64−bit,

all transfer modes are supported. The SBus is limited to

64−byte (max.) bursts for 32−bit bus and 128−byte (max.)

bursts for 64−bit bus, in a single bus tenure. Hence,

maximum burst rate is the same as sustained, assuming no

intervening bus tenures from alternate SBus masters.

Emulex Drivers, Software and Manuals

Install the Host Bus Adapter Board

This is a sample installation. Your installation may vary depending on your

system. Please refer to your system documentation for specific installation

instructions.

Record IEEE and serial numbers.

Each host bus adapter port is shipped with a

unique address identifier called the IEEE

address. Since this adapter has two ports, there

are two IEEE addresses. The IEEE address is

used when configuring your system. The serial

number is used when communicating with

Emulex. All numbers are clearly marked on the

board. We recommend that you record these numbers before installing

the adapter.

Turn off and unplug the computer.

Expose an SBus slot.

Remove or add the face plate extension as needed to fit in your SBus

slot.

Insert the board into the SBus slot, aligning the faceplate and the

connector as shown.

Apply pressure to the board as shown to seat the connectors.

Note Some SBus slots have posts next to the

connector which are used to align and

sometimes lock−in a board. If this is the case,

remove the host adapter handle by pulling its

legs toward the edge of the adapter and pulling

up.

Reassemble the computer.7.

Emulex Drivers, Software and Manuals

Attach Media

Note The host bus adapter will not allow normal data transmission

on an optical link unless it is connected to another similar or

compatible laser product (that is, multimode to multimode.)

Use multimode fiber optic cable used with short−wave lasers, that adhere to the

following specifications:

Fiber Optic Cable Maximum Length Minimum

Length Connector

62.5/125 µm

(multimode) 300 meters at 1.0625

Gb/s

150 meters at 2.125

Gb/s

2 meters LC

50/125 µm

(multimode) 500 meters at 1.0625

Gb/s

300 meters at 2.125

Gb/s

2 meters LC

Connect the fiber optic cable to the LC connector on the HBA.1. Connect the other end of the cable to the Fibre Channel device.2.

After the media is connected to the host bus adapter, you are ready to apply

power to the computer.

Emulex Drivers, Software and Manuals

Apply Power

Verify that the host bus adapter is securely installed in the computer.1. Verify that the correct media is attached.2. Plug in and turn on the computer.3. Observe LEDs for Power On Self Test (POST) results.4.

View LEDs

Green and yellow display lights (LEDs) can be seen through openings in the host

bus adapter's mounting bracket. Green indicates power and yellow signifies port

activity.

POST conditions and results are summarized in this table.

Green

LED Yellow

LED State

OFF OFF Wake−up failure (dead board)

OFF ON POST failure (dead board)

OFF Slow blink (1 Hz) Wake−up failure (dead board)

OFF Fast blink (4 Hz) Failure in POST (dead board)

OFF Flashing (irregular) POST processing in progress

ON OFF Failure while functioning

ON ON Failure while functioning

ON Slow blink (1 Hz) Normal − 1 Gb link rate

ON Fast blink (4 Hz) Normal − 2 Gb link rate

Blink (1 Hz) OFF Normal − link down or not yet started

Emulex Drivers, Software and Manuals

Chapter 2 − Reference

Table of Contents

Specifications

FCC and Regulatory Notices

Declaration of Conformity

Laser Safety

Emulex Drivers, Software and Manuals

Reference

Specifications

Parameter Range

Media Interface Dual LC connector

Physical Dimensions Single width SBus form factor 5.78" x 3.3"

Power Requirements 8.1 watts, typical (11.6 max) @ + 5 VDC, + /− 5 %

84 mWatts, typical (120mWatts max) @ +12 VDC,

+/− 0.75 DC

Airflow 100 lf/min (minimum)

Temperature Operating:K2° to 113° F (0° to 45° C)

Storage:−40° to 158° F (−40° to 70° C)

Humidity 5% to 95% non−condensing

Agency Approvals for

LP9002S Class 1 Laser Product per DHHS 21CFR (J) & EN60825

UL recognized to UL1950

CUR recognized to CSA22.2, No.950

TUV certified to EN60950

FCC Rules, Part 15, Class A

Industry Canada, ICES−003, Class A

EMC Directive 89/336/EEC (CE Mark)

EN55022, Class A

EN55024

Australian EMC Framework (C−Tick Mark)

AS/NZS 3548: Class A

VCCI, Class A

Emulex Drivers, Software and Manuals

FCC and Regulatory Notices

CLASS 1 LASER PRODUCT

LASER KLASSE 1

LUOKAN 1 LASERLAITE

APPAREIL A` LASER DE CLASSE 1

The above statement applies to products marketed in the European Union.

Model LP9002 / LP9002L / LP952L / LP9002S / LP9002DC / LP9002C /

LP9402DC (2x5 SFF Models)

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his own expense. Shielded cables must be used between this

equipment and attached peripheral devices. The reader is cautioned that changes

or modifications made to the equipment not expressly approved by Emulex could

void the user's authority to operate this equipment. The above statement applies

to products marketed in the USA

This class A digital apparatus meets all requirements of the Industry Canada (IC)

Interference − Causing Equipment Standard (ICES−003). Cet appareil numerique

de la Classe A respecte toutes les exigences du reglement sur le materiel

brouilleur du Canada. This statement applies to products marketed in Canada.

Emulex Drivers, Software and Manuals

FCC Compliance Information Statement; Models LP9000−N1/L1/T1 (GBIC

Models):

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Responsible Party: Paul Folino, President & CEO, Emulex Corporation, 3535

Harbor Blvd., Costa Mesa, CA 92626, USA, (714) 662−5600

Note: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.•

The reader is cautioned that any changes or modifications to the equipment not

expressly approved by Emulex could void the user’s authority to operate this

equipment.

This class B digital apparatus meets all requirements of the Canadian

Interference − Causing Equipment Regulations. Cet Appareil numerique de la

classe B respecte toutes les exigences du reglement sur le material brouilleur du

Canada.

The above statement applies to products marketed in Canada.

Emulex Drivers, Software and Manuals

Tabla de contenidos

Otros manuales de Adaptador de Emulex

Emulex

Emulex LP10000 Manual de usuario

Emulex

Emulex LPe1150 HBA Manual de usuario

Emulex

Emulex NC551i Manual de usuario

Emulex

Emulex LP10000DC Manual de instalación y funcionamiento

Emulex

Emulex LP9402DC Manual de instalación y funcionamiento

Emulex

Emulex LP1005DC-CM2 Manual de usuario

Emulex

Emulex OneConnect OCe14000-Series Manual de usuario

Emulex

Emulex LP1050Ex Manual de instalación y funcionamiento

Emulex

Emulex LP11000 Manual de usuario

Emulex

Emulex AW520A Manual de usuario

Emulex

Emulex LPe11002 HBA Manual de usuario

Emulex

Emulex LP21000 Manual de usuario

Emulex

Emulex OneConnect OCe14000-Series Manual de usuario

Emulex

Emulex LP10000 Manual de funcionamiento

Emulex

Emulex LP10000 Manual de uso y cuidado

Emulex

Emulex LP982 Manual de instalación y funcionamiento

Emulex

Emulex LP1050DC Manual de instalación y funcionamiento

Emulex

Emulex LPe11004 HBA Instrucciones de montaje

Emulex

Emulex OneConnect OCe14000-Series Manual de usuario

Emulex

Emulex LP9002C Manual de instalación y funcionamiento

Emulex

Emulex OneConnect OCm11102-N-X Manual del propietario

Emulex

Emulex LP10000ExDC Manual de instalación y funcionamiento

Emulex

Emulex LPe15004-Series Manual de usuario

Emulex

Emulex LPE11000 HBA Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario