EMS FireCellWDC Manual de usuario

Installation

Guide

Contents

Ordering information

Pre installation

Components

Equipment familiarisation

Insert batteries

Add to system - unprogrammed systems only

Assign device

Position template against door

Drill xing positions

Fix unit to door

Position oor plate

Mark oor plate xing positions

Drill oor plate xing positions

Fix oor plate to oor

Open re door & depress plunger

Post installation conguration

Test device

Troubleshooting

Device tone & ash indication

Specication

Regulatory information

8. Mark xing positions

10. Fix oorplate to oor

=6mm

9. Drill xing Positions

CHECK FOR

WATER

PIPES

ELECTRIC

CABLES

GAS

PIPES

1. Introduction

The following steps

are a quick reference

overviewonly.

Refer to the FireCell WDC

Installation Guide (MK241) for

fullinstallation details.

RESET LOGON

BACK

HEALTHY

FAULT

SYSFAULT

LOOP1

INOUTIN OUT

LOOP2

INOUTIN OUT

LOOP3

INOUTIN OUT

LOOP4

INOUTIN OUT

RF1 RF2

AddNew Device

3. Add to system

2. Insert batteries

OBSERVE

POLARITY!

Ensure ESD

protection label is

fitted when

installing WDC on

metal kick plates

or uneven surfaces

(inside cut out)

4. Positiontemplate

FITESD PROTECTION LABEL

IFFITTING TO A METALLIC SURFACE

5. Drill xing positions

=2.5mm

6. Fix unit to door

7. Position oor plate

11. Open door

12.Test device

Ordering information

Pre installation

Part no Product description

FC-60-2000 FireCell Wireless Door Control (Black)

FC-60-2010 FireCell Wireless Door Control (White)

Installation must conform to applicable local installation codes and

should only be installed by a fully trained competent person.

Ensure that the device is installed as per the site survey.

Ensure that the device is tted to the side of the door that shuts against the

door frame.

The supplied ESD protection label must be tted when installing the

Wireless Door Control (WDC) on metal kick plates or uneven surfaces.

DO NOT press the log on button on a pre-programmed device, as this will

cause communication with the control panel to be lost. Should this happen,

delete the device from the system and add it back on.

Before installing the device, ensure that the re door is suitable e.g. self

closing, has a at surface to x to and has appropriate clearance under the

door to accommodate the oor plate.

Any door closing devices used in conjunction with the WDC must conform to

EN 1154.

Components

FireCell

WDC

Small & large

oor plates

1 2 Fixing template

(MK255)

Fixings

ESD protection

label

Equipment familiarisation

Ferrule

Plunger

Battery

compartment

Log on button

Fixing position

Insert batteries

When tting / replacing batteries;

observe correct polarity, using only

specied batteries.

Indication LED

Note; upon rst power

up the device will

initiate a startup sequence,

denoted by a series of low

pitched beeps and motor

operations. This sequence will

take approximately 15 seconds

and concludes with three low

pitched beeps.

Should the sequence close with a

mix of high and low pitched

beeps, refer to page 13.

Free to download from

www.emsgroup.co.uk

Add to system - unprogrammed systems only

The device’s loop address is congured within the menu structure of the radio

hub. It is recommended to congure the device to the system prior to

installation.

Note; devices can alternatively be added to the system after installation. If this

method is to be taken, it is recommended to note the devices ident number at

this stage. Skip this section and refer to the ‘Post Installation Conguration’

section on page 10 for details on the device’s ident location.

Note; if programming the FireCell WDC to a Fusion Loop Module, refer to the

Fusion Loop Module Engineers Guide (TSD062) for programming details.

Skip this step If the device has been supplied as part of a

pre-programmed system, as this will cause communication with the

control panel to be lost. Should this happen, delete the device from

the system and add it back on.

To add devices by log on (pre installation);

From Front Display Add New Device Select Desired RCC 01 Set Loop 1

.Addr 003 Add By Log On Press Dev Log On ‘press the devices

log on button, followed by Add Dev 03456 Y? New Addr L1 A003.

To Exit

The device has now been added to the Radio Hub and should be installed in its

location. For further details, refer to the

programming manual (MK98) for full

programming information.

BACK

Note: the device can also be programmed utilising the control panel’s cause and

eects, as part of the buildings evacuation plan.

Assign device

RESET LOGON

BACK

HEALTHY

FA U LT

SYS FAULT

LOOP 1

IN OUT IN OUT

LOOP 2

IN OUT IN OUT

LOOP 3

IN OUT IN OUT

LOOP 4

IN OUT IN OUT

RF1 RF2

Assign Device

Newly added devices must now be assigned to the system.

From Unassigned Dev Assign Device Assign All Dev 000 of 001

changing to Done 001 of 001 (once complete)

To Exit

BACK

Position template against door

If the device is to be tted to a metal surface, e.g. a

metal kick plate, the ESD protection label must be

tted. Simply ax the label inside the xing template’s cut

out, on to the metal surface.

Note: the device must now also be added and

congured on the control panel. Refer to the FireCell

Programming Guide (MK98) for details.

Use all four xing positions.

Use supplied xing screws.

Fix unit to door

= 2.5mm

Drill xing positions

Drill all four xing positions.

Mark oor plate xing positions

Use small oor plate, if bumpstop

creates a trip hazard

Mark all four xing positions.

Position oor plate

Door

Bump

stop

Side view

Ferrule

Floor plate

Fix oor plate to oor

Use all four xing holes.

Use supplied xing screws.

Drill oor plate xing positions

Before drilling, check

locations of water pipes,

gas pipes & electrical cables

= 6 mm

Open re door & depress plunger

Open door against bump

stop and depress plunger -

check ferrule ts neatly into

recess

Post installation conguration

Skip this step if the device has already been congured to the

system

To add devices by ident (post installation);

From Front Display Add New Device Select Desired RCC 01 Set Loop 1

.Addr 003 Add By Ident Add Dev 01ABC Y? ’Enter the Device’s ident

.’Enter the device type Input Output Device New Addr L1 A003 .

To Exit

BACK

The device must now be assigned to the system. Refer to the ‘ Assign Devices’

section on page 6 for details.

Ensure the device’s ident number has

been noted. The device’s ident is located

at the top of the device as shown:

01ABC

Device top view

Tabla de contenidos

Otros manuales de Unidad de control de EMS

EMS

EMS fusion FCX-532-001 Manual de usuario

EMS

EMS ZITON Manual del propietario

EMS

EMS LRP2000 Series Manual de usuario

EMS

EMS FireCell FCZ-170-111 Manual de usuario

EMS

EMS Fusion FCX-532-001 Manual de usuario

EMS

EMS FireCell FCZ-170-111 Manual de usuario

EMS

EMS EMS520 Manual de usuario

EMS

EMS ZITON RADIO LOOP MODULE Manual del propietario

EMS

EMS EC-41-0200 Manual de usuario

EMS

EMS EC-41-0200 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario