EMC DS-16B Manual de usuario
EMC Departmental Switch DS-16B Installation Guide
1
This document explains the power, cooling, weight, and rack placement
requirements for the 16-port EMC departmental switch shown in Figure
1. It also describes the kits available for mounting them in EMC and
non-EMC Racks and includes installation instructions as well.
Major sections are
• Device Power, Cooling, and Weight Information................................. 3
• Device Dimensions.................................................................................... 3
• Device Placement Requirements............................................................. 4
• Switch Mounting Kit (DS16B2 - RKH/RKL)......................................... 5
• Installing the DS-16B2 Rails................................................................... 10
• Installing the DS-16B2 Switch................................................................ 21
EMC Departmental Switch
DS-16B2
Installation Guide
P/N 014003075-A01
Device Device Model Mounting Kit Model
16-port departmental switch DS-16B2-0D DS16B2-RKH
DS16B2-RKL
2
EMC Departmental Switch DS-16B2 Installation Guide
Figure 1 DS-16B2 16-Port Switch
EMC2041
EMC Departmental Switch DS-16B2 Installation Guide
3
Device Power, Cooling, and Weight Information
Device Power, Cooling, and Weight Information
Device Dimensions
Device Power Requirements Cooling Requirements
(Heat Dissipation) Maximum Weight
DS-16B2 switch Voltage: 100 to 240 V ac, 47 to 63 Hz 368.5 BTU/hr 12.9 kg (28.5 lbs)
Device Height Depth Width
DS-16B2 switch 4.34 cm 1.71 in 61.00 cm 24.01 in 42.86 cm 16.87 in
DS-16B2 switch
with rails 1.0 U 4.44 cm 1.75 in 61.00 cm 24.01 in 43.18 cm 17.00 in
4
EMC Departmental Switch DS-16B2 Installation Guide
Device Placement Requirements
Device Placement Requirements
There are no restrictions on the location of the DS-16B2 switch in the
rack/cabinet.
Switches are typically located at the top of the rack/cabinet in pairs.
Power distribution must support the number of outlets required for
the switch and the switch power rating listed in the table on page 3.
Figure 2 Sample Cabinet Installation
EMC2056
Fr
o
nt R
ea
r
Switch (1 U)
Switch (1 U)
DAE (3.5 U)
DAE (3.5 U)
DAE (3.5 U)
DAE (3.5 U)
DAE (3.5 U)
DAE (3.5 U)
DAE (3.5 U)
DAE (3.5 U)
DPE (6.5 U)
Filler Panel (2 U)
SPS (1 U)
39 U
Note:
S
witch bezels are
removed for clarity.
EMC Departmental Switch DS-16B2 Installation Guide
5
Switch Mounting Kit (DS16B2 - RKH/RKL)
Switch Mounting Kit
(DS16B2 - RKH/RKL)
The switch mounting kit includes rails, bezel, and power cords as
listed in the table below.
See the figure below for an illustration of these components.
Component Use
2 switch mounting brackets - see illustration on page 21. 2 per switch
2 short rail assemblies (20.5 inches to 27 inches) 2 per switch
2 long rail assemblies (27 inches to 34 inches) 2 per switch
1 U standard-profile or low-profile bezel (front rack panel) 1 per switch
Bezel supports 2 per switch
2 8-foot IEC power cords, straight C13 to C14 straight
2 7.5-foot USA power cords, straight C13 to N5-15P straight (with the
DS-16B2-RKL kit only)
2 per switch
(use the ones appropriate for your PDU)
6
EMC Departmental Switch DS-16B2 Installation Guide
Switch Mounting Kit (DS16B2 - RKH/RKL)
Figure 3 Rails. Bezel, and Power Cords
EMC2042
Front
Rails
Short
Rear
Rails
Long
Rear
Rails
Switch
Mounting
Brackets
Ac Power
Cords
Bezel
Bezel
Supports
EMC Departmental Switch DS-16B2 Installation Guide
7
Switch Mounting Kit (DS16B2 - RKH/RKL)
Screws, Nuts and Washers
See the table below for a detailed list of all the securing hardware that
is included in the switch mounting kit.
The rail assemblies for the EMC CLARiiON®rack come pre-assembled, with
the power cord in the rail. Only the long rails, used in third party
racks/cabinets, must be assembled.
8
EMC Departmental Switch DS-16B2 Installation Guide
Switch Mounting Kit (DS16B2 - RKH/RKL)
Component Use
#10 flat washer (Qty. 6) 2 per rail assembly to secure adjustable
rail to the “C” channel.
1 per ball stud.
M5 keps nut (Qty. 4) 2 per rail assembly to secure adjustable
rail to the “C” channel.
8-32 x 5/16-in. pan-head screw (Qty. 6) 3 per mounting bracket to secure
mounting bracket to switch.
M5 x 10-mm pan-head screw (Qty. 8) 4 per rail for DS-16B2 in round-hole
channels.
Square-hole washer (Qty. 8) 4 per rail for DS-16B2 in square-hole
channels.
M5 x 16-mm flat-head screw (Qty. 8) 4 per rail for DS-16B2 in square-hole
channels.
M3 x 8-mm pan-head screw (Qty. 6) 1 per switch mounting bracket. Used to
secure mounting brackets to the rails.
2 per bezel support, to secure the bezel
support to the rail assembly.
Ball stud (Qty. 2) 2 per bezel, to secure the bezel to the
rail assembly.
EMC Departmental Switch DS-16B2 Installation Guide
9
Switch Mounting Kit (DS16B2 - RKH/RKL)
Tools Required for Installation
You will need the following tools to complete the installation of the
rails and switch(es).
EMC2065
Tools Required:
#1 Phillips
Screwdriver
8mm (5/16-in.)
Nut Driver
6-mm (1/4-in.)
Nut Driver
10
EMC Departmental Switch DS-16B2 Installation Guide
Installing the DS-16B2 Rails
Installing the DS-16B2 Rails
This section describes the installation procedures for the DS-16B2
rails. Figure 4 shows a view of the rails installed in a 39 U
rack/cabinet.
Figure 4 View of the Rails Installed in a 39 U Rack/Cabinet
EMC2071
Fr
o
nt Rear
Rear Door
Removed for
Clarity
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de EMC
EMC
EMC Connectrix DS-32M2 Manual de usuario
EMC
EMC Connectrix B Series Manual de usuario
EMC
EMC Connectrix ED-64M Manual de usuario
EMC
EMC Connectrix DS-32M2 Manual de usuario
EMC
EMC Connectrix B Series Guía rápida de usuario
EMC
EMC Connectrix B Series Guía rápida de usuario
EMC
EMC Connectrix B Series Guía rápida de usuario
EMC
EMC Connectrix B Series Guía rápida de usuario
EMC
EMC Connectrix B Series Guía rápida de usuario
EMC
EMC Connectrix DS-24M2 Manual de usuario
