Elmdene LPS-12-G2 Manual de instrucciones

LPS-12-G2 / LPS-12-G3 Installation & User Manual

INTRODUCTION

This manual covers the Grade 2 and Grade 3 variants of the Li-Power Intruder approved

product. This power supply unit has been designed to house common alarm

communicators providing compliant, reliable power to the

chosen device.

Provided with a Lithium battery pack it ensures the device

remains powered in the event of a mains failure. The

Integrated Intelligent Battery Management features

provide active battery testing, low battery voltage

detection and deep discharge protection to ensure that the

battery is kept in optimal condition. It also has a range of

comprehensive self-diagnostics, including thermal cut-off

protection.

EN50131-6 approved product. Contains Li-ion batteries

FEATURES

•Provides continuous current to load for systems requiring 12Hrs (Grade 2) or 30Hrs

(Grade 3) standby from the supplied battery pack as specified in EN50131.

•Flame retardant (UL94 V0) hinged enclosure with screw lock lid.

•Front / rear tamper detection.

•Can be securely wall mounted.

•Cable ingress/egress management facilitated via breakout features on three sides as

well as pilot drill points located around the periphery of the enclosure.

•Independent output signals indicate loss of AC power, battery and power supply fault.

•Inbuilt charger and monitoring circuits ensures safe battery operation.

•Intelligent battery management comprises active load battery testing, low battery

voltage detection and deep discharge protection to ensure that the battery is not

permanently damaged through excessive discharge.

•Comprehensive self-diagnostics with internal LED status indications

•Product includes AC power transient filtering, electronic output overload protection

and fuses for the load and battery outputs.

Refer to the enclosed Safety Sheet before installation and first use.

SAFETY INFORMATION

Once installed and commissioned no further involvement is required for normal

operation. Under normal conditions with AC mains applied, the power supply will provide

a continuous load current of up to 150mA whilst the intelligent battery management

automatically charges, tests and maintains the installed battery pack. Should a fault

occur, the relevant fault signal will be activated, and in-built diagnostic LEDs will provide

additional information regarding the type of fault detected. The unit will continue normal

operation once the fault has been rectified.

Should a loss of mains occur, the unit will flag a fault and seamlessly switch to the battery

pack for power, with the unit capable of running for up to 30hrs (dependent on load and

battery pack installed). Should the battery pack become depleted before mains power is

re-applied the Alternative Power Supply (APS) fault will be flagged to indicate battery

power is very low, occurring a few minutes (dependent on load, battery pack and other

conditions) prior to the battery pack disconnecting and all power to the load being

dropped.

Once mains power has been restored, power to the load from the power supply will

automatically be provided and the battery pack will start to be recharged as required

(subject to environmental conditions).

For monitoring, three independent output signals are provided to indicate, loss of AC

power fault (EPS), battery fault (APS), and power supply fault (GEN).

Comprehensive self-diagnostics give detection of:

•blown output fuse

•battery disconnection

•battery fault

•low battery voltage

•low output voltage

•battery charger only operational between 3°C and 50°C

Monitoring functions are described in the Signalling Outputs section.

Comprehensive protection is built-in as standard to include:

•AC power transient filtering

•electronic output overload protection

•fuses on the load and battery outputs

•deep discharge protection

•brownout filter to prevent false loss of AC power fault (10 seconds)

OPERATION AND MONITORING OVERVIEW

INSTALLATION AND COMMISSIONING

This unit is only suitable for installation as permanently connected equipment and is to

be used with DC appliances only. This equipment is NOT SUITABLE for external

installation and must be installed according to all relevant safety regulations.

Figure 1: PSU internal components

The unit must be fed from an AC power source having a separate (approved) disconnect

device and fitted with a fuse or other over-current protection device rated at 3A

maximum. Ensure that the disconnect device used has appropriate earth fault protection

to the applicable standard.

1) Mounting

a) Remove battery and bungee. Mount securely at 3 positions allowing minimum

clearance of 10cm from walls, ceilings or other obstacles.

b) Route power and LV cables via different knockouts / cable entry holes.

c) Use bushes and cable glands rated to UL94 HB minimum.

2) AC Power Up (commissioning)

a) Attach correctly rated AC power cable and fasten using cable ties.

b) Apply AC power. Check for 12Vdc on load outputs and AC power LED is on.

c) Disconnect AC power.

3) Load Output (commissioning)

a) Fit battery in compartment using self-adhesive tape and bungee provided.

b) Attach supplied battery to the connector B1 (BATT).

NOTE: ensure correct polarity of battery connections.

c) Apply AC power. Check AC power LED is on.

d) Check there is no fault indication on the Fault LED. A single short flash indicates the

battery is charging, please note, this is normal operation.

e) Disconnect AC power. Check that the battery continues to supply voltage and

current to the load.

f) Reconnect AC power.

4) Tamper

a) Connect tamper switch to Control & Indicating Equipment (CIE) inputs.

b) Check that the CIE recognises the tamper is ‘OPEN’.

c) Close the lid and check that the CIE recognises the tamper is ‘CLOSED’.

CONNECTIONS

Figure 2 shows product connections.

+, − Connections for equipment to be powered (Observe polarity).

BATT Connection to the battery pack.

APS FAULT Relay output for battery fail. Open if battery fail or open for low output

or temperature fault - Normally Closed when Healthy.

EPS FAULT Relay output for AC power fail. Open if loss of AC power - Normally

Closed when Healthy.

GEN FAULT Relay output for General Fault. Open in fault condition - Normally

Closed when Healthy.

TAMPER Front & Rear Enclosure Tamper signal –Normally Closed when Healthy.

Figure 2

In the event of loss of AC power, a battery fault or a PSU fault, the corresponding fault

signal contacts will open.

If the PTC output fuse is triggered it will automatically reset once the defect is removed.

SIGNALLING OUTPUTS

Rating 100mA @ 60Vdc 16Ω solid state relay contacts, volt-free.

EPS Fault Open if Loss of AC power for > 10s

APS Fault Open if:

Battery terminal voltage < 3Vdc (with AC Power off), or

active battery monitoring detects a failed battery, or

battery temperature is out of limits (<3°C or >50°C)

GEN Fault Open if:

Output voltage < 9.8Vdc, or Output short circuit, or

Output fuse blown

TAMPER 0.5 A @ 30Vdc volt-free contact.

Open if cover is opened, or if unit is prised from the wall.

BATTERY MANAGEMENT

Warning: risk of explosion if incorrect battery type fitted.

You must replace with the exact same battery

(Refer to Specification Section)

Maximum Battery Size 1 x 18Ah 3.6Vdc Li-Ion battery pack (supplied)

Intelligent Battery Recharge Time < 24 hours to 80%

If battery fails to charge in 24 hrs a self-test fault is

reported (Fault 1 condition)

Minimum Energy Level: 100% of rated battery capacity available when fully

charged

Protection Reverse battery connection protection

Deep Discharge Protection Battery disconnects when < 2.5Vdc battery terminal

ON-BOARD DIAGNOSTICS

Green LED

(AC power)

Red LED

(Fault/Diagnostics)

Status

OFF

Normal. Battery fully charged

One short flash

Normal. Battery charging

Two short flashes

Fault 1. Battery self-test (load test) fail. APS open.

Three short flashes

Fault 2. No Battery/battery fuse failed. APS open.

50:50 fast flash

Fault 3. Charger fault. GEN open.

50:50 slow flash

Fault 4. Low Output/fuse blown. GEN open.

Four short flashes

Fault 5. Battery < 3°C or > 50°C. Charger turned

off. APS open.

OFF

Fault 6. No AC power. No output. Battery

disconnected or fully discharged. All relays open.

OFF

One short flash

Normal. Standby Mode. Battery present, healthy

and supplying load. EPS open.

OFF

Two short flashes

Normal. Standby Mode. Battery present, healthy

and supplying load but battery low. APS relay

open.

SPECIFICATION

EN50131-6:2017 Type A PSU

EN50131-1 Environmental Class I

Grade 2 supported with 8500mAH battery pack

Grade 3 supported with 18000mAH battery pack (when EPS is sent to an ARC)

Input

Rated Voltage/Operational Voltage

90-265Vac (at 50-60Hz)

Max. AC power Input Current (at 90Vac)

Mains input fuse

T2A - Non replaceable

Class II Double insulated

Output

Voltage

9.8-13.0Vdc (12Vdc nominal)

Output Load Current (continuous)

150mA

Overvoltage Protection

Trips at 125% of rated O/P voltage

Battery Hold-up Time

G2-8500mAh-12hrs

(Batt P/N: LPS-BATT-G2)

G3-18000mAh-30hrs

(Batt P/N: LPS-BATT-G3)

Load output fuse

0.3A PTC resettable fuse

Ripple

< 150mVdc pk –pk max

Environmental

Temperature - Operating

+5°C to +40°C 90% RH non-Condensing

Temperature - Storage

-20°C to +55°C

Dimensions

260mm wide, 201mm high, 67mm deep

Weight

1.0kg max with G3 battery.

0.9kg max with G2 battery.

For Indoor Use Only

MAINTENANCE

This unit is intended for use by Service Personnel only. There are NO USER SERVICEABLE

parts, and no regular is maintenance required of the PSE other than periodic testing and

replacement of the standby battery.

END OF LIFE DISPOSAL

This product falls within the scope of EU Directives 2012/19/EU Waste Electrical and

Electronic Equipment (WEEE) and 2013/56/EU (Battery). At the end of life, the product

must be separated from the domestic waste stream and disposed via an appropriate

approved WEEE disposal route in accordance with all national and local regulations.

Before disposal of the product, any battery must be removed and disposed of separately

via an appropriate approved battery disposal route in accordance with all national and

local regulations. Package used batteries safely for onward transport to your supplier,

collection point or disposal facility.

See Specification for battery type information.

For more information see: www.recyclethis.info

The packaging supplied with this product may be recycled.

Please dispose of packaging accordingly.

COMPLIANCE

See web site for current Declaration of Conformity.

SYMBOL DEFINITIONS

SUPPORT

Elmdene International Ltd

3 Keel Close, Interchange Park,

Portsmouth, Hampshire, PO3 5QD, UK

Email: technical.support@elmdene.co.uk

Tel: +44(0)23 9269 6638

Web: www.elmdene.co.uk

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de Elmdene

Elmdene

Elmdene G1380 BMU-y Series Manual de usuario

Elmdene

Elmdene LPS-ENC-T Manual de instrucciones

Elmdene

Elmdene UNIVERSAL-12V-5A-M Manual de usuario

Elmdene

Elmdene VRS124000-P Series Manual de usuario

Elmdene

Elmdene G1380xBM Series Manual de usuario

Elmdene

Elmdene 2405ST Series Manual de usuario

Elmdene

Elmdene STX2410-H Manual de usuario

Elmdene

Elmdene G240 BM Series Manual de usuario

Elmdene

Elmdene STX2402 Series Manual de usuario

Elmdene

Elmdene 2402STE Manual de usuario

Elmdene

Elmdene G240 N Series Manual de usuario

Elmdene

Elmdene G1380xN-y-s Series Manual de usuario

Elmdene

Elmdene G1380 BMU Series Manual de usuario

Elmdene

Elmdene 2401ST Manual de usuario

Elmdene

Elmdene 20182423N Manual de usuario

Elmdene

Elmdene 2405ST Series Manual de usuario

Elmdene

Elmdene STX2405-E Manual de usuario

Elmdene

Elmdene STX2401-C Manual de usuario

Elmdene

Elmdene STX2405-MOD Manual de usuario

Elmdene

Elmdene STX2401-MOD Manual de usuario

Elmdene

Elmdene GEN2-08 Series Manual de usuario

Elmdene

Elmdene G2410BM-E Manual de usuario

Elmdene

Elmdene TR2 Manual de usuario

Elmdene

Elmdene STX2410-MOD Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario