ELNA 6200 - Manual de usuario
1
CONDITION CAUSE HOW TO FIX REFERENCE
1. SKIPPING
STITCHES
1. NEEDLE IS NOT INSERTED
PROPERLY.
2. NEEDLE IS BENT OR WORN.
3. INCORRECTLY THREADED.
4. NEEDLE OR THREAD ARE
INAPPROPRIATE FOR
FABRIC BEING SEWN.
5. SEWING ON STRETCH
FABRIC.
6. PRESSER FOOT PRESSURE
IS TOO WEAK.
7. INAPPROPRIATE NEEDLE
BAR HEIGHT.
8. INAPPPROPRIATE NEEDLE
TO HOOK TIMING.
9. INAPPROPRIATE NEEDLE
TO HOOK CLEARANCE.
INSERT THE NEEDLE PROPERLY.
CHANGE THE NEEDLE.
RETHREAD.
USE THE RECOMMENDED
SEWING NEEDLE AND THREAD.
USE A #11 BLUE TIP NEEDLE.
ADJUST THE PRESSER BAR
LEVEL TO MAKE THE
PRESSURE STRONGER.
SEE MECHANICAL ADJUSTMENT
“NEEDLE BAR HEIGHT”.
SEE MECHANICAL ADJUSTMENT
“NEEDLE TO HOOK TIMING”.
SEE MECHANICAL ADJUSTMENT
“CLEARANCE BETWEEN NEEDLE
AND HOOK”.
P. 1 3
P. 1 2
P. 1 4
2. FABRIC NOT
MOVING
1. PRESSER FOOT PRESSURE
IS TOO WEAK.
2. INCORRECT F.D. HEIGHT.
3.F.D. IS IN DOWN POSITION.
4.THREAD ON BOTTOM SIDE
OF FABRIC IS JAMMED UP.
5. FEED DOG TEETH ARE WORN.
ADJUST THE PRESSER BAR
LEVEL TO MAKE THE
PRESSURE STRONGER.
SEE MECHANICAL
ADJUSTMENT “FEED DOG HEIGHT”.
RAISE THE F.D. LEVEL.
MAKE SURE TO BRING BOTH
NEEDLE AND BOBBIN.
THREAD UNDER THE FOOT WHEN
STARTING SEWING.
CHANGE THE FEED DOG.
P. 1 6
WHAT TO DO WHEN
2
CONDITION CAUSE HOW TO FIX REFERENCE
3. BREAKING
UPPER
THREAD
1. INITIAL SEWING SPEED IS
TOO FAST.
2. THREAD PATH IS INCORRECT.
3. NEEDLE IS BENT OR DULL.
4. UPPER THREAD TENSION IS
TOO STRONG.
5. NEEDLE SIZE IS
INAPPROPRIATE FOR FABRIC.
6. NEEDLE EYE IS WORN.
7. NEEDLE HOLE IN NEEDLE
PLATE IS WORN OR BURRED.
START WITH MEDIUM SPEED.
USE THE PROPER THREAD PATH.
REPLACE WITH A NEW NEEDLE.
ADJUST NEEDLE THREAD TENSION
CORRECTLY.
USE APPROPRIATE NEEDLE FOR
FABRIC AND THREAD IN USE.
CHANGE THE NEEDLE.
REPAIR THE HOLE OR REPLACE
THE NEEDLE PLATE.
P. 1 8
4. BREAKING
BOBBIN
THREAD
1. INCORRECITLY THREADED
BOBBIN.
2. TOO MUCH THREAD IS
AROUND ON THE BOBBIN.
3. LINT IS STUCK INSIDE THE
BOBBIN HOLDER.
4. THREAD QUALITY IS
TOO LOW.
5. THREAD IS JAMMING
AROUND THE BOBBIN.
THREAD BOBBIN CORRECTLY.
ADJUST THE POSITION OF STOPPER.
CLEAN THE SHUTTLE.
CHANGE TO A HIGH QUALITY
SEWING THREAD.
CLEAR OUT THE JAMMING THREAD.
5. NEEDLE
BREAKS
1. NEEDLE IS HITTING THE
NEEDLE PLATE.
2. NEEDLE IS BENT OR WORN.
3. NEEDLE IS HITTING THE
HOOK.
4. THE FABRIC MOVES WHILE
THE NEEDLE IS PIERCING
IT, OR THE NEEDLE ZIGZAGS
WHILE IN FABRIC.
5. FABIRIC IS BEING PULLED TOO
STRONGLY WHILE SEWING.
SEE MECHANICAL
ADJUSTMENT “NEEDLE POSITION”.
CHANGE THE NEEDLE.
SEE MECHANICAL ADJUSTMENT
“CLEARANCE BETWEEN NEEDLE
AND HOOK”.
SEE MECHANICAL ADJUSTMENT
“ZIGZAG SYNCHRONIZATION”.
GUIDE THE FABRIC GENTLY
WHILE SEWING.
P. 1 1
P. 1 4
P. 1 7
3
CONDITION CAUSE HOW TO FIX REFERENCE
6. NOISY
OPERATION
1. BACKLASH BETWEEN HOOK
GEAR AND LOWER
SHAFT GEAR IS TOO GREAT.
2. LOWER SHAFT GEAR IS
LOOSE.
3. INAPPROPRIATTE BELT
TENSION.
4. NOT ENOUGH OIL.
SEE MECHANICAL ADJUSTMENT
“BACKLASH (LOWER SHAFT GEAR)”.
ELIMINATE THE LOOSENESS.
SEE PART REMOVAL AND
REPLACEMENT “DRIVING MOTOR
(DC MOTOR)”.
OIL ALL MOVING PARTS.
P. 1 5
P. 2 7
P. 3 6
7. DEFORMATION
PATTERN
1. INAPPROPRIATE FEED
BALANCE.
2. INAPPROPRIATE ZIGZAG
SYNCHRONIZATION.
3. UPPER THREAD TENSION
IS TOO STRONG.
SEE MECHANICAL ADJUSTMENT
“STRETCH STITCH FEED BALANCE”.
SEE MECHANICAL ADJUSTMENT
“ZIGZAG SYNCHRONIZATION”.
SEE MECHANICAL ADJUSTMENT
“NEEDLE THREAD TENSION”.
P. 1 9
P. 1 7
P. 1 8
4
SERVICE ACCESS (1)
FACE COVER (UNIT)
TO REMOVE:
REMOVE THE CAP AND SETSCREW.
REMOVE THE FACE COVER
TO ATTACH:
FOLLOW THE PROCEDURE ABOVE IN REVERSE.
SETSCREW
CAP
FACE COVER
5
SERVICE ACCESS (2)
SETSCREW (A)
CARRYING HANDLE
SETSCREW
TOP COVER (UNIT)
TO REMOVE:
RAISE THE CARRYING HANDLE AND REMOVE THE SETSCREW (A).
OPEN THE TOP COVER AND REMOVE THE SETSCREW (B).
LIFT UP THE TOP COVER AND REMOVE IT FROM THE REAR SIDE.
TO ATTACH:
FOLLOW THE PROCEDURE ABOVE IN REVERSE.
6
REPLACING THE BELT COVER
TO REMOVE:
1. RAISE THE CARRYING HANDLE AND LOOSEN THE SCREW (A).
2. REMOVE THE CAP AND THE SCREW (B).
3. LOOSEN THE SCREW (C) AND THE BELT COVER.
TO ATTACH:
FOLLOW THE PROCEDURE IN REVERSE.
SERVICE ACCESS (3)
SETSCREW (A)
CARRYING
HANDLE SETSCREW
(B)
SETSCREW (C)
CAP
7
SERVICE ACCESS (4)
REPLACING THE BED COVER (UNIT)
TO REMOVE:
PUSH THE DROP FEED DOG LEVER TO THE LEFT. REMOVE THE SETSCREWS (A), THEN REMOVE
THE BED COVER (UNIT).
TO ATTACH:
PUSH THE DROP FEED DOG LEVER TO THE LEFT. ATTACH THE BED COVER (UNIT) AND TIGHTEN
THE SETSCREWS (A).
REPLACING THE BASE
TO REMOVE:
REMOVE THE SETSCREWS (A), (B), (C), (D) AND (E).
REMOVE THE BASE.
TO ATTACH:
FOLLOW THE PROCEDURE IN REVERSE.
SETSCREW (B)
SETSCREWS (A)
DROP FEED DOG
LEVER
BED COVER (UNIT)
SETSCREW (C)
SETSCREW (A)
SETSCREW (D)
SETSCREW (E)
BASE
8
SERVICE ACCESS (5)
REPLACING THE FRONT COVER (UNIT)
TO REMOVE:
REMOVE THE FACE COVER (UNIT), TOP COVER (UNIT) AND BELT COVER. (SEE PAGE 4, 5, 6)
LOOSEN THE SETSCREWS (A), (B) AND (C). THEN REMOVE THE FRONT COVER (UNIT). DISCONNECT
THE CONNECTOR FOR PRINTED CIRCUIT BOARD-F AND FLEXIBLE FLAT CABLE FROM THE PRINTED
BOARD-A.
NOTE:
NEVER PULL ON CORD WHEN DISCONNECT THE CABLES FROM THE CIRCUIT BOARD.
TO ATTACH:
FOLLOW THE PROCEDURE IN REVERSE.
SETSCREW (C)
SETSCREW (B)
SETSCREW (A)
FRONT COVER
SETSCREW (A)
SETSCREW (B)
SETSCREW (C)
FLEXIBLE FLAT CABLE
CONNECTOR FOR
BOBBIN WINDING
SWITCH
9
SERVICE ACCESS (6)
REPLACING THE REAR COVER
TO REMOVE:
REMOVE THE FACE COVER (UNIT), TOP COVER (UNIT) AND BELT COVER. (SEE PAGE 4, 5, 6)
LOOSEN THE SETSCREWS (A), (B), (C) AND (D), THEN REMOVE THE CAP AND SETSCREW (F). LOWER
THE PRESSER FOOT LIFTER AND REMOVE THE REAR COVER FROM THE PRESSER FOOT LIFTER
SECTION FIRST.
TO ATTACH:
FOLLOW THE PROCEDURE ABOVE IN REVERSE..
SETSCREW (A)
SETSCREW (B)
PRESSER FOOT
LIFTER
SETSCREW (E)
CAP
SETSCREW (C)
SETSCREW (D)
Otros manuales para 6200 -
2
Tabla de contenidos
Otros manuales de Máquina de coser de ELNA
ELNA
ELNA 2002 Manual de usuario
ELNA
ELNA Elinita EF72 Manual de usuario
ELNA
ELNA EnVision 8006 Manual de usuario
ELNA
ELNA Sew Fun Manual de usuario
ELNA
ELNA eXtend 864air Manual de usuario
ELNA
ELNA Cover Pro 2000CPX Guía de solución de problemas
ELNA
ELNA 744 Manual de usuario
ELNA
ELNA Elnita ec60 Manual de usuario
ELNA
ELNA 6005 heirloom edition Manual de usuario
ELNA
ELNA 5300 - Manual de usuario
ELNA
ELNA eXperience 620 Manual de usuario
ELNA
ELNA 3210 Manual de usuario
ELNA
ELNA EnVision 8006 Manual de usuario
ELNA
ELNA 845 - Diagrama de cableado
ELNA
ELNA TSP AIR ELECTRONIC Manual de usuario
ELNA
ELNA 9500 - LEAFLET Manual de usuario
ELNA
ELNA eXpressive 970 Manual de usuario
ELNA
ELNA 5100 - Manual de usuario
ELNA
ELNA Elnita Manual de usuario
ELNA
ELNA Xquisit II Manual de usuario
