Emerson Micro Motion H Series Manual de usuario
Installation Manual
20002346, Rev BD
October 2020
Micro Motion™ H-Series Hygienic Coriolis
Flow and Density Sensors
Safety messages
Safety messages are provided throughout this manual to protect personnel and equipment. Read each safety message carefully
before proceeding to the next step.
Safety and approval information
This Micro Motion product complies with all applicable European directives when properly installed in accordance with the
instructions in this manual. Refer to the EU declaration of conformity for directives that apply to this product. The EU declaration
of conformity, with all applicable European directives, and the complete ATEX Installation Drawings and Instructions are available
on the internet at www.emerson.com or through your local Micro Motion support center.
Information affixed to equipment that complies with the Pressure Equipment Directive, can be found on the internet at
www.emerson.com.
For hazardous installations in Europe, refer to standard EN 60079-14 if national standards do not apply.
Other information
Full product specifications can be found in the product data sheet. Troubleshooting information can be found in the configuration
manual. Product data sheets and manuals are available from the Micro Motion web site at www.emerson.com.
Return policy
Follow Micro Motion procedures when returning equipment. These procedures ensure legal compliance with government
transportation agencies and help provide a safe working environment for Micro Motion employees. Micro Motion will not accept
your returned equipment if you fail to follow Micro Motion procedures.
Return procedures and forms are available on our web support site at www.emerson.com, or by phoning the Micro Motion
Customer Service department.
Emerson Flow customer service
Email:
•Worldwide: [email protected]
•Asia-Pacific: [email protected]
Telephone:
North and South America Europe and Middle East Asia Pacific
United States 800-522-6277 U.K. and Ireland 0870 240 1978 Australia 800 158 727
Canada +1 303-527-5200 The Netherlands +31 (0) 70 413
6666
New Zealand 099 128 804
Mexico +52 55 5809 5010 France +33 (0) 800 917
901
India 800 440 1468
Argentina +54 11 4809 2700 Germany 0800 182 5347 Pakistan 888 550 2682
Brazil +55 15 3413 8000 Italy +39 8008 77334 China +86 21 2892 9000
Chile +56 2 2928 4800 Central & Eastern +41 (0) 41 7686
111
Japan +81 3 5769 6803
Peru +51 15190130 Russia/CIS +7 495 995 9559 South Korea +82 2 3438 4600
Egypt 0800 000 0015 Singapore +65 6 777 8211
Oman 800 70101 Thailand 001 800 441 6426
Qatar 431 0044 Malaysia 800 814 008
Kuwait 663 299 01
South Africa 800 991 390
Saudi Arabia 800 844 9564
UAE 800 0444 0684
2
Contents
Chapter 1 Before you begin........................................................................................................5
1.1 About this document...................................................................................................................5
1.2 Hazard messages.........................................................................................................................5
1.3 Related documentation............................................................................................................... 6
Chapter 2 Planning.................................................................................................................... 7
2.1 Installation checklist.................................................................................................................... 7
2.2 Best practices.............................................................................................................................. 8
2.3 Temperature limits...................................................................................................................... 8
2.4 Recommendations for hygienic and self-draining applications.....................................................9
Chapter 3 Mounting.................................................................................................................11
3.1 Mount the sensor.......................................................................................................................11
3.2 Attach extended electronics...................................................................................................... 11
Chapter 4 Transmitter power and I/O wiring............................................................................ 13
4.1 Options for wiring......................................................................................................................13
4.2 Connect 4-wire cable................................................................................................................. 13
4.3 Connect the 9-wire cable .......................................................................................................... 17
Chapter 5 Grounding................................................................................................................19
Chapter 6 Supplementary information.....................................................................................21
6.1 Purge the sensor case ................................................................................................................21
6.2 Pressure relief............................................................................................................................ 22
Installation Manual Contents
20002346 October 2020
Installation Manual 3
Contents Installation Manual
October 2020 20002346
4 Micro Motion H-Series
1 Before you begin
1.1 About this document
This document provides information on planning, mounting, wiring, and grounding the H-
Series sensor.
The information in this document assumes that users understand basic transmitter and
sensor installation, configuration, and maintenance concepts and procedures.
1.2 Hazard messages
This document uses the following criteria for hazard messages based on ANSI standards
Z535.6-2011 (R2017).
DANGER
Serious injury or death will occur if a hazardous situation is not avoided.
WARNING
Serious injury or death could occur if a hazardous situation is not avoided.
CAUTION
Minor or moderate injury will or could occur if a hazardous situation is not avoided.
NOTICE
Data loss, property damage, hardware damage, or software damage can occur if a
situation is not avoided. There is no credible risk of physical injury.
Physical access
NOTICE
Unauthorized personnel can potentially cause significant damage and/or misconfiguration
of end users' equipment. Protect against all intentional or unintentional unauthorized use.
Physical security is an important part of any security program and fundamental to
protecting your system. Restrict physical access to protect users' assets. This is true for all
systems used within the facility.
Installation Manual Before you begin
20002346 October 2020
Installation Manual 5
1.3 Related documentation
You can find all product documentation on the product documentation DVD shipped with
the product or at www.emerson.com.
See any of the following documents for more information:
•The hazardous area approvals documentation shipped with the sensor or available at
www.emerson.com/flowmeasurement.
•Micro Motion H-Series Hygienic Coriolis Flow and Density Meters Product Data Sheet
•Micro Motion 9-Wire Flow Meter Cable Preparation and Installation Guide
•The transmitter installation and configuration and use guides
Before you begin Installation Manual
October 2020 20002346
6 Micro Motion H-Series
2 Planning
2.1 Installation checklist
□Make sure that the hazardous area specified on the approval tag is suitable for the
environment in which the meter will be installed.
WARNING
Failure to abide by approvals can cause an explosion resulting in injury or death.
□Verify that the local ambient and process temperatures are within the limits of the
meter.
□If your sensor has an integral transmitter, no wiring is required between the sensor and
transmitter. Follow the wiring instructions in the transmitter installation manual for
signal and power wiring.
□If your transmitter has remote-mounted electronics, follow the instructions in this
manual for wiring between the sensor and the transmitter, and then follow the
instructions in the transmitter installation manual for power and signal wiring.
Table 2-1: Maximum cable lengths
Cable type To transmitter Maximum length
Micro Motion
4-wire
All 4-wire MVD transmitters 1,000 ft (305 m) without Ex-approval
500 ft (152 m) with IIC-rated sensors
1,000 ft (305 m) with IIB-rated sensors
Table 2-2: Maximum lengths for user-supplied 4-wire cable
Wire function Wire size Maximum length
Power (VDC) 22 AWG (0.326 mm²) 300 ft (91 m)
20 AWG (0.518 mm²) 500 ft (152 m)
18 AWG (0.823 mm²) 1,000 ft (305 m)
Signal (RS-485) 22 AWG (0.326 mm²) or larger 1,000 ft (305 m)
□For optimal performance, install the sensor in the preferred orientation. The sensor will
work in any orientation as long as the flow tubes remain full of process fluid.
Installation Manual Planning
20002346 October 2020
Installation Manual 7
Table 2-3: Preferred sensor orientation
Process Preferred orientation Secondary preferred
orientation(1)
Alternate suitable
orientation(1)
Liquids &
slurries
Gases
(1) For meters installed in a horizontal orientation it is recommended to utilize forced expulsion
with pressurized gas where draininability is required.
□Install the meter so that the flow direction arrow on the sensor case matches the actual
forward flow of the process. (Flow direction is also software-selectable.)
2.2 Best practices
The following information can help you get the most from your sensor.
•There are no pipe run requirements for Micro Motion sensors. Straight runs of pipe
upstream or downstream are unnecessary.
•If the sensor is installed in a vertical pipeline, liquids and slurries should flow upward
through the sensor. Gases should flow downward.
•Keep the sensor tubes full of process fluid.
•For halting flow through the sensor with a single valve, install the valve downstream
from the sensor.
•The sensor does not require external supports. The flanges will support the sensor in
any orientation.
2.3 Temperature limits
Sensors can be used in the process and ambient temperature ranges shown in the
temperature limit graphs. For the purposes of selecting electronics options, temperature
limit graphs should be used only as a general guide. If your process conditions are close to
the gray area, consult with your Micro Motion representative.
Note
•In all cases, the electronics cannot be operated where the ambient temperature is
below -40 °F (-40.0 °C) or above 140 °F (60.0 °C). If a sensor is to be used where the
ambient temperature is outside of the range permissible for the electronics, the
Planning Installation Manual
October 2020 20002346
8 Micro Motion H-Series
electronics must be remotely located where the ambient temperature is within the
permissible range, as indicated by the shaded areas of the temperature limit graphs.
•Temperature limits may be further restricted by hazardous area approvals. Refer to the
hazardous area approvals documentation shipped with the sensor or available from the
www.emerson.com/flowmeasurement. For further questions, contact customer
service.
•The extended-mount electronics option allows the sensor case to be insulated without
covering the transmitter, core processor, or junction box, but does not affect
temperature ratings. When insulating the sensor case at elevated process
temperatures (above 140 °F (60.0 °C)), please ensure electronics are not enclosed in
insulation as this may lead to electronics failure.
Ambient and process temperature limits for all H-Series meters
400
(204)
81
(27)
–148
(–100) Tproc
140 (60)
158 (70)
–40 (–40)
A
B
Tamb
A. All available electronic options
B. Extended or remote mount electronics only
Tamb Ambient temperature °F (°C)
Tproc Process temperature °F (°C)
2.4 Recommendations for hygienic and self-
draining applications
H-Series sensors are self-draining when installed in a vertical pipeline.
For optimal cleanability and drainability:
•If possible, install the sensor in a vertical pipeline with the process fluid flowing upward
through the sensor.
•If the sensor must be installed in a horizontal pipeline, drainage is accomplished by air
purge evacuation of the pipeline circuit.
•For clean-in-place (CIP) applications, Micro Motion recommends using the generally-
accepted flow velocity of at least 1.5 m/s for cleaning the sensor.
•The gap between the electronics housing and sensor body should be inspected
periodically. Manually clean this gap when necessary.
Installation Manual Planning
20002346 October 2020
Installation Manual 9
•Tri-Clamp® and DIN 11851 style process connections require special gaskets to comply
with EHEDG requirements for hygienic design.
Figure 2-1: Installation for self-draining applications
A
B
C
A. Process pipeline
B. Direction of normal process flow
C. Direction of drainage
Planning Installation Manual
October 2020 20002346
10 Micro Motion H-Series
Otros manuales para Micro Motion H Series
1
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Otros manuales de Accesorios de Emerson
Emerson
Emerson Rosemount 389 Manual de usuario
Emerson
Emerson AVENTICS ST6 Manual de usuario
Emerson
Emerson Rosemount 214C Manual de usuario
Emerson
Emerson Rosemount 0065 Manual de usuario
Emerson
Emerson Micro Motion LF Series Manual de usuario
Emerson
Emerson Rosemount 328A Manual de usuario
Emerson
Emerson Micro Motion ELITE CMF200A Manual de usuario
Emerson
Emerson Net Safety SC311 Manual de usuario
Emerson
Emerson Rosemount 140 Manual de usuario
Emerson
Emerson Rosemount 3200HP Manual de usuario
Emerson
Emerson MRLDS Manual de usuario
Emerson
Emerson Mobrey Electrosensor Manual
Emerson
Emerson Rosemount 628 Manual de usuario
Emerson
Emerson Rosemount 396P Manual de usuario
Emerson
Emerson Rosemount 3300HT Manual de usuario
Emerson
Emerson Rosemount 396 Manual de usuario
Emerson
Emerson Rosemount 385 Manual de usuario
Emerson
Emerson Rosemount 0065 Manual de usuario
Emerson
Emerson Micro Motion Elite Coriolis Micro Motion Elite Coriolis... Manual de usuario
Emerson
Emerson Rosemount Volume 1 Manual de usuario
