Emerson Rosemountl Manual de usuario

Quick Start Guide

00825-0100-4952, Rev DC

August 2017

Rosemount™0085 Pipe Clamp Sensor

Assembly

August 2017

Quick Start Guide

Figure 1. Rosemount 0085 Pipe Clamp Sensor Assembly Exploded View

NOTICE

This guide provides basic guidelines for Rosemount 0085 Pipe Clamp Sensor. It does not provide instructions

for configuration, diagnostics, maintenance, service, troubleshooting, explosion-proof, flameproof, or

intrinsically safe (I.S.) installations. Refer to the Rosemount 0085 Pipe Clamp Sensor Reference Manual for more

instruction. The manual and guide are also available electronically on Emerson.com/Rosemount.

If the Rosemount 0085 Sensor was ordered assembled to a temperature transmitter, see the appropriate Quick

Start Guide for information on configuration and hazardous locations certifications.

A. Transmitter

B. Sensor with spring loaded adapter

C. Nipple union of the extension

D. Nut

E. O-ring

F. Mounting hardware

G. Corrosion protection inlay (optional)

H. Pipe clamp

Contents

Location and orientation . . . . . . . . . . . . . . . . . . 3

Install pipe clamp sensor . . . . . . . . . . . . . . . . . . 6

Installing optional accessories . . . . . . . . . . . . . . 7

Rosemount X-well™Technology considerations . 9

Product Certifications . . . . . . . . . . . . . . . . . . . . . . . 11

Quick Start Guide

August 2017

1.0 Location and orientation

The pipe clamp sensor should be mounted on the outside section of the pipe

where the process medium is in contact of the inside of the pipe wall. Ensure

that the pipe surface is clean of debris. The pipe clamp sensor should be

mounted in a secure position to ensure there is no rotational movement after

installation. To ensure ingress protection, the nut of the Rosemount 0085 Pipe

Clamp sensor can be tightened to compress the O-ring to form a seal. The nut

can be accessed and tightened by removing the sensor and the nipple union of

the extension. Refer to “Location and orientation” on page 3 for the location of

each part.

1.1 Horizontal orientation

Though the Rosemount 0085 Pipe Clamp sensor can be mounted in any

orientation for full pipe flow applications, the best practice is to mount the pipe

clamp sensor on the upper half of the pipe. Refer to Figure 2 for more

information.

Figure 2. Horizontal Orientation

1.2 Vertical orientation

The pipe clamp sensor can be installed in any position around the circumference

of the pipe.

Full pipe flow Partial pipe flow

360°

Recommended

Zone

August 2017

Quick Start Guide

Figure 3. Vertical Orientation

1.3 Special considerations

Under most circumstances, the Rosemount 0085 Pipe Clamp Sensor can be

mounted in a direct mount configuration. Since heat from the process is

transferred from the pipe clamp sensor to the transmitter housing, if the

expected process temperature is near or beyond specification limits, consider

using a remote mount configuration to isolate the transmitter from the process.

Refer to the appropriate transmitter reference manual for temperature effects.

Figure 4 displays a pipe clamp sensor assembly in remote mount configuration.

360°

Quick Start Guide

August 2017

Figure 4. Pipe Clamp Sensor Assembly in Remote Mount Configuration

Wireless transmitters with external antennas allow for multiple antenna

configurations. All wireless transmitter should be appropriately 3 ft. (1 m) from

any large structure or building to allow clear communication to other devices.

Wireless transmitters with external antennas should be positioned vertically,

either straight up or straight down.

Figure 5. Wireless Transmitter Orientation

August 2017

Quick Start Guide

2.0 Install pipe clamp sensor

Select the area for pipe clamp sensor installation with the recommendations

outlined in “Horizontal orientation” on page 3. Mount the pipe clamp sensor on

the pipe and snug tighten the bolts. Ensure the sensor passes through the hole

of the pipe clamp and has direct contact between the sensor tip and pipe. Refer

to Figure 4 on page 5 for more information. Tighten the bolts to secure the pipe

clamp sensor to the pipe.

Figure 6. Sensor Tip and Pipe Contact

CorrectIncorrect

A. Sensor

B. Extension of pipe clamp

C. Pipe clamp

D. Pipe

Quick Start Guide

August 2017

2.1 Install transmitter

See appropriate transmitter reference manual for sensor-transmitter

installation. Refer to Figure 7 for sensor lead wire terminations.

Figure 7. Sensor Lead Wire Termination

2.2 Commission transmitter

See appropriate transmitter reference manual for transmitter commissioning

instructions.

3.0 Installing optional accessories

3.1 Corrosion protection inlay

The corrosion protection inlay provides a layer of protection to help minimize

the possibility of dissimilar metal corrosion between the pipe clamp and pipe.

The inlay is installed in between the pipe clamp and the pipe. Ensure the sensor

is clearing the hole in the protection inlay after installation. Refer to Figure 8 for

more information.

Single element 3-wire Single element 4-wire Dual element 3-wire

August 2017

Quick Start Guide

Figure 8. Pipe Clamp Sensor Assembly with Protection Inlay

3.2 Replacement sensor

The spring loaded sensor can be ordered for replacement using the Rosemount

0085 Pipe Clamp Sensor Product Data Sheet.

Use the following steps to replace the sensor.

1. Loosen and remove the original sensor from the extension of the pipe clamp.

2. Add pipe compound or PTFE tape (where local piping codes allow) to the

threads of the new sensor.

3. Insert the new sensor into the extension of the pipe clamp sensor and ensure

the sensor tip passes through the hole of the pipe clamp. Refer to Figure 6 for

more information.

4. Screw in the sensor and tighten to 24 ft-lbs of torque.

A. Extension of pipe clamp

B. Pipe clamp

C. Sensor

D. Corrosion protection inlay

E. Pipe

Quick Start Guide

August 2017

4.0 Rosemount X-well™Technology considerations

Rosemount X-well Technology is for temperature monitoring applications and is

not intended for control or safety applications. It is available in the Rosemount

3144P Temperature Transmitter and 648 Wireless Temperature Transmitter in a

factory assembled direct mount configuration with a Rosemount 0085 Pipe

Clamp Sensor. It cannot be used in a remote mount configuration.

Rosemount X-well Technology will only work as specified with factory supplied

and assembled Rosemount 0085 Pipe Clamp silver tipped single element sensor

with an 80 mm extension length. It will not work as specified if used with other

sensors. Installation and use of incorrect sensor will result in inaccurate process

temperature calculations. It is extremely important the above requirements and

installation steps below are followed to ensure Rosemount X-well Technology

works as specified.

In general, pipe clamp sensor installation best practices shall be followed (see

“Location and orientation” on page 3 for more details) as well as the specific

Rosemount X-well Technology requirements noted below.

Direct mounting of transmitter on pipe clamp sensor is required for

Rosemount X-well Technology to properly function. Figure 9 displays a

transmitter/pipe clamp assembly that is in a direct mount configuration.

Figure 9. Pipe Clamp Sensor Assembly in Direct Mount Configuration

Assembly shall be installed away from dynamic external temperature sources

such as a boiler or heat tracing.

August 2017

Quick Start Guide

The pipe clamp sensor makes direct contact with pipe surface. Moisture

buildup between sensor and pipe surface or sensor hangup in assembly can

cause inaccurate process temperature calculations. Refer to “Install pipe

clamp sensor” on page 6 for more information on proper sensor to pipe

surface contact.

Insulation at least 1/2-in. thick (with R-value of > 0.42 m2⫻K/W) is required

over the sensor clamp assembly and sensor extension up to transmitter head

to prevent heat loss. Apply a minimum of six inches of insulation on each side

of the pipe clamp sensor. Care should be taken to minimize air gaps between

insulation and pipe. See Figure 10 for more information.

Figure 10. Pipe Clamp Insulation

Note

DO NOT apply insulation over transmitter head.

Although it will come from the factory configured as such, ensure the pipe

clamp RTD sensor is assembled in the correct wire configuration. Refer to the

appropriate transmitter reference manual for correct wire configurations.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de Emerson

Emerson

Emerson Rosemount TupHFET TF396 Manual de usuario

Emerson

Emerson Net Safety SC311 Manual de usuario

Emerson

Emerson Rosemount Hx338+ Manual de usuario

Emerson

Emerson Liebert Xtreme Density Guía

Emerson

Emerson Rosemount 3500P Manual de usuario

Emerson

Emerson Rosemount 328A Manual de usuario

Emerson

Emerson Rosemount 8700 Series Manual de usuario

Emerson

Emerson Rosemount 0065 Manual de usuario

Emerson

Emerson Micro Motion Elite Coriolis CMF400 Manual de usuario

Emerson

Emerson Rosemount 372 Manual de usuario

Emerson

Emerson AVENTICS ST6 Manual de usuario

Emerson

Emerson Rosemount 3200HP Manual de usuario

Emerson

Emerson Rosemount 3300HT Manual de usuario

Emerson

Emerson Rosemount 3051S Series Manual de usuario

Emerson

Emerson Rosemount 140 Manual de usuario

Emerson

Emerson AutoSense II Inbound Standalone Manual de usuario

Emerson

Emerson Rosemount 214C Manual de usuario

Emerson

Emerson DVS205 Manual de usuario

Emerson

Emerson Fisher 249 Manual de usuario

Emerson

Emerson Mobrey Electrosensor Manual

Emerson

Emerson Rosemount 0065 Manual de usuario

Emerson

Emerson 203-5751 Manual de usuario

Emerson

Emerson Micro Motion F-Series Sensor Manual de usuario

Emerson

Emerson Rosemount 396 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario