Emerson SSW Series Manual de usuario

Uninterruptible Power Supply

User Manual

SSW UPS Series

CONTENTS

What's Included. . . . . . . . . . . . . . . . . . . . . . . 1

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . 1

2.0 Important Safety Instructions . . . . . . . . . . . . . . 2

3.0 General Description . . . . . . . . . . . . . . . . . . . 3

4.0 System Block Diagrams . . . . . . . . . . . . . . . . . 5

5.0 Installation and Operation. . . . . . . . . . . . . . . . 6

6.0 LCD Screen Diagnostics . . . . . . . . . . . . . . . . . 7

7.0 Battery Replacement . . . . . . . . . . . . . . . . . 10

8.0 Troubleshooting . . . . . . . . . . . . . . . . . . . 15

9.0 Technical Specifications . . . . . . . . . . . . . . . . 16

Technical Support . . . . . . . . . . . . . . . . . . . . . 18

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 18

Page: 1

What's Included

The UPS is shipped with the following items:

• User manual

• USB cable: High speed 2.0 Standard Type A-B, 6 ft (1.8 m)

NOTE: UPSwatch - Power Monitoring and Control Software is available for download at www.solahd.com.

The software is compatible with: Windows 7, 8, 10, Windows 2008, 2012, 2016, Windows 2008/2012

Server Core, Hyper-V 2008/2012, Linux OpenSUSE 11.4, Linux ubuntu 10.04, Linux Fedora 3.1.9, CentOS 5.8,

Citrix XenServer 6.0.0, Linux KVM.

Accessory (Optional)

• SSWSNMPCARD: SNMP card for SSW1500 models only. This SNMP card provides an advanced,

yet easy-to-use network management function which supports both SNMP and HTTP. Features include:

multiple system shutdown, event notication, scheduling, and control and conguration of the UPS

remotely. The SNMP card must be inserted into the Communication Port on the rear panel of the UPS.

Please visit www.solahd.com for more information.

1.0 Introduction

Thank you for selecting the SSW Uninterruptible Power System. This manual contains important safety

instructions that should be folllowed during the installation and operation of your UPS.

• Please read all safety, installation and operating instructions before attempting to install or operate

the UPS.

• Please adhere to all warnings on the unit and in this manual during installation and operation.

This UPS is designed for industrial or commercial use. The UPS features a compact design that ts into a

limited-space working environment.

This product features the following:

• LCD display

• User-replaceable battery

• High reliability

• Auto restart during AC recovery

• AC overload protection

• Over temperature thermal protection

• Battery overcharge protection

• AVR (Auto Voltage Regulation)

• Input voltage out-of-range protection

• Remote monitoring and control software via UPSwatch

• Site wiring fault indicator

Page: 2

2.0 Important Safety Instructions

!WARNING - Risk of electric shock, fire and personal injury.

SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed

during installation and maintenance of the UPS and batteries.

The UPS is intended for installation in a controlled environment.

• Install the UPS in an indoor temperature- and humidity-controlled environment, free of

conductive contaminants.

• Do not install the UPS in or near water.

• In order to avoid overheating the UPS, allow proper ventilation of the unit. Do not block or cover the top,

bottom or sides of the UPS.

• Do not expose the UPS to direct sunlight or install the unit near any heat sources.

• Install the UPS onto a level surface in an upright position. Do not place the UPS on an unstable surface

such as a cart, stand or table.

• The UPS must be installed near the socket receptacle so that the cord can be easily disconnected.

To properly turn off the UPS, press the ON/OFF button for three (3) seconds, then disconnect the

input power supply cord from the AC power outlet.

• Connect the AC input power cord to a properly grounded AC supply source.

• Connect the UPS to a grounded supply circuit with proper branch circuit protection. Follow all applicable

National Electrical Codes®(NEC®) and Canadian Electrical Codes (CEC) as well as all local codes.

• This UPS is not for use in a computer room as dened in the Standard For the Fire Protection of

Information Technology Equipment, NFPA 75.

• Do not plug the UPS into a power strip. Do not daisy-chain one UPS power cord into another UPS

output receptacle.

• Do not place the UPS power cord where it may be damaged.

• Do not dispose of the UPS in a re as the battery may explode.

• Do not open or damage the battery. Released electrolyte is harmful to the skin and eyes and

may be toxic.

• Turn off the UPS and disconnect the input cord from the AC power supply before cleaning. Do not use

liquid or aerosol cleaners. Use only a dry cloth on the exterior of the UPS. Do not open the unit.

Page: 3

3.0 General Description

3.1 Front Panel

LCD

• The LCD will show functions of the UPS operation status.

ON/OFF Button

• To turn the UPS on, press the ON/OFF button for two (2) seconds and the LCD will display UPS status.

• To turn the UPS off, press the ON/OFF button for two (2) seconds and LCD display will shut off.

Setup Button

When you press the setup button, the LCD screen will display the functions below in the following sequence:

• Input Voltage (V)

• Input Frequency (Hz)

• Output Voltage (V)

• Output Frequency (Hz)

• Output Load (%)

• Output Load (kVA)

• Battery Voltage (%)

• Battery Voltage (V)

Page: 4

3.2 Rear Views

USB

Port

RJ 45

Surge

Input

Cable

Breaker

Site Fault

Indicator

Receptacles

Protection

Rear View of SSW700 and SSW1000

USB

Port

RJ 45

Surge

Input

Cable

Breaker

Site Fault

Indicator

Receptacles

Optional

SNMP

Protection

Rear View of SSW1500

Page: 5

4.0 System Block Diagrams

SSW700 and 1000 System Block Diagram

SSW1500 System Block Diagram

Page: 6

5.0 Installation and Operation

5.1 Installation Requirements

• Install the UPS in a controlled environment with adequate ventilation that is free of excessive dust

and high humidity.

• Avoid direct sunlight.

• Maintain a clearance of 4 inches (100 mm) between the UPS rear panel and the wall and 1 inch (25.4 mm)

between the UPS sides and the wall. Keep the air inlets unobstructed to facilitate ventilation and

heat dissipation.

5.2 Connect to Utility Power

Connect the power cord to the AC input power outlet.

5.3 Check the Site Wiring Fault Indicator

Check the site wiring fault indicator on the rear panel of the UPS. The light will be illuminated if the UPS

is plugged into an improperly wired AC power outlet. Detected wiring faults include ground and hot-neutral

polarity reversal.

5.4 Charge the Battery

The UPS charges its battery whenever it is connected to utility power, even when the unit is off. For best

results, charge the battery for eight (8) hours before initial use.

5.5 Turn On the UPS

Press the ON/OFF button for 2 seconds.

5.6 Set Up Audible Alarm On/Off

When the UPS powers on, the audible alarm may sound. The steps below outline how to turn the audible

alarm on or off.

• Step1: Press and hold the ON/OFF button for three (3) seconds to set up audible alarm ON/OFF

• Step2: Press the setup button once to set up audible alarm ON/OFF

• Step3: Press the ON/OFF button to exit

5.7 Connect the Loads

Connect the loads to the output receptacles on the rear panel of the UPS.

5.8 Connect Computer Interface

UPS monitoring software and an optional interface kit can be used with this UPS. If used, connect the interface

cable to the REMOTE PORT on the rear panel of the UPS and to the host computer (either COM 1 or COM 2).

5.9 Install the Optional SNMP Card (SSW1500 Models Only)

• Remove the Communication Port cover. Insert the SNMP card and secure with screws.

• Use network cables (supplied by user) to connect the UPS to the computer

network port.

• Please refer to the SNMP card operation website at www.SolaHD.com

for conguration settings and further instructions.

Page: 7

6.0 LCD Screen Diagnostics

Operation and Overview of LCD Panel

UPS Power On

To turn on the UPS unit, press the ON/OFF button

lightly for 2 seconds then the LCD will display on.

UPS Power Off

To turn off the UPS unit, press the ON/OFF button

lightly for 2 seconds then the LCD will display off.

AC Start Mode

AC start mode, the back light will ash once every

0.5 second.

Line and AVR Mode

AVR mode, the bottom icon will ash once every

0.5 second.

Page: 6

4.0 Interface

Operation and Overview of LCD Panel

Operation Mode

Status

Load and Battery capacity

Number will be displayed in the

following order Vin, Vo, load, battery

capacity

UPS Power On

To turn on the UPS unit, press the power switch SW2

lightly for 2 seconds then the LCD will display on.

UPS Power Off

To turn off the UPS unit, press the power switch SW2

lightly for 3 seconds then the LCD will display off.

AC Start Mode

ACstartmode,thebacklightwillashonceevery

0.5second

Line and AVR Mode

AVRmode,thebottomiconwillflashonce

every0.5second.

Battery Mode Low Battery

Batteryvoltagelow,thebatteryalarmiconwillash

onceevery0.5second.

SSW UPS

Rev.3 2019/05/30

Page: 8

Battery Mode Low Battery

Battery voltage low, the battery alarm icon will

ash once every 0.5 second.

Battery Sleep Mode

Battery voltage UVP, the battery stops to provide

power, and the battery alarm icon will ash once

every 0.5 second.

Battery Voltage Over Charge

Battery voltage over charge, the battery alarm icon

will ash once every 0.5 second and display HI.

Short for Line and AVR Mode

LCD display SP, when UPS operates in LINE or

AVR mode.

Short for Battery Mode

LCD display SP, when UPS operates in

battery mode.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unión Postal Universal de Emerson

Emerson

Emerson SolaHD S4K2UC Series Manual de usuario

Emerson

Emerson Liebert GXT4-5000RT208 Manual de usuario

Emerson

Emerson Adapt Manual de usuario

Emerson

Emerson Liebert GXT4-5000RT230 Manual de usuario

Emerson

Emerson Liebert GXT4-6000RT230 Manual de usuario

Emerson

Emerson NXr Manual de usuario

Emerson

Emerson ECP-024 Manual de usuario

Emerson

Emerson Liebert GXT3-5000RT230 Manual de usuario

Emerson

Emerson Liebert NXC 10-20kVA Manual de instrucciones

Emerson

Emerson Liebert PSA 1000VA Manual de usuario

Emerson

Emerson Liebert ITA 5kVA Manual de usuario

Emerson

Emerson Liebert GXT MT+LB 10KL Manual de usuario

Emerson

Emerson Liebert NX 400V Manual de usuario

Emerson

Emerson Liebert GXT3 Series Manual de usuario

Emerson

Emerson Series 610 Manual de usuario

Emerson

Emerson Liebert itON 1500VA Manual de usuario

Emerson

Emerson Liebert Nfinity 12-20kVA Manual de usuario

Emerson

Emerson Liebert GXT3 Series Manual de usuario

Emerson

Emerson Liebert NX300 Series Manual de usuario

Emerson

Emerson Liebert FPC Manual de usuario

Emerson

Emerson Liebert itON BX Manual de usuario

Emerson

Emerson Liebert ITA Manual de usuario

Emerson

Emerson Liebert PSP500MT3-230U Manual de usuario

Emerson

Emerson Liebert GXT Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario

ZincFive

ZincFive BC Series Manual de usuario