Emerson EE542-1Z Manual de usuario
EE542-1Z
I
Installation Manual
Smart EnergyProgrammable Thermostat + Energy Monitor
1
2
3
3
4
6
9
14
17
19
20 - 22
Back Cover
Contents
Introduction
Getting Started
Installing the Thermostat
Quick Guide
Step 1: Remove the Old Thermostat
Step 2: Mount the New Thermostat
Step 3: Configure the Thermostat
Step 4: Check Thermostat Operation
Step 5: Pair Device to Home Area Network
Step 6:Verify Wireless Connectivity
Wiring Chart
Wiring Table
Introduction
• About this Guide
• System Compatibility
1
This guide describes how to install and configure your new
Smart Energy thermostat.
This product replaces most thermostats, including those
that work with:
• Standard Heat and Cool Systems
• Two-Stage Heat and Two-Stage Cool Systems
• Air Source Heat Pump (with Aux. or Emergency Heat)
• Ground Source Heat Pump (with Aux. or Emergency Heat)
• Air or Ground Source Heat Pump (No Aux. or Emergency Heat)
• Standard Heat Only Systems
• Standard Central Air Conditioning
• Gas or Oil Heat
• Electric Furnace
• Hydronic (Hot Water) Zone Heat – 2 Wire zone valves
Failure to read and follow all instructions carefully before installing or
operating this control could cause personal injury and/or property
damage.
To prevent electrical shock and/or equipment damage, disconnect
electric power to system at main fuse or circuit breaker box until
installation is complete.
Do not use on circuits exceeding specified voltage. Higher voltage will
damage control and could cause shock or fire hazard.
CAUTION
Getting Started
Note: This product requires a
24v AC power supply via the
C terminal for operation.
• Thermostat (1)
• Wall anchors (2)
• Mounting screws (2)
Required Items
• Flat blade screwdrivers – 1 large and 1 micro tip
• Hand or power drill with 3/16 inch drill bit
• Wire strippers
• Level (optional)
Required Tools
Before you begin to install your Smart Energy thermostat:
Read these instructions thoroughly.
Check the package from your thermostat to make sure you have
all of the required items (see below).
Check to ensure you have the required tools (see below).
Pre-Installation Checklist
2
O/B
G
W/E
W2
L
Y2
Y1
RC
RH
C
3
To prevent electrical shock and/or equipment damage, disconnect
electric power to system at main fuse or circuit breaker box until
installation is complete.
CAUTION
Quick Guide
• Turn off power at the breaker.
• Remove cover from old thermostat to expose wires.
• Document which wires go to which terminals using the table
on the back of this manual.
• Disconnect wires and remove old thermostat, making sure that
thermostat wires do not fall back into wall opening.
STEP 1. Remove the old thermostat
• Feed thermostat wires through thermostat hole.
• Wire new thermostat.
• Turn on power at breaker.
STEP 2. Mount the new thermostat
STEP 3. Configure the thermostat
STEP 4. Check thermostat operation
STEP 5.Verify wireless connectivity
The sections that follow provide detailed instructions
for completing these steps.
4
To prevent electrical shock and/or equipment damage, disconnect electric
power to system at main fuse or circuit breaker box until installation is
complete.
CAUTION
This product does not contain mercury. However this product may replace a
product that contains mercury.
Mercury and products containing mercury must not be discarded in household
trash. Do not touch any spilled mercury. Wearing non-absorbent gloves, clean up
any spilled mercury and place in a sealed container. For proper disposal of a
product containing mercury or a sealed container of spilled mercury, place it in a
suitable shipping container. Refer to www.thermostat-recycle.org for location to
send the product containing mercury.
ATTENTION: MERCURY NOTICE
STEP 1. Remove the Old Thermostat.
1. Cover
2. Base, which you can remove by loosening all screws
3. Wall plate, which you can remove by unscrewing the
mounting screws that hold it on the wall or adaptor plate
Thermostat Components
Most thermostats consist of three basic parts.
Wall plateBase
Cover
3-Part Thermostat
5
Remove the Old Thermostat
Important: Do not let wires fall back into the wall.
1. Remove the front cover of the old thermostat.
2. With wires still attached, remove wall plate from the
wall by loosening the screws. If the old thermostat has a wall
mounting plate, remove both the thermostat and the wall
mounting plate.
3. Identify each wire attached to the old thermostat as shown in the
diagram below. Before removing wires from old thermostat,
label each wire with the letter on the old thermostat or document
the color of wire going into each terminal in the table located on
the back cover of this manual.
4. Disconnect the wires from the old thermostat one at a time.
Wall opening
Wall plate hanging on the wires
You may want to wrap the wires
around a pencil to keep them from
falling back into the wall.
TIP
Wall opening
C
W
O/B
G
W/E
W2
L
Y2
Y1
RC
RH
C
C
6
Take care when securing and routing wires so they do not short to
adjacent terminals or rear of thermostat. Personal injury and/or
property damage may occur.
CAUTION
STEP 2. Mount the New Thermostat
1. Unpack the thermostat and separate the mounting plate from the
thermostat. Remove the packing material from the thermostat.
Gently pull the thermostat straight off of the base. Hold the back
of the thermostat by the lower corners with one hand, and pull
the wall plate off with the other hand.
2.
Feed thermostat wires through rectangular hole between the
terminal blocks in the thermostat wall plate.
Mount the new thermostat
NOTE: Forcing or prying on the thermostat will cause damage to the unit.
Wall plate
Feed wires through
this hole from back
Mounting
holes
O/B
G
W/E
W2
L
Y2
Y1
RC
RH
C
C
7
3.
Once you have established the desired location of the thermostat,
use a pencil, and the wall plate as a template, to mark the
location of the mounting holes on your wall.
4.
Move wall plate out of the way and drill two holes using a
3/16" drill bit.
5.
Feed the thermostat wires through the rectangular hole and
fasten wall plate loosely to wall using two mounting screws in
mounting holes.
If desired, place a level against bottom of the wall plate and
adjust until level before tightening screws (leveling is for
appearance only and does not affect thermostat operation).
If you are using existing mounting holes, or if holes drilled are
too large and do not allow you to tighten base snugly, use
plastic wall anchors included with the product.
6.
Connect wires to the thermostat wall plate. The image below
shows the location of the wire terminals. Each terminal is
labeled with a letter or letter number combination.
Wall plate
Wire
Terminals
Feed wires through
this hole from back Connect
wires here
8
Connect wires as follows:
• If necessary, strip insulation about 3/8 inch from the end
of the wire.
• Use the table you previously filled out on the back of the
installation manual (or the wiring chart on page 20) to locate
the correct terminal for each wire connection.
• Bend the wire slightly, insert the wire under the contact plate,
and use a small flat head screwdriver to secure the wire
into place.
7.
Push excess wire into wall and plug hole with a fire resistant
material (such as fiberglass insulation) to prevent drafts from
affecting thermostat operation.
8 Fasten thermostat to wall plate using the quick connect feature.
Make sure the retention tabs on the wall plate are in line with
the retention slots on the thermostat. Gently press the
thermostat onto the wall plate until you hear a clicking sound.
If the thermostat does not easily click do not press with
excessive force or damage could occur to the product.
9. Turn power back on at the breaker.
Otros manuales para EE542-1Z
1
Tabla de contenidos
Otros manuales de Termostato de Emerson
Emerson
Emerson 1F95EZ-0671 Instrucciones de montaje
Emerson
Emerson White Rodgers 755-50 Manual de usuario
Emerson
Emerson 1F83H-21PR Manual de usuario
Emerson
Emerson 1F80-361 Manual de usuario
Emerson
Emerson 1E78-151 Manual de usuario
Emerson
Emerson 1F95-1291 Manual de usuario
Emerson
Emerson 1F83H-21NP Manual de usuario
Emerson
Emerson 1F83C-11NP Manual de usuario
Emerson
Emerson 7903 Instrucciones de funcionamiento
Emerson
Emerson Dixell XR35CX - 110VAC Manual de usuario
Emerson
Emerson White-Rodgers P210 Manual de usuario
Emerson
Emerson White-Rodgers 1F75H-21NP Manual de usuario
Emerson
Emerson 1F86-0471 Manual de usuario
Emerson
Emerson 1F85U-22PR Manual de usuario
Emerson
Emerson White Rodgers 1E30N-910 Manual de usuario
Emerson
Emerson Sensi Manual de usuario
Emerson
Emerson 1F75P-21PR Manual de usuario
Emerson
Emerson Lumity Wireless Touchscreen RTU Thermostat Manual de usuario
Emerson
Emerson delmarva power Manual de usuario
Emerson
Emerson White-Rodgers 1C20 Manual de usuario
Manuales populares de Termostato de otras marcas
EWELLY
EWELLY EW-181 Manual de usuario
Prolon
Prolon T1100 Instrucciones de instalación
Computherm
Computherm Q20 Manual de usuario
Heatmiser
Heatmiser neoStat Manual de usuario
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario
