Emulex LP1050 Manual de instalación y funcionamiento
LP1050 Installation and Reference Manual
Table of Contents
Installation
Features
Compatibility
Prerequisites
Install HBA
Attach Media
Apply Power
View LEDs
Reference
Specifications
FCC Statement
Declaration of Conformity
Laser Safety
Emulex Documentation, Drivers and Software
1
Installation
Features
The LP1050 host bus adapter offers a highly integrated 2Gb/s Fibre Channel HBA for
use in servers based on either the conventional PCI or PCI-X 1.0a expansion bus
architectures. The LP1050 delivers exceptional performance through the use of a sixth
generation Emulex Thor controller. The Thor high-performance controller is a highly
integrated device that combines industry standard embedded ARM9 processors,
1Gig/2Gig SERDES and protocol technology into a single module. The LP1050 is a
single-channel HBA in a low-profile PCI (MD2) compliant card format.
Major Features
●Full duplex 2Gb/s Fibre Channel delivering up to 400MB/s
●Superior transaction processing performance
●Automatic speed negotiation
●Automatic topology detection
●Full fabric support using F_Port and FL_port connections
●Onboard hardware context cache for superior fabric performance
●Support for use of multiple concurrent protocols (SCSI and IP)
●Full support for both FC service class 2 and 3
●Full fabric support in x86 and Itanium environments
●Support for FC-Tape (FCP-2) devices
●66/100/133 MHz PCI-X 1.0a and PCI 2.3 compatibility
●End-to-end parity protection for high data integrity
●Robust suite of software supporting Windows Server 2003, Windows 2000,
Windows NT, Linux and NetWare
●3.3V signaling, 5V tolerant
●Optical small form factor (LC) interface
Compatibility
Software Environments Windows Server 2003, Windows 2000, Windows NT,
Novell Netware and Linux
Hardware Environments PCI hardware platforms: Itanium Processor Family
(for IA-64) and x86 (for IA-32) platforms
Emulex Documentation, Drivers and Software
2
Prerequisites
●PCI/PCI-X 32- and 64-bit data and addressing
●PCI bus computer with a clock rate up to 66 MHz
●PCI-X bus computer with a clock rate up to 133 MHz
●Media and connectors
Emulex Documentation, Drivers and Software
3
Install the Host Bus Adapter Board
Caution Emulex LightPulse®Host Bus Adapters (HBAs) contain
electronic components that can be damaged by static
electricity through an electrostatic discharge (ESD) event.
To prevent ESD damage, maintain constant contact with
any grounded metal surface. A grounding wrist strap is
useful for this purpose. Handle the card carefully at all
times and preferably by the edges. Avoid touching
electronic components and keep the card in the original
packaging until you are ready for installation.
1. Record IEEE and serial numbers.
Each host bus adapter (HBA) is shipped with a unique 64-bit identifier called
the IEEE address. The Fibre Channel industry uses a World Wide Name
(WWN) derived from the IEEE address, and this number is needed for Fibre
Channel connectivity. The IEEE address is used when configuring your system.
The serial number is used when communicating with Emulex. All numbers are
clearly marked on the board. We recommend that you record these numbers
before installation.
2. Turn off and unplug the computer.
3. Remove the computer case.
Note For best I/O performance, place the adapter into
an empty PCI-X slot that is running at 133 MHz.
Ensure that the PCI bus is not shared with another
PCI card that can lower the PCI slot clock rate.
4. Remove the blank panel from an empty 32- or 64-bit PCI or PCI-X bus slot.
Compare the removed panel to the bracket on the host bus adapter. Follow
steps 5-8 to change the bracket if they are different sizes. Otherwise, skip to
step 9.
Emulex Documentation, Drivers and Software
4
Note The host bus adapter comes with a standard PCI
bracket installed. The low-profile mounting bracket
is shorter than the standard bracket;
approximately 3.11 in. (7.9 cm) compared to 4.75
in. (12.06 cm) long.
If you need a low-profile bracket, contact Emulex
Product Information by phone at 800-EMULEX-3
(800-368-5393) or 714-885-3450, or by e-mail at
shipped within one business day.
5. Remove the mounting bracket screws from the top of the
host bus adapter.
6. Remove the bracket and store it for future use.
7. Align the new mounting bracket tabs with the holes in the
HBA.
Note Be careful not to push the bracket past
the transceiver housing's grounding tabs.
Make sure the LEDs are properly aligned
with the holes in the bracket.
8. Replace the screws that attach the HBA to the bracket.
9. Insert the host bus adapter into the empty 32- or 64-bit PCI
or PCI-X bus slot. Press firmly until it is seated.
10. Secure the host bus adapter's mounting bracket to the case with the panel
screw or clip.
11. Replace the computer case and tighten case screws.
The host bus adapter is now installed in the PC and is ready for media attachment.
Emulex Documentation, Drivers and Software
5
Attach Media
Note The host bus adapter (HBA) will not allow normal data
transmission on an optical link unless it is connected to
another similar or compatible laser product (that is,
multimode to multimode.)
Use multimode fiber optic cable, with short-wave lasers, that adheres to the following
specifications:
Fiber Optic Cable Maximum Length Minimum
Length Connector
62.5/125 µm (multimode) 300 meters at 1.0625 Gb/s
150 meters at 2.125 Gb/s 2 meters LC
50/125 µm (multimode) 500 meters at 1.0625 Gb/s
300 meters at 2.125 Gb/s 2 meters LC
1. Connect the fiber optic cable to the LC
connector on the HBA.
2. Connect the other end of the cable to
the Fibre Channel device.
After the media is connected to the host bus
adapter, you are ready to apply power to the
computer.
Emulex Documentation, Drivers and Software
6
Apply Power
1. Verify that the host bus adapter is securely installed in the computer.
2. Verify that the correct media is attached.
3. Plug in and turn on the computer.
4. Observe LEDs for Power On Self Test (POST) results.
View LEDs
Green and yellow LEDs can be seen through openings in the host bus
adapter's mounting bracket. Green indicates power and yellow signifies
port activity. Each port has a corresponding set of green and yellow LEDs.
POST conditions and results are summarized in the following table.
Yellow
LED Green
LED State
OFF OFF Wake-up failure (dead board). Check the
3.3V LED near the top edge of the HBA
(component side).* If this LED is lit, the slot is
providing 3.3V power.
ON OFF POST failure (dead board)
Slow blink
(1 Hz) OFF Wake-up failure (dead board)
Fast blink
(4 Hz) OFF Failure in POST (dead board)
Flashing
(irregular) OFF POST processing in progress
OFF ON Failure while functioning
Emulex Documentation, Drivers and Software
7
ON ON Failure while functioning
Slow blink ON Normal operating condition - 1 GHz link rate
Fast blink ON Normal operating condition - 2 GHz link rate
OFF Slow blink Normal - link down or not yet started
Slow blink Slow blink Offline for download
Fast blink Slow blink Restricted offline mode (waiting for restart)
Flashing Slow blink Restricted offline mode, test active
*A light-emitting diode (LED) is located near the top edge of the board.
This LED indicates 3.3V power.
Emulex Documentation, Drivers and Software
8
Reference
Specifications
Parameter Range
Media Interface The Thor controller interfaces to the physical media through
an FC-0 Media Interface (FC-PI compliant transceiver), and
then connects through a single optical fiber LC connector.
Physical Dimensions Low-profile MD2 form factor, 6.600 inches by 2.536 inches,
and accommodates both the full-height and low-profile
bracket.
Power Requirements
In a PCI/PCI-X, 66-MHz host:
●3.2 watts (typical) @ +3.3 VDC
●4.8 watts (typical) @ +5.0 VDC
●8.0 watts (total typical)
In a PCI-X, 100/133-MHz host:
●3.7 watts (typical) @ +3.3 VDC
●5.2 watts (typical) @ +5.0 VDC
●8.9 watts (total typical)
Airflow 100 lf/min (minimum)
Temperature 32° to 113° F (0° to 45° C), Operating
-40° to 158° F (-40° to 70° C), Storage
Humidity 5% to 95% non-condensing
Agency Approvals for
LP1050
Class 1 Laser Product per DHHS 21CFR (J) & EN60825-1
UL recognized to UL1950
CUR recognized to CSA 22.2, No. 950
Baurt-certified by TUV to EN60950
FCC Rules, Part 15, Class A
Industry Canada, ICES-003, Class A
EMC Directive 89/336/EEC (CE Mark)
EN55022, Class A
EN55024
Australian EMC Framework (C-Tick Mark)
AS/NZS 3548:1995 Class A
Japan VCCI, Class A
Taiwan BSMI, Class A
Korea MIC, Class A
Emulex Documentation, Drivers and Software
9
FCC and Regulatory Notices
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A` LASER DE CLASSE 1
LP10000DC-M2, LP10000-M2, LP1050DC-F2 and LP1050-F2 Models
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Responsible Party: Paul Folino, Chief Executive Officer
Emulex Corporation (714) 662-5600
3535 Harbor Blvd. Costa Mesa, CA Corporation 92626 USA
Note:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense. Shielded cables must be used between this equipment and attached
peripheral devices. The reader is cautioned that changes or modifications made to the
equipment not expressly approved by Emulex could void the user's authority to operate this
equipment. The above statement applies to products marketed in the USA
This class A digital apparatus meets all requirements of the Industry Canada (IC) Interference -
Causing Equipment Standard (ICES-003).
Cet appareil numerique de la Classe A respecte toutes les exigences du reglement sur le
materiel brouilleur du Canada. This statement applies to products marketed in Canada.
Emulex Documentation, Drivers and Software
10
Tabla de contenidos
Otros manuales de Adaptador de Emulex
Emulex
Emulex LP10000 Manual de uso y cuidado
Emulex
Emulex LP9002C Manual de instalación y funcionamiento
Emulex
Emulex OneConnect OCe14000-Series Manual de usuario
Emulex
Emulex OneConnect OCe14000-Series Manual de usuario
Emulex
Emulex LP10000ExDC Manual de instalación y funcionamiento
Emulex
Emulex LP10000 Manual de usuario
Emulex
Emulex OneConnect OCm11102-N-X Manual del propietario
Emulex
Emulex LPe15004-Series Manual de usuario
Emulex
Emulex LP952L Manual de instalación y funcionamiento
Emulex
Emulex LPE11000 HBA Manual de usuario
Emulex
Emulex LP9002S Manual de instalación y funcionamiento
Emulex
Emulex LPe11004 HBA Instrucciones de montaje
Emulex
Emulex LP9402DC Manual de instalación y funcionamiento
Emulex
Emulex AW520A Manual de usuario
Emulex
Emulex NC551i Manual de usuario
Emulex
Emulex LPe1150 HBA Manual de usuario
Emulex
Emulex LP10000 Manual de funcionamiento
Emulex
Emulex LP10000 Manual de instalación y funcionamiento
Emulex
Emulex LP10000DC Manual de instalación y funcionamiento
Emulex
Emulex LP21000 Manual de usuario
