ELTEC BAB 740 Manual de usuario
BAB 740
Basic Automation Board with PowerPC 740
manual
Revision 2C
Revision
Revision Changes Date / Name
1A First Edition, Valid for Hardware revision 1A 03.01.2000 AR
2A Valid for Hardware revision 3A 24.04.2001 G.M.
2B Valid for Hardware revision 3A
Valid for Software revision W-O9B7-106C
- I/O-Address-Map changed -
26.09.2001 rae
2C Disclaimer new 08.11.06 hh
DISCLAIMER
Copyright
© 2006 ELTEC Elektronik AG. The information, data, and figures in this
document including respective references have been verified and
found to be legitimate. In particular in the event of error they may,
therefore, be changed at any time without prior notice. The complete
risk inherent in the utilization of this document or in the results of its
utilization shall be with the user; to this end, ELTEC Elektronik AG shall
not accept any liability. Regardless of the applicability of respective
copyrights, no portion of this document shall be copied, forwarded or
stored in a data reception system or entered into such systems without
the express prior written consent of ELTEC Elektronik AG, regardless of
how such acts are performed and what system is used (electronic,
mechanic, photocopying, recording, etc.). All product and company
names are registered trademarks of the respective companies.
Our General Business, Delivery, Offer, and Payment Terms and
Conditions shall otherwise apply.
Federal communications commission statement
Þ This device complies with FCC Rules Part 15. Operation is subject
to the following two conditions:
Þ This device may not cause harmful interference, and
Þ This device must accept any interference received including
interference that may cause undesired operation.
Þ This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try correct the interference by
one or more of the following measures:
Þ Reorient or relocate the receiving antenna.
Þ Increase the separation between the equipment and receiver.
Þ Connect the equipment to an outlet on a circuit different from
that to which the receiver is connected.
Þ Consult the dealer or an experienced radio/TV technician for help.
Þ The us of shielded cables for connection of the monitor to the
graphics card is required to assure compliance with FCC
regulations. Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
Canadian department of communications statement
Þ This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.
Þ This class B digital apparatus complies with Canadian ICES-003
SAFETY INFORMATION
Electrical safety
Þ To prevent electrical shock hazard, disconnect the power cable
from the electrical outlet before reloading the system.
Þ When adding or removing devices to or from the system, ensure
that the power cables for the devices are unplugged before the
signal cables are connected. If possible, disconnect all power
cables from the existing system before you add device.
Þ Before connecting or removing signals cables from motherboard,
ensure that all power cables are unplugged.
Þ Make sure that your power supply is set to the correct voltage in
your area. If you are not sure about the voltage of the electrical
outlet you are using, contact your local power company.
Þ If the power supply is broken, do not try to fix it by yourself.
Contact a qualified service technician or your retailer.
Operation safety
Þ Before installing the motherboard and adding devices on it,
carefully read the manuals that came with the package.
Þ Before using the product, make sure all cables are correctly
connected and the power cables are not damaged. If you detect
any damage, contact your dealer immediately.
Þ To avoid short circuits, keep paper clips, screws, and staples away
from connectors, slots sockets and circuitry.
Þ Avoid dust, humidity, and temperature extremes. Do not place the
product in any area where it may become wet.
Þ Place the product on a stable surface.
Þ If you encounter technical problems with the product, contact a
qualified service technician or your retailer.
EMC Rules
This unit has to be installed in a shielded housing. If not installed in a
properly shielded enclosure, and used in accordance with the
instruction manual, this product may cause radio interference in which
case the user may be required to take adequate measures at his or her
own expense.
IMPROTANT INFORMATION
This product is not an end user product. It was developed and
manufactured for further processing by trained personnel.
RECYCLING
Please recycle packaging environmentally friendly:
Packaging materials are recyclable. Please do not dispose
packaging into domestic waste but recycle it.
Please recycle old or redundant devices environmentally
friendly:
Old devices contain valuable recyclable materials that should
be reutilized. Therefore please dispose old devices at collection points
which are suitable.
User's Manual Table of Contents
BAB 740
I
Table of Contents
1 Specification .................................................................... 1—1
1.1 Main Features ............................................................. 1—1
1.2 Specification Details.................................................... 1—2
1.2.1 CPU Kernel .......................................................... 1—2
1.2.2 Flash Memory....................................................... 1—2
1.2.3 PCI Devices.......................................................... 1—2
1.2.4 VMEbus Interface................................................. 1—3
1.2.5 Mechanical ........................................................... 1—3
1.2.6 I/O......................................................................... 1—3
1.2.7 Software ............................................................... 1—4
1.2.8 Compatibility......................................................... 1—4
1.2.9 Related Documents.............................................. 1—4
2 Installation........................................................................ 2—1
2.1 BAB 740 I/O ................................................................ 2—1
2.1.1 VMEbus Installation ............................................. 2—2
2.1.2 What‘s needed for Installation.............................. 2—2
2.1.3 SODIMM Installation ............................................ 2—3
2.1.4 Activity LEDs ........................................................ 2—4
Table of Contents User's Manual
BAB 740
II
3 Connector Assignments ................................................. 3—1
3.1 On-board Connectors ................................................. 3—1
3.1.1 Keyboard and Mouse Connector ......................... 3—1
3.1.2 Ethernet Connector .............................................. 3—2
3.1.3 Serial Ports 1 and 2 Connectors .......................... 3—2
3.1.4 Parallel I/O Connector.......................................... 3—3
3.1.5 VMEbus Connector P1......................................... 3—4
3.2 ADAP-200 Connectors................................................ 3—6
3.2.1 8-bit SCSI ............................................................. 3—6
3.2.2 Additional I/O........................................................ 3—7
3.3 CONV-300 Connectors ............................................... 3—8
3.4 ADAP-740 Connectors................................................ 3—9
3.4.1 Floppy Disk........................................................... 3—9
3.4.2 EIDE ................................................................... 3—10
3.4.3 COM3 and COM4 .............................................. 3—11
3.4.4 Speaker .............................................................. 3—11
3.5 PMCE-740 Connectors ............................................. 3—12
3.5.1 PMCE-740 VMEbus Connector P1.................... 3—12
3.5.2 PMCE-740 PCI Mezzanine Card Connectors.... 3—13
User's Manual Table of Contents
BAB 740
III
3.5.3 PMCE-740 PCI Mezzanine Card I/O Routing .... 3—14
3.5.4 PMCE-740 Power Connector............................. 3—15
4 Board Parameters............................................................ 4—1
4.1 Host Bus...................................................................... 4—1
4.2 VMEbus....................................................................... 4—1
4.3 PCI Local Bus ............................................................. 4—4
4.4 Network ....................................................................... 4—4
4.5 SCSI............................................................................ 4—5
4.6 Serial I/O ..................................................................... 4—5
4.7 Keyboard:.................................................................... 4—5
4.8 Mouse ......................................................................... 4—6
4.9 Parallel I/O .................................................................. 4—6
4.10 MTBF Values ............................................................ 4—6
4.11 ESD Values............................................................... 4—6
4.12 Environmental Conditions ......................................... 4—6
4.13 Maximum Operating Humidity: ................................. 4—7
4.14 Power Requirements ................................................ 4—7
5 Jumpers............................................................................ 5—1
5.1 On-board Jumpers ...................................................... 5—1
Table of Contents User's Manual
BAB 740
IV
5.1.1 User-settable Jumpers ......................................... 5—2
5.2 PMCE-740 Jumpers.................................................... 5—5
5.2.1 PMCE-740 User-settable Jumpers ...................... 5—6
6 Booting ............................................................................. 6—1
6.1 Printout of Boot Screen............................................... 6—1
6.2 Booting OS-9 .............................................................. 6—2
6.2.1 Entering Boot Parameters.................................... 6—2
6.2.2 Printout of Boot Screen ........................................ 6—2
6.2.3 Ethernet Boot Printout.......................................... 6—3
7 Appendix .......................................................................... 7—1
7.1 Description of On-board Devices ................................ 7—1
7.1.1 SMI Ticker ............................................................ 7—1
7.1.2 Enhanced Serial Communications Controller
(ESCC) ................................................................. 7—3
7.1.3 Interrupt Controller ............................................... 7—4
7.1.4 SRAM/RTC........................................................... 7—5
7.1.5 GPIO Use ............................................................. 7—6
7.1.6 Super-I/O Power-on Strappings ........................... 7—6
7.1.7 I/O Address Map .................................................. 7—7
7.1.8 Memory Address Map .......................................... 7—8
Tabla de contenidos
Otros manuales de Hardware de computadora de ELTEC
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
