Elsner Cala KNX M-T Series Guía
EN
Cala KNX M-T
Push Button with Temperature Sensor
Installation and Adjustment
Cala KNX M1-T
Item numbers 70860 (white), 70862 (black)
Cala KNX M2-T
Item numbers 70870 (white), 70872 (black)
Cala KNX M4-T
Item numbers 70880 (white), 70882 (black)
1 Contents
Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany
Cala KNX M-T push button • from application 1.0
Version: 13.09.2019 • Technical changes and errors excepted.
1. Description ........................................................................................... 3
1.0.1. Scope of delivery .......................................................................................... 4
1.1. Technical data ........................................................................................................... 4
1.1.1. Accuracy of the measurement ..................................................................... 4
2. Installation and commissioning ........................................................... 5
2.1. Installation notes ...................................................................................................... 5
2.2. Installation location .................................................................................................. 5
2.3. Device structure ........................................................................................................ 7
2.3.1. Casing ............................................................................................................ 7
2.4. Installation of the sensor ......................................................................................... 7
2.5. Notes on mounting and commissioning ................................................................ 8
3. Maintenance ......................................................................................... 8
4. Transfer protocol ................................................................................. 9
4.1. List of all communications objects ......................................................................... 9
5. Setting the parameters ...................................................................... 12
5.1. Behaviour on power failure/ restoration of power .............................................. 12
5.2. General settings ..................................................................................................... 12
5.3. Temperature measured value ............................................................................... 12
5.4. Push button ............................................................................................................. 13
5.4.1. Push button 1 / 2 / 3 / 4 ............................................................................... 14
5.4.2. Control modes for drive control ................................................................ 17
5.5. LEDs ......................................................................................................................... 18
5.6. Logic ........................................................................................................................ 19
5.6.1. AND logic 1+2 and OR logic outputs 1+2 .................................................. 20
5.6.2. OR LOGIC connection inputs ..................................................................... 22
2 Clarification of signs
This manual is amended periodically and will be brought into line with new software
releases. The change status (software version and date) can be found in the contents footer.
If you have a device with a later software version, please check
www.elsner-elektronik.de in the menu area "Service" to find out whether a more up-to-
date version of the manual is available.
Clarification of signs used in this manual
Installation, inspection, commissioning and troubleshooting of the device
must only be carried out by a competent electrician.
Safety advice.
Safety advice for working on electrical connections, components,
etc.
DANGER! ... indicates an immediately hazardous situation which will lead to
death or severe injuries if it is not avoided.
WARNING! ... indicates a potentially hazardous situation which may lead to
death or severe injuries if it is not avoided.
CAUTION! ... indicates a potentially hazardous situation which may lead to
trivial or minor injuries if it is not avoided.
ATTENTION! ... indicates a situation which may lead to damage to property if it is
not avoided.
ETS In the ETS tables, the parameter default settings are marked by
underlining.
3 Description
Cala KNX M-T push button • Version: 13.09.2019 • Technical changes and errors excepted.
1. Description
The Cala KNX M-T push button has touch-sensitive buttons, with which functions
in the KNX building bus system can be called, such as switch lights and devices, dim,
activate drives, send values, scenarios. An LED is integrated into each touch button, the
behaviour of which can be adjusted.
A temperature sensor is integrated into Cala KNX M-T. An external temperature read-
ing can be received via the bus and processed with its own data to create a total tem-
perature (mixed value).
Communication objects can be connected by AND and OR logic gates.
The device is supplemented with a frame of the switch series used in the building, and
thus fits seamlessly into the interior fittings.
Cala KNX M1-T functions:
•1Touch bus button, can be configured as switch, selector switch, dimmer,
blind (position and slats up/stop OR down/stop), shutters (up/down/stop),
awning (in/out/stop), window (closed/open/stop), as 8 or 16-bit encoder or for
scenario recall/storage
Cala KNX M2-T functions:
•2 Touch bus button, can be configured as switch, selector switch, dimmer,
for operating drives, as 8 or 16-bit encoder or for scenario recall/storage
•Area function when touching both push buttons. Can be configured as
switch, selector switch, as 8 or 16 bit encoder or for scenario recall
Cala KNX M4-T functions:
•4 Touch bus button, can be configured as switch, selector switch, dimmer,
for operating drives, as 8 or 16-bit encoder or for scenario recall/storage
•Area function when touching three or more push buttons. Can be configured
as switch, selector switch, as 8 or 16 bit encoder or for scenario recall
Function of all models:
•OneLED per touch area. On for object value = 1 / Off for object value = 0, On
after pressing button for settable time or always off. Settable, as to whether
LED flashes at block object value = 1
•Temperature measurements. Mixed value from own measured value and
external values (proportion can be set by percentage)
•2 AND and 2 OR logic gates each with 4 inputs. All switching events as well
as 8 logic inputs (in the form of communications objects) can be used as inputs
for the logic gates. The output from each gate can be configured optionally as
1-bit or 2 x 8-bit
Configuration is made using the KNX software ETS 5. The product file can be down-
loaded from the ETS online catalogue and the Elsner Elektronik website on www.els-
ner-elektronik.de in the “Service” menu.
4 Description
Cala KNX M-T push button • Version: 13.09.2019 • Technical changes and errors excepted.
1.0.1. Scope of delivery
• Push button in casing
• Base plate
Additionally required (not included in the deliverables):
• Junction box Ø 60 mm, 42 mm deep
• Frame (for insert 55 x 55 mm), compatible to the switch scheme used in the
building
1.1. Technical data
The product is compliant with the provisions of EU Directives.
1.1.1. Accuracy of the measurement
Measurement variations from permanent sources of interference (see chapter Installa-
tion position) can be corrected in the ETS in order to ensure the specified accuracy of
the sensor (offset).
Casing Genuine glass, plastic
Colours • similar to RAL 9010 pure white
• similar to RAL 9005 deep black
Installation Flush-mounted (wall installation in junction box Ø60 mm,
42 mm deep or cavity wall socket for burr hole Ø68 mm)
IP rating IP 20
Dimensions Housing approx. 55 x 55 (W x H, mm),
Installation depth approx. 10 mm,
Base plate approx. 71 x 71 (W x H, mm),
Total weight approx. 50 g
Ambient temperature Operating -25…+80°C, storage -30…+85°C
Ambient humidity max. 95% RH, avoid condensation
Operating voltage KNX bus voltage
Bus current max. 15 mA
Data output KNX +/- Bus plug-in terminal
BCU type Own microcontroller
PEI type 0
Group addresses max. 183
Allocations max. 183
Communication objects Cala KNX M1-T: 44
Cala KNX M2-T: 55
Cala KNX M4-T: 73
Temperature measurement
range
-25…+80°C
Temperature resolution 0.1°C
Temperature accuracy ± 0.5°C at 0…+50°C
(Note the information about Accuracy of the measurement)
5 Installation and commissioning
Cala KNX M-T push button • Version: 13.09.2019 • Technical changes and errors excepted.
When measuring temperature, the self-heating of the device is considered by the
electronics. The heating is compensated by the software.
2. Installation and commissioning
2.1. Installation notes
Installation, testing, operational start-up and troubleshooting should
only be performed by an electrician.
CAUTION!
Live voltage!
There are unprotected live components inside the device.
• National legal regulations are to be followed.
• Ensure that all lines to be assembled are free of voltage and take
precautions against accidental switching on.
• Do not use the device if it is damaged.
• Take the device or system out of service and secure it against
unintentional use, if it can be assumed, that risk-free operation is no
longer guaranteed.
The device is only to be used for its intended purpose. Any improper modification or
failure to follow the operating instructions voids any and all warranty and guarantee
claims.
After unpacking the device, check it immediately for possible mechanical damage. If it
has been damaged in transport, inform the supplier immediately.
The device may only be used as a fixed-site installation; that means only when assem-
bled and after conclusion of all installation and operational start-up tasks and only in
the surroundings designated for it.
Elsner Elektronik is not liable for any changes in norms and standards which may occur
after publication of these operating instructions.
2.2. Installation location
The Cala KNX M-T push button is designed for wall installation in a connector sock-
et (Ø 60 mm, 42 mm deep).
6 Installation and commissioning
Cala KNX M-T push button • Version: 13.09.2019 • Technical changes and errors excepted.
May be installed and operated in dry interior rooms only.
Avoid condensation.
When selecting an installation location, please ensure that the measurement results
are affected as little as possible by external influences. Possible sources of interference
include:
• Direct sunlight
• Drafts from windows and doors
• Draft from ducts which lead from other rooms or from the outside to the
junction box in which the sensor is mounted
• Warming or cooling of the building structure on which the sensor is mounted,
e.g. due to sunlight, heating or cold water pipes
• Connection lines and ducts which lead from warmer or colder areas to the
sensor
Measurement variations from permanent sources of interference can be corrected in
the ETS in order to ensure the specified accuracy of the sensor (offset).
Fig. 1: Sectional drawing.
The Cala KNX M-T push button fits in a standard con-
nector socket (Ø 60 mm, depth 42 mm).
The frame is not included in the delivery!
Installation depth
27 mm
Construction depth
10 mm
7 Installation and commissioning
Cala KNX M-T push button • Version: 13.09.2019 • Technical changes and errors excepted.
2.3. Device structure
2.3.1. Casing
2.4. Installation of the sensor
First install the windproof socket with feed line. Seal the inlet tubes as well, in order to
prevent draughts.
Then screw the base plate to the socket and place the switch program frame. Connect
the bus cable +/- to the plug (black-red).
Insert the device firmly onto the metal frame using the catches so that the device and
the housing are fixed together. The device has to be inserted such that the bus terminal
faces up (see Fig. 3). This is necessary for a correct temperature measurement and for
Cala KNX M2-T and Cala KNX M4-T also for button allocation.
Fig. 2: Front
1 Ventilation slit (top and bottom)
2 Touch areas with LEDs
1
1
2
2
2
2
1
1
22
Fig. 3: Back
1 Base frame
2 KNX terminal BUS +/-
3 Programming button (recessed) for
teaching the device
4 Programming LED (recessed)
5 Catches
5
1
3
2
4
8 Maintenance
Cala KNX M-T push button • Version: 13.09.2019 • Technical changes and errors excepted.
2.5. Notes on mounting and commissioning
Never expose the device to water (e.g. rain) or dust. This can damage the electronics.
You must not exceed a relative humidity of 95%. Avoid condensation.
After the bus voltage has been applied, the device will enter an initialisation phase last-
ing a few seconds. During this phase no information can be received or sent via the
bus.
3. Maintenance
Ventilation slits must not be dirty of covered. As a rule, it is sufficient to wipe the device
with a soft, dry cloth as required.
Este manual sirve para los siguientes modelos
9
Tabla de contenidos
Otros manuales de Controladores de Elsner
Elsner
Elsner Cala KNX T 201 Sunblind Guía
Elsner
Elsner KNX eTR Sunblind Series Guía
Elsner
Elsner 71200 Manual de usuario
Elsner
Elsner KNX eTR 208 Light/Sunblind Guía
Elsner
Elsner KNX eTR Sunblind Manual de usuario
Elsner
Elsner KNX S1E-UP 230V Guía
Elsner
Elsner KNX Touch One Style Guía
Elsner
Elsner Cala KNX M-T CH Series Guía
Elsner
Elsner WS1000 Color Manual del propietario
Elsner
Elsner KNX S4-B10 230 V Guía
