Elmdene UNIVERSAL-12V-5A-M Manual de usuario

Elmdene International Ltd

Tel:+44 (0)23 9269 6638

3 Keel Close, Interchange Park

Fax: +44 (0)23 9266 0483

Portsmouth, Hampshire, PO3 5QD, UK

Web: www.elmdene.co.uk

Universal PSU Range

Models : UNIVERSAL-12V-5A-M

UNIVERSAL-12V-5A-L

UNIVERSAL-24V-3A-M

UNIVERSAL-1224-L

INTRODUCTION

This manual covers a range of Power Supplies and enclosures designed for use for use in Access Control

and General Security applications. Each version comprises a 13.8Vdc or 27.6Vdc high efficiency,

switched mode Power Supply designed to fit into a robust metal enclosure. It has a unique universal

mounting system to allow fitment of a variety of 3rd party controllers or electronic devices. The Power

Supplies provide continuous full rated current to load plus an additional 0.5A battery charging for standby

lead acid batteries. Normal operation and fault signal outputs are provided.

FEATURES

•Continuous full rated current to load.

•Universal mains input rated voltage ranging from 100Vac to 240Vac.

•12Vdc, 24Vdc and selectable 12Vdc / 24Vdc options.

•High efficiency electronics for reduced running costs and lower operating temperatures.

•Installer safe design with all high voltage electronics fully protected.

•Full electronic short circuit and overload protection on load output under mains operation.

•Mains transient protection circuit.

•Front and rear tamper detection.

•Mains present LED.

•LED Fault indication.

•Universal mounting means for 3rd party Control Modules.

•Individually fused output(s).

•Deep discharge protection helps prevent battery failure when operating in standby mode for

extended periods.

SAFETY

Refer to the Power Supply Equipment (PSE) instruction for safe use.

Customer Support: +44(0)23 9269 6638

PAK200972_01A

Page 2 of 8

Large enclosure: 5 fixing positions

Medium enclosure: 3 fixing positions

This unit is intended for use by trained Service Personnel only. Once installed and operational there

are no user functions other than observance of the two LED indicators.

The green Mains LED will be illuminated whilst the mains supply is present. In the event of a fault

condition, the lower Fault LED will be illuminated under the conditions shown on page 7.

INSTALLATION AND COMMISSIONING

Installation and repair must be carried out by a certified professional or qualified electrician in

accordance with all relevant safety regulations that are applicable.

This unit is only suitable for installation as permanently connected equipment. This PSU is NOT

SUITABLE for external installation. This unit must be fed from a mains power source having a separate

(approved) disconnect device and fitted with a fuse or other over-current protection device rated at

3A maximum. Ensure that the disconnect device used has appropriate earth fault protection to the

applicable standard and before installation, ensure that external disconnect device is OFF.

EQUIPMENT MUST BE EARTHED.

OPERATING INSTRUCTIONS

Customer Support: +44(0)23 9269 6638

PAK200972_01A

Page 3 of 8

1. Mounting

•Mount enclosure securely in the orientation shown on Page 2 using 5mm diameter x

25mm minimum long screws that are appropriate for the mounting material.

•Allow minimum clearance of 100mm between the enclosure sides and ceilings or adjacent

walls. The enclosure must be mounted on a solid and continuous surface (e.g.: a wall, not

a column).

2. Cabling

•Route mains and low voltage/signal cables via separate cable entry holes.

•Use bushes and cable glands rated to the required standard.

3. Mains Power Up

•Attach correctly rated mains cable (minimum 0.5mm2[3A], 300/500Vac) and fasten using

cable ties.

•In the case of the 12/24Vdc switchable Power Supply, check that the correct output

voltage is selected.

•Apply mains power. Check for the correct output voltage on load outputs.

•Check green Main LED is on.

•Disconnect mains power.

4. Load Output

+LOAD

Red +ve voltage O/P to load equipment

-LOAD

Black -ve voltage O/P to load equipment

+BATT

Red lead to standby battery

-BATT

Black lead to standby battery

Tamper x 2

Tamper volt free contact

EPS

Volt free contacts for loss of mains indication

GEN

Volt free contacts for general faults (see signalling

outputs)

•Attach correctly rated load cable and fasten using cable ties. Check polarity

•Apply mains power and check green mains LED is on.

NOTE: Fault LED may be lit to indicate that no battery has been connected. This is normal.

•Verify load is operating correctly.

•Disconnect mains power.

Customer Support: +44(0)23 9269 6638

PAK200972_01A

Page 4 of 8

+ve (red) cable from

PSU

-ve (black) cable from

PSU

Link cable

+ve battery terminal

-ve battery terminal

Note: Battery

orientations may be

reversed. Observe

polarity.

5. Standby battery

NOTE: Ensure batteries being fitted to the unit are in good condition.

•Attach supplied battery cables to terminal block and then the battery.

NOTE: Ensure correct polarity of connections: +ve = red lead, -ve = black lead.

•For 24V systems with two batteries, connect as diagram below.

•Apply mains power and check green Mains LED is on.

•Check the fault indication LED is not illuminated.

•Disconnect mains power. Check that the batteries continue to supply voltage and current

to the load. The Green LED should be off.

NOTE: Batteries must have sufficient charge to supply the attached load.

•Reconnect mains power. Green LED should be on.

•Disconnect mains power, remove load fuse and check Fault LED is on.

•Replace Load fuse. Reconnect mains power, check Fault LED is off.

6. Tamper

•Connect tamper switch to the inputs of the control and indicating equipment (CIE).

•Close the lid and secure with the screw provided.

•With the unit mounted on the wall, check that the rear tamper is not over a recess or

raised area that will adversely affect its operation (e.g., over a mortar course).

•Check that the tamper switch is:

CLOSED when the cover is closed and the lid retaining screws are fitted.

OPEN when the retaining screws are removed.

•Use the adjustment screw if necessary to ensure the tamper switch operates when the lid

opens and closes.

•Close and fasten the cover. Re-check the tamper circuit is closed at the control panel.

Lid fixing screw

(Sets Tamper switch)

Tamper switch

connections

Adjustment screw

Customer Support: +44(0)23 9269 6638

PAK200972_01A

Page 5 of 8

CONNECTIONS,ALL SKUS

+LOAD

Red +ve voltage O/P to load equipment

-LOAD

Black -ve voltage O/P to load equipment

+BATT

Red lead to standby battery

-BATT

Black lead to standby battery

Tamper x 2

Tamper volt free contact

EPS

Volt free contacts for loss of mains indication

GEN

Volt free contacts for general faults (see signalling

outputs)

3RD PARTY CONTROLLERS

The hole pattern in the enclosures allows a wide variety of 3rd-party controllers to be mounted in any

position. A fixing kit is included that comprises different sizes of standoffs and self-tapping screws

for this purpose.

For PCB type controllers, use arrowhead type standoffs:

For controllers that are mounted using screws:

2. Align controller in

suitable position in

enclosure.

1. Fit standoffs into

suitable PCB mounting

holes. Ensure correctly

sized standoffs (3mm

or 4mm) are selected.

3. Press standoffs into

selected hole position.

1. Align controller in

suitable position in

enclosure.

2. Fasten screws (Max torque 0.6Nm.)

Screw types supplied:

No 8 x 3/8” long

M4 x 25mm long Taptite

Customer Support: +44(0)23 9269 6638

PAK200972_01A

Page 6 of 8

CONFIGURATIONS

Top Level part numbers for each available configuration are tabled below.

Enclosure: L: Large, M: Medium. See Specification section for dimensions.

SPECIFICATION

Model

UNIVERSAL-

12V-5A-x

UNIVERSAL-

1224-x

(12Vdc)**

UNIVERSAL-

24V- 3A-x

UNIVERSAL-

1224-x

(24Vdc)

Input Specification

Voltage (Rated)

120Vac –240Vac

100Vac –240Vac

Voltage

(Operating)

90Vac-264Vac

Frequency

50 –60 Hz

Max input current

at 90Vac

Output Specification

Mains Voltage

(Vdc)

13.5V to 14.2V

13.5V to 14.0V

27.0V to 28V nominal dc voltage

Standby battery

Voltage (Vdc)

10V to 12.3V

10V to 12.4V

21.0V to 24.7V

Ripple (peak to

peak Vdc)

<150mV

Max load current

Fuses

Mains input fuse

T3.15A HRC

Output fuse

4 x F1.25A

F8A

4 x F0.8A

F4A

Battery fuse

F5A

N/Applicable

F3.15A

None

PSU protect

N/Applicable

F4A

N/Applicable

F4A

** Default factory setting for the 1224 Power Module is 12Vdc mode

SKU

Enclosure

Description

UNIVERSAL-12V-5A-M

12V 5A Monitored in Medium enclosure

UNIVERSAL-12V-5A-L

12V 5A Monitored in Large enclosure

UNIVERSAL-24V-3A-M

24V 3A Monitored in Medium enclosure

UNIVERSAL-24V-5A-L

24V 5A Monitored in Large enclosure

UNIVERSAL-1224-L

12v 8A / 24V 4A selectable in Large enclosure

Customer Support: +44(0)23 9269 6638

PAK200972_01A

Page 7 of 8

Standby battery

Battery type

Valve regulated sealed lead acid

Voltage

12Vdc

24V (12Vdc x 2)

Maximum battery size

Medium enclosure: 2 x 17Ah or 3 x 7 Ah

Large enclosure: 2 x 17Ah or 4 x 7Ah

Battery charge current

Up to 0.5A

Mechanical

M (Medium) Enclosure

L (Large) Enclosure

Dimensions

(Including lid and

mounting tabs)

Width: 382mm

Height: 337mm

Depth: 90mm

Width: 407mm

Height: 507mm

Depth: 90mm

Weight

(Excluding batteries and

controllers)

~3.3kg

~5.2kg

Environmental

Temperature (Operating)

-10°C to 40°C RH75%

Temperature (Storage)

-20°C to 80°C

INDICATIONS AND FAULTS

EPS Fault [Mains Fault]

0.1A @ 60Vdc Normally Open volt free contact.

Open when loss of mains detected.

GEN Fault [General Fault]

0.1A @ 60Vdc Normally Open volt free contact

Open with general fault condition.

TAMP [front and rear] tamper]

Normally Open volt free contact

‘Open’when lid opened, or unit removed from wall.

Local Indicators (LEDs)

Mains Present LED

Green=Mains Present; Off=Mains Missing

Fault LED

Flashing = Fault detected; Off = Operating normally

Customer Support: +44(0)23 9269 6638

PAK200972_01A

Page 8 of 8

MAINTENANCE

There is no regular maintenance required of the PSU other than periodic testing and replacement of

the standby battery. Reference should be made to the battery manufacturer’s documentation to

determine typical/expected battery life with a view to periodic replacement of the battery.

If the output of the PSU fails, the cause of the failure should be investigated e.g., short circuit load. The

fault should be rectified before restoring power to the PSU. If a fuse needs to be replaced, ensure the

correct rating and type is used.

END OF LIFE

This product falls within the scope of EU Directives 2012/19/EU Waste Electrical and Electronic

Equipment (WEEE) and 2013/56/EU (Battery). At the end of life, the product must be separated from

the domestic waste stream and disposed via an appropriate approved WEEE disposal route in

accordance with all national and local regulations.

Before disposal of the product, any battery must be removed and disposed of separately via an

appropriate approved battery disposal route in accordance with all national and local regulations.

Package used batteries safely for onward transport to your supplier, collection point or disposal facility.

See Specification for battery type information.

For more information see: www.recyclethis.info.

The packaging supplied with this product may be recycled.

COMPLIANCE

See Elmdene International web site for current Declaration of Conformity.

SYMBOLS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de Elmdene

Elmdene

Elmdene GEN2-08 Series Manual de usuario

Elmdene

Elmdene STX2401-MOD Manual de usuario

Elmdene

Elmdene G1380xBM Series Manual de usuario

Elmdene

Elmdene STX2410-MOD Manual de usuario

Elmdene

Elmdene 2405ST Series Manual de usuario

Elmdene

Elmdene 2405ST Series Manual de usuario

Elmdene

Elmdene STX2405-MOD Manual de usuario

Elmdene

Elmdene G240 BM Series Manual de usuario

Elmdene

Elmdene G1380xN-y-s Series Manual de usuario

Elmdene

Elmdene 2401ST Manual de usuario

Elmdene

Elmdene G1380 BMU-y Series Manual de usuario

Elmdene

Elmdene G2410BMU Manual de usuario

Elmdene

Elmdene STX2410-H Manual de usuario

Elmdene

Elmdene G2410BM-E Manual de usuario

Elmdene

Elmdene 2401ST Manual de usuario

Elmdene

Elmdene STX2402 Series Manual de usuario

Elmdene

Elmdene VRS124000-P Series Manual de usuario

Elmdene

Elmdene G13804NU Manual de usuario

Elmdene

Elmdene POE1230-C Manual de usuario

Elmdene

Elmdene G240 N Series Manual de usuario

Elmdene

Elmdene STX2405-E Manual de usuario

Elmdene

Elmdene 20182423N Manual de usuario

Elmdene

Elmdene LPS-ENC-T Manual de instrucciones

Elmdene

Elmdene G1380 BMU Series Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario