TB-6525 Page 4 of 4
EMIT - 3651 Walnut Avenue, Chino, CA 91710 • (909) 664-9980 • Fax (909) 627-7449 • Website: DescoEMIT.com
Limited Warranty
EMIT expressly warrants that for a period of five (5) years from the
date of purchase, EMIT Bench Top Ionizers will be free of defects in
material (parts) and workmanship (labor). Within the warranty period, a
credit for purchase of replacement EMIT products, or, at EMIT’s option,
the product will be repaired or replaced free of charge. If product credit
is issued, the amount will be calculated by multiplying the unused
portion of the expected five year life times the original unit purchase
price. Call our Customer Service Department at 909-664-9980
(Chino, CA) or 01892 665313 (Crowborough, U.K.) for a Return
Material Authorization (RMA) and proper shipping instructions and
address. Please include a copy of your original packing slip, invoice,
or other proof of date of purchase. Any unit under warranty should be
shipped prepaid to the EMIT factory. Warranty replacements will take
approximately two weeks.
If your unit is out of warranty, call our Customer Service Department at
909-664-9980 (Chino, CA) or 01892 665313 (Crowborough, U.K.) for a
Return Material Authorization (RMA) and proper shipping instructions
and address. Desco EMIT will quote repair charges necessary to bring
your unit up to factory standards.
Warranty Exclusions
THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU
OF ALL OTHER PRODUCT WARRANTIES, EXPRESSED AND
IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE WHICH ARE SPECIFICALLY DISCLAIMED.
The express warranty will not apply to defects or damage due to
accidents, neglect, misuse, alterations, operator error, or failure to
properly maintain, clean or repair products.
Limit of Liability
Electronic ionizers use high voltage corona discharge and should not
be used in or near flammable or explosive environments. In no event
will EMIT or any seller be responsible or liable for any injury, loss or
damage, direct or consequential, arising out of the use of or the inability
to use the product. Before using, users shall determine the suitability
of the product for their intended use, and users assume all risk and
liability whatsoever in connection therewith.
Adjustment
There are no user adjustable or serviceable parts inside the
ionizer. Adjusting or dismantling your ionizer may create
dangerous conditions and unauthorized modifications will
void the product warranty. Servicing should be performed
only at the factory, or by a technician trained in high voltage
circuits. See warranty section for repair information.
Health
There are no known health risks associated with our
devices. The emitters work at about 4-6 kV and can create
ozone, but there have been no significant measurement
of ozone from our emitter sets, as all our existing units
test well below the OSHA limit of 0.05 ppm ozone. For
additional safety information, see “Dispelling an Old Myth”
written by William Metz of Hewlett-Packard published in
Evaluation Engineering magazine, September 2001.
Specifications
Input: 120 VAC - 50/60 Hz - 3.0 Amps
Fuse Type: Slow blow 5 amp
Output: 4.5 KV at 50 - 60 nano amps
Airflow: Adjustable 117 CFM maximum
Balance Voltage*: ±5v
Size: 11” x 9” x 7”
Weight: 12 Pounds
Cord: Cord with three wire IEC plug
(ground required)
*EMIT ionizers meet the ANSI/ESD S20.20 minimum
recommended technical requirement range of less than ±50 volts
voltage offset tested in accordance with ANSI EOS/ESD S3.1.
EMIT model 50600 greatly exceeds the requirement providing ±5
volt auto balancing.
© 2009 DESCO INDUSTRIES INC.
Employee Owned
MFG Specifications Recorded Values
Offset voltage
(floating voltage)
in voltage
+/-10 volts at TP2
(1 foot)
Discharge time,
+1000volts to
+100volts in
seconds
2 sec or less at TP2
(1 foot)
Discharge time,
-1000volts to
-100volts in
seconds
2 sec or less at TP2
(1 foot)
