Emcotec RC Electronic DPSI LCD Manual de usuario

DPSI LCD Operating Instructions Version 1.0

Page 2 of 32

Contents

1. Preface .............................................................................................3

2. Characteristics ................................................................................ 4

3. Display- and Control-Elements......................................................6

4. Dimensions......................................................................................7

5. Assembly ......................................................................................... 8

6. Push-Buttons and LED-Indicators................................................. 9

6.1. Functions of Buttons................................................................9

6.2. Functions of LEDs .................................................................10

7. Readouts of the LC-Display ......................................................... 13

7.1. Readout after Power-On........................................................14

7.2. Readout of Receiver Information...........................................15

7.3. Readout of Receiver Errors ...................................................18

7.4. Readout of the Current Supply ..............................................19

7.5. Readout of Current Supply Errors .........................................21

8. Resetting Stored Values...............................................................22

9. Programming / Setup.................................................................... 23

9.1. Programming Options............................................................24

9.2. Operating Mode.....................................................................25

9.3. Switching Positions Failsafe..................................................26

9.4. Switching Positions Master/Slave..........................................27

9.5. Units.......................................................................................28

9.6. Battery Type ..........................................................................28

9.7. Buzzer On/Off........................................................................29

9.8. Language...............................................................................29

9.9. Factory Settings.....................................................................30

9.10. Exit / Return.........................................................................30

10. Technical Data of DPSI LCD.......................................................30

11. Warranty.......................................................................................31

DPSI LCD Operating Instructions Version 1.0

Page 3 of 32

1. Preface

With the DPSI LCD you purchased a high grade, modern and secure

product. We appreciate your trust!

Long lasting experience for years in development and manufacturing of

electronically systems as well as the knowledge of the world’s best

model airplane pilots has influenced the development. All products are

developed by experienced engineers and manufactured at EMCOTEC

GmbH in Germany on our own production line. Extensive optically and

electronically end tests for every system, which leaves our house,

assure that you, our customer acquire an absolute reliable product,

which considerably increases the reliability of your valuable RC-Model.

Of course, the DPSI LCD (just like all products from EMCOTEC) not

only has been tested extensively in the laboratory, but also went

through intensive flight-testing. Like done in the automobile industry an

FMEA (Failure Mode and Effect Analysis) reduces the possibility of

damage and malfunction on operating errors to a minimum.

Hint:

We kindly ask you to read these operating instructions carefully and observe the

installation hints. Thus, errors can be avoided in advance.

We are all ears for your wishes and questions. Challenge us!

Bobingen, January 2008

The Staff of EMCOTEC GmbH

DPSI LCD Operating Instructions Version 1.0

Page 4 of 32

2. Characteristics

The DPSI LCD serves as an optional extension to DPSI products,

which can control a LC-Display:

•DPSI receiver switch (e.g. TWIN Mini stand alone)

•DPSI dual current supply (e.g. entire TWIN Mini)

•Additional future products

It displays (dependent on DPSI base system) important information in

plain text which is gathered during operation. These is information

about

•Signal quality of the receiver

•Supply voltage of receiver (batteries)

•Withdrawn capacities from batteries

•Current flow in receiver equipment

and much more.

Due to the integrated LEDs system states can be realized immediately

without first reading the text in the display. Critical situations are

indicated by quickly blinking LEDs. Root cause can than be read from

the display.

Three push buttons serve as display selectors or serve for setting up

options. It was never easier to display different data or set up diverse

options. The optimized handling concept was evaluated in practical

studies and is therefore nearly self explaining.

The DPSI LCD can also serve as On/Off switch for certain products of

the EMCOTEC DPSI program, thereby eliminating the need for the

regular switch actuator.

The DPSI LCD is mounted into the model just like a cockpit instrument.

In this way, a functional handling and display unit results, upgrading

the overall picture of the model by these small dimensions and a

shapely housing.

DPSI LCD Operating Instructions Version 1.0

Page 5 of 32

There is a 6-pin connector in the center of the back side of the DPSI

LCD for a connection cable. The connection cable (4-pin or 6-pin

depending on DPSI base system) is simply connected to the 6-pin

connector. Reverse polarity is impossible.

The other side of the cable is connected to the corresponding DPSI

system (e.g. DPSI TWIN Mini). Here, polarity must be observed. The

red wire is “positive” and must be “congruent” with the corresponding

markings (+) at the base system (see picture).

DPSI LCD Operating Instructions Version 1.0

Page 6 of 32

3. Display- and Control-Elements

DPSI LCD Operating Instructions Version 1.0

Page 7 of 32

4. Dimensions

DPSI LCD Operating Instructions Version 1.0

Page 8 of 32

5. Assembly

The DPSI LCD can be used as a cockpit instrument. Cut a squared

hole of 57mm edge length and 6mm inner radii into the cockpit (or

similar mounting plate). The DPSI LCD is then to be fed through the

hole from back to front (!) and secured using 4 regular M3 screws. The

screws are self cutting and find sufficient material in the plastic of the

mounting latches. Screw distance is 60mm.

Drilling template 1:1 scale:

DPSI LCD Operating Instructions Version 1.0

Page 9 of 32

6. Push-Buttons and LED-Indicators

6.1. Functions of Buttons

Depending on the used or connected DPSI system, the three push

buttons of the DPSI LCD can be used as On/Off switch (e.g. for the

DPSI TWIN Mini including adapted dual power supply).

Turning on is accomplished by pushing the “SET”-button. Turning off is

done by pushing the “DOWN” () and “UP” () buttons simultaneously

(!) for about 2 seconds.

When turned on, the buttons work for conforming entries (“SET”) or for

selections of information from the display “DOWN” () and “UP” ().

By pushing the “UP”- or “DOWN”-buttons multiple times, the menu

(one frame with text) advances.

There are some particular features in the layout of the buttons:

1.) If the “SET”-button is permanently pushed for about 5 seconds

during turning the power on, the system changes into programming

mode (setup). Here, several setups for the system can be

accomplished.

2.) If during operation first the “UP”-button () and additionally the

“SET”-button is pushed, memorized information can be deleted (reset

menu).

3.) If the “SET”-button is pushed during operation, all LEDs will be

turned off. After pushing this button again, the LEDs are turned back

on again. The ultra bright LEDs are very well recognizable even in

bright day light. If the ambient light is dim, the LEDs glare which cause

difficulties to read the display. Therefore, the LEDs can be turned off.

DPSI LCD Operating Instructions Version 1.0

Page 10 of 32

Function Buttons

Turning DPSI on * Push SET momentarily

Turning DPSI off * Push  + for 2 seconds simultaneously

Turning LEDs off Push SET momentarily during operation

Turning LEDs on Push SET momentarily during operation

Start setup Push SET during power on for 5 sec.

Reset menu Push  , then press SET simultaneously

* Not possible with all systems!

6.2. Functions of LEDs

After turning the DPSI LCD on, all eight LEDs are turned on

temporarily from left to right in order to test their functioning.

The LEDs have different meanings and therefore are assigned

distinctive groups. Depending on the connected system, the LEDs

have an assigned function or not. If e.g. there is no receiver switching

unit installed in the system, the corresponding LEDs (green and blue)

are not used. If no power supply is integrated into the system, the red

and yellow LEDs are not used.

Assignment of the LEDs (top view onto display)

Battery 1 Receiver 1 Battery 2 Receiver 2

Red Yellow Green Blue Red Yellow Green Blue

•The red and yellow LEDs are assigned to battery faults

•The green and blue LEDs are assigned to receiver (errors)

Red means: Error (Danger)

Yellow means: Warning

Green means: All ok

Blue means: Additional information (which receiver is active)

Tabla de contenidos

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario