ELTEX WEP-12ac Manual de usuario

IP address:192.168.1.10

Username:admin

Password:password



    

   Wireless access point

 WEP-12ac

   User manual

    Firmware version1.16.0

WEP-12ac user manual

 2

Contents

1 Introduction ............................................................................................................................................ 4

1.1 Annotation...........................................................................................................................................4

1.2 Symbols...............................................................................................................................................4

2 Device description ................................................................................................................................. 5

2.1 Purpose ...............................................................................................................................................5

2.2 Device specification............................................................................................................................5

2.3 The device technical parameters.......................................................................................................7

2.4 Design..................................................................................................................................................8

2.4.1 Device main panel........................................................................................................................... 8

2.5 Light indication....................................................................................................................................9

2.6 Reset to the default settings ..............................................................................................................9

2.7 Delivery package...............................................................................................................................10

3 Installation order.................................................................................................................................. 11

3.1 Safety rules........................................................................................................................................11

3.2 Installation recommendations .........................................................................................................11

3.3 Calculating the number of required access points.........................................................................11

3.4 Installing WEP-12ac..........................................................................................................................14

3.4.1 Order for wall-mounting brackets ................................................................................................ 14

3.4.2 Installing to false ceiling............................................................................................................... 15

3.4.3 Removing the device from the bracket........................................................................................ 15

4 Application A. WEP-12ac antennas patterns ..................................................................................... 16

5 Application B. Pin array of the device connectors............................................................................. 17

6 The list of changes .............................................................................................................................. 18

 WEP-12ac user manual

1 Introduction

1.1 Annotation

Modern tendencies of telecommunication development necessitate operators to search for the most optimal

technologies, allowing you to satisfy drastically growing needs of subscribers, maintaining at the same time

consistency of business processes, development flexibility and reduction of costs of various services provision.

Wireless technologies are spinning up more and more and have paced a huge way for short time from unstable

low-speed communication networks of low radius to broadband networks equitable to speed of wired networks

with high criteria to the quality of provided services. WEP-12ac device is a Wi-Fi access point of Enterprise class.

The device is dedicated to be installed inside buildings as an access point and to create a seamless wireless

network using several identical access points on a large area.

This manual specifies intended purpose, main technical parameters, design, installation procedure, safe operation

rules and installation recommendations forWEP-12ac.

1.2 Symbols

Notes and warnings

Notes contain important information, tips or recommendations on device operation and setup.



Warnings are used to inform the user about harmful situations for the device and the user alike, which

could cause malfunction or data loss.



 WEP-12ac user manual

2 Device description

2.1 Purpose

WEP-12ac wireless access point (hereinafter the device) is designed for provision of users' access to high-speed

safe network. The device is dedicated to create L2 wireless networks interfacing with a wired network. WEP-12ac

is connected to a wired network via 10/100/1000M Ethernet interface and arrange high-speed access to the

Internet for devices supporting Wi-Fi technology at 2.4 and 5 GHz. The device has two radio interfaces to organize

two physical wireless networks.

WEP-12ac supports up-to-date requirements to service quality and allows transmittingmore important traffic in

higher priorities queues. Prioritization is based on main QoS technologies: CoS (special tags in VLAN packet field)

and ToS (tags in IP packet field). Besides the standard methods of prioritization, the device allows you to assign

demands for traffic transmission almost in every packet field from MAC to TCP/UDP port. The ACL rules and

shaping allow you to control access, quality of service and restrictions for all subscribers as well as for each

subscriber individually. 

WEP-12ac is designed to be installed in offices, state buildings, conference halls, laboratories, hotels, etc. The

creation of virtual access points with different types of encryption allows clients to delimit access rights among

users and groups of users.

2.2 Device specification

Interfaces:

•2 Ethernet ports of 10/100/1000Base-T, 1 port out them supports PoE+ technology

•Console RJ-45;

Functions:

WLAN capabilities:

•support for IEEE 802.11a/b/g/n/ac standards;

•data aggregation, including A-MPDU (Tx /Rx) and А-MSDU (Rx);

•WMM-based priorities and packet planning;

•dynamic frequency selection (DFS);

•support for hidden SSID;

•32 virtual access points;

•third-party access point detection;

•support for Work Group Bridge.

•WDS;

•Mesh support;

•APSD;

Network functions:

•autonegotiation of speed, duplex mode and switching between MDI and MDI-X modes;

•support for VLAN;

•authentication support 802.1X;

•support for 802.11r;

•DHCP client;

•support for IPv6;

•LLDP;

•ACL;

•SNMP;

•GRE.

 WEP-12ac user manual

Cluster operation mode:

•organizing a cluster with capacity of up to 64 access points;

•auto synchronization of access point configurations in a cluster;

•auto update of access points firmware in a cluster;

• Single Management IP – united address to control access points in a cluster;

•autodistribution of frequency channels among access points;

•autodistribution of output power level among access points.

QoS functions

•priority and profile-based packet scheduling;

•bandwidth limiting for each SSID;

•changing WMM parameters for each radio interface.

Safety

•e-mail notifying on system events;

•centralized authorization via RADIUS server (WPA Enterprise);

•WPA/WPA2;

•Captive Portal;

•IPsec.

The figure below shows WEP-12ac application scheme.

WEP-12ac application scheme

 WEP-12ac user manual

2.3 The device technical parameters

Table 1 – The device main technical parameters

WAN Ethernet interface parameters

Number of ports 2

electrical connectors RJ-45

Data rate, Mbps 10/100/1000, auto-negotiation

Standards BASE-T

Wireless interface parameters

Standards 802.11a/b/g/n/ac

Frequency range, MHz 2412–2472 MHz, 5150–5850 MHz

Modulation CCK, BPSK, QPSK, 16QAM, 64QAM, 256QAM

Operating channels • 802.11b/g/n: 1–13 (2412–2472 MHz)

• 802.11a/ac: 36-64 (5180–5320 MHz)

• 100-144 (5500–5720 MHz)

• 149-165 (5745–5825 MHz)

Speed of data transmission, Mbps 6, 9, 12 , 18, 24, 36, 48, 54, MCS0-MCS23, MCS0-9 NSS1, MCS0-9 NSS2, MCS0-9

NSS3

802.11n:

• up to 216.7 Mbps (20 MHz channel),

•up to 450 Mbps (40 MHz channel)

802.11ac:

•up to 1300 Mbps (80 MHz)

Maximum output power of the

transmitter

•2.4 GHz up to 19 dBm

•5 GHz up to 19 dBm

(Defined by Transmit Power Limit and Transmit Power Control regulators)

Receiver sensitivity •2.4 GHz up to -98 dBm

•5 GHz up to -94 dBm

Safety •centralized authorization via RADIUS server (WPA Enterprise)

•64/128/152-bit WEP data encryption, WPA/WPA2

•Support for Captive Portal

•E-mail notifying on system events;

Dual-band antennas

 WEP-12ac user manual

Support for 3х3 MIMO

Two embedded Broadcom chips BCM43460

Control

Remote control Web interface, Telnet, SSH, SNMP, EMS management system. Firmware updating

and configuring through DHCP Autoprovisioning

Access restriction by password, by IP address

General parameters

Processor Broadcom BCM53016/BCM58522

NAND 128 MB NAND Flash

RAM 256 MB RAM DDR3

Power supply •power adapter 12 VDC, 2 А

•PoE+ - 48V/54V (IEEE 802.3at-2009)

Power consumption up to 14 W

Range of operation temperatures from +5 to +40°С

Relative humidity at 25°Сup to 80%

Dimensions 224x235x42 mm

Weight 0.3 kg

2.4 Design

WEP-12ac enclosed in plastic case.

2.4.1 Device main panel

The layout of WEP-12ac is shown in the figure below.

WEP-12ac main panel layout

Connectors and controls located on the device main panel are listed inTable 2.

 WEP-12ac user manual

Table 2 – Description of ports and controls

Front panel elementsDescription

1 Wi-Fi Operation indicators of corresponding Wi-Fi modules

2 12 V Connector for power supply

3 Console Connector for console cable connection (RJ-45 connector)

4 LAN 2 ports of 10/100/1000Base-T (RJ-45 connector) GE1 port for power supply connection via

PoE+

5 F Functional key

2.5 Light indication

The current device state is displayed by Wi-Fi, LAN, Power indicators. The list of indicators' possible states is

given below.

Table 3 – Light indication of device state

Indicator Indicator's status Device state

Wi-Fi  solid green Wi-Fi network is enabled

flashing green the process of data transmission trough a wireless network

LAN  solid green (10, 100 Mbps)/ solid orange

(1000 Mbps)

the link with the connected network device is established

flashing green the process of packet data transmission through LAN interface

Power solid green the device power supply is enabled, normal operation, IP

address is obtained

solid orange the device is loaded but IP address is not received via DHCP

solid red the device is loading

2.6 Reset to the default settings

In order to reset the device to factory settings, press and hold the 'F' button until «Power» indicator starts flashing.

Device will be rebooted automatically. DHCP client will be launched by default. If the address is not received via

DHCP the device will have IP address —192.168.1.10,subnet mask —255.255.255.0and User Name/Password to

access via Web interface: admin/password.

 WEP-12ac user manual

2.7 Delivery package

The delivery package includes:

•WEP-12ac wireless access point;

•Mounting kit;

•Operating manual (supplied on a CD);

•Conformity certificate;

•Technical passport.

Otros manuales para WEP-12ac

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de ELTEX

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario