Eltima electronic 50051 Manual de usuario

Assembly instructions

eltima carrier systems

version: 11.2017

2 Part list

Part list

Profile rail 20 x 20 mm

Angle clamp bracket

Profile rail 20 x 40 mm

Angle bracket

Cover cap for

angle bracket

Cap screws M5 x 8,

for angle bracket

t-slot nut

Lenshead screw M5 x 10

Allen key

3 mm

Large corner plate

Small corner plate

¼“ screw

3 Content

Content

Part list..................................................................................................... 2

Content .................................................................................................... 3

Introduction.............................................................................................. 4

Intended use.................................................................................................. 4

Symbols ......................................................................................................... 4

Assembly technology ................................................................................ 5

Inserting the T-slot nut.................................................................................. 5

Corner connections ....................................................................................... 6

Cross connections.......................................................................................... 8

Carrier system for experimental photography............................................ 9

Carrier system for bird photography........................................................ 15

Carrier for insect photography................................................................. 16

Notices ................................................................................................... 18

4 Introduction

Introduction

Dear customer,

thank you for purchasing the eltima carrier system. It should be a flexible and

reliable tool for you.

If you have any wishes and suggestions for improvement, do not hesitate and

let us know. Thus this product can grow and meet your requirements.

Please read these assembly instructions carefully before using the carrier sys-

tem. It will help you to familiarize with the structure and operation of this

system. This way you can fully exploit the benefits it offers you.

Intended use

The eltima carrier system has been developed for the mounting and fixing of

light barriers, light barrier accessories and other photographic accessories.

Use it only for this purpose.

Symbols

Tips for handling the device.

Important note on the function of the device.

Important note to avoid damage to the device or connected devices.

5 Assembly technology

Assembly technology

This section describes the basic handling and assembly methods of the car-

rier system.

Inserting the T-slot nut

Profile rails, angle brackets and corner plates are bolt together by the means

of screws and T-slot nuts.

Place the T-slot nut with one edge ahead into the slot of a rail, like depicted

in Figure 1.

Then press the nut completely into the slot, like shown in Figure 2.

Push the second edge of the nut into the slot. The T-slot nut is now in posi-

tion, held by the spring-mounted ball of the nut, see Figure 3.

You can now move the T-slot nut to the right position by using a tool,

e.g. the included Allen key.

Figure 1: Placing the T-slot nut into the rail

Figure 2: inserting the second edge of the nut into the slot

Figure 3: T-slot nut in position

6 Assembly technology

Corner connections

Two profile rails are connected by the means of angle brackets.

At first, insert two T-lot nuts at the end of the slot, see Figure 6.

The two threads of the nuts should point to the ends of the rail. This

is important, so that the angle can subsequently be pushed all the way

to the end of the rail.

Screw the bracket firstly with the outer screw, by turning it 1 to 2 turns, so

the bracket will still be loose, see Figure 5.

Then slide the bracket with the remaining hole over the second slot nut and

also loosely tighten the second screw, see Figure 4.

Now push the angle to the end of the rail.

Figure 6:

inserting the T-slot nuts

Figure 5:

insertig the first screw

Figure 4:

inserting the second screw

7 Assembly technology

Insert as shown in Figure 6 two T-slot nuts in the slot of the second rail. Screw

the bracket as shown in Figure 4 on the second rail, but do not tighten the

screws. The two rails are now loosely connected, see Figure 7.

Slide the rails to the desired position and tighten the screws, see Figure 8.

Insert the cover cap by pushing it firmly into the bracket, see Figure 9.

Figure 7:

joining two rails

Figure 8:

aligning the rails

Figure 9:

tightened corner connec-

tion

8 Assembly technology

Cross connections

Insert a T-slot nut at the desired position into the slot of a rail. Screw it loose

into the nut using a M5x10 lens head screw, see Figure 11.

At first just turn the screw by one turn. The bracket will hang loosely

and you can hook the rail easily into the bracket.

Hook the cross profile into the bracket at the right position and tighten the

screw, see Figure 10.

Figure 11: mounting the clamp bracket

Figure 10: completed cross connection

9 Carrier system for experimental photography

Carrier system for experimental photography

Bolt up two assemblies consisting of one rail 20x40x600 mm and one

20x40x1200 mm, like shown in Figure 13.

The assemblies will form the support frames of the carrier system.

Bolt up three 20x20x600 mm rails to a frame like shown in Figure 12. The

spacing between the vertical rail and the end of the horizontal rail should be

app. 20 mm, i.e. breadth of a rail.

This will be the carrier for the light barrier, as far as needed.

Figure 13: Aufbau der seitlichen Stützen

Figure 12: Aufbau des Trägers für die Lichtschranke

ca. 20 mm

10 Carrier system for experimental photography

Bolt up two 20x20x600 mm rails and one 20x40x600 mm rail to a frame like

shown in Figure 15. The spacing between the vertical rail and the end of the

horizontal rail should be app. 20 mm, i.e. breadth of a rail.

This frame will form the carrier for the drop dispenser.

Bold a 20x20x600 mm rail on the flushly mounted side of the drop dispenser

frame, like shown on the right side of the Figure 14.

The clamp brackets must be mounted on opposite sides of the cross profile,

see the left side of Figure 14.

ca. 20 mm

Figure 15: Aufbau des Trägers für die Tropfenspender

Figure 14: Befestigung des Querprofils

Flushly mounted

side

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario

eltima electronic 50051 Manual de usuario

Manuales populares de Cámara digital de otras marcas