Elite Screens CineTension 2 Series Manual de usuario

Rev.102111-AS

www.elitescreens.com [email protected]

Tab-tensioned Electric Motorized Projection Screen

CineTension 2 Series

User’s Guide

Rev.102111-AS

www.elitescreens.com [email protected]

Make sure to read this user’s guide and follow the procedure below.

•Please retain this user’s guide for future reference.

•To avoid damaging the unit, do not use with any unauthorized accessories not

recommended by the manufacturer.

•Handle the unit carefully during transportation to avoid any damages.

•To ensure safe and reliable operation, direct connection to a properly grounded power

source is advised.

•The power outlet supplying power to the unit should be close to the unit and easily

accessible.

•Do not install the unit on uneven or inclined surfaces.

•Do not place any heavy objects over the power cord.

•Position the power cord properly to avoid creating a trip obstacle.

•To avoid an electrical shoc or fire, due to a loose contact or short circuit, do not

overload the power cord.

•The internal & external parts of this unit are not end user serviceable. Do not attempt to

disassemble this unit by yourself. No one except authorized technicians can open and

ma e repairs to this unit.

•Ma e sure the power source that this unit is connected to has a continuous power flow.

•If there is need to use an extension cord, ma e sure the cord has an equal rating as the

appliance to avoid over heat.

•Do not handle the power plug when your hands are wet or your feet are in contact with

water.

Do not use this unit under the following circumstances.

•Disconnect the power cord under the conditions of heavy rain, wind thunder or

lightning.

•Avoid direct sun light, rain shower and moisture.

•Keep away from fire sources and high temperature to prevent this device from

overheating.

•Cut off the power supply first before transportation or maintenance.

•To avoid possible injury and/or an electric shoc , do not attempt to use this screen if

there is obvious damage or if there are any evident bro en parts.

Important Safety & Warning Precautions

Rev.102111-AS

www.elitescreens.com [email protected]

Due to various installation environments, the instructions provided in this user’s guide are for

reference only. Please consult a professional installation company for further installation and

safety advice. The installer must insure that proper mounting hardware is used to provide

adequate strength suitable for the installation. Elite Screens is not liable for any faulty

installations. or limit adjustment instructions, please contact our Technical Support

Department at (877) 511-1211 Ext. 604.

The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black

drop in the roller. Please be aware of this as it will void the limitation of your warranty.

Individual modifications to this product are prohibited and will void the warranty with the

manufacturer. Please contact Elite Screens Customer Service for any questions.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications.

owever, there is no guarantee that the interference will not occur on a particular installation. If this

equipment causes harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures.

Reorient or relocate the receiving antenna of the device which may be casing the interference.

Increase the separation between the screen and the device’s receiver.

onnect the equipment into a different power outlet other than the device.

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with

foreign particles such as dust, sawdust, and/or liquids.

Regardless of the mounting method, the screen should be securely supported so that the vibration or

pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure

that the fasteners used are of adequate strength and suitable for the installation location.

Installation Warning

Pre-Installation

NOTE

Rev.102111-AS

www.elitescreens.com [email protected]

Please make sure all accessories listed below are included before proceeding.

A. B. C. D.

IR Remote RF Remote 3 Way Wall Switch IR Eye Receiver

Red+ Green-

E. F. G.

12V Trigger AAA Batteries Bubble Level

Accessories for CineTension 2 Series

Rev.102111-AS

www.elitescreens.com [email protected]

way Wall swit

Stop

5-12 Volt Trigger Cable

Control System for CineTension 2 Series

1. 5

12V Trigger:

The built

in 5

12V trigger input

allows your screen to synchronize its drop & rise

with the projector’s power cycle. The screen

deploys when the projector powers up and will

retract when the projector powers down. The 5-12

volt adaptor connects to your projector’s trigger

output via a separate cable that may or may not

be provided by the manufacturer of the projector.

The trigger feature will not work without an

output cable from the projector, but it can be

tested by connecting the Red (+) and Green (-)

cable to a 9-volt battery.

prong power cable

Red: DC 12 +

Green: 0 V -

45 input for 5

12V Trigger

Way Wall Switch:

The 3

way wall

switch is a wall mount control box with

an up/stop/down button and plugs

directly into the screen’s RJ-45 input.

3. IR “Eye” Receiver:

The IR “Eye” Receiver plugs

directly into the screen’s RJ-45 input to present a low

profile line-of-sight control option for your IR remote

control even in a recessed ceiling installation.

IR “Eye” Receiver

4. IR Remote ontrol:

The Infrared

functions by direct line of sight contact

with a beam range of 30 feet.

5. RF Remote ontrol:

The radio

waves eliminate the need for a direct

line of sight with a range of 150 feet.

Rev.102111-AS

www.elitescreens.com [email protected]

Please make sure all items listed below are included before proceeding with the installation.

Please consult a professional installer. Elite Screens is not liable for any faulty installations.

1. Insert each Bolt (B) through the right & left slide channel located on the top of the screen’s case.

2. Slide the Extruded Hanging Bracket (D) through the rail located below the slide channel until it

meets with the top of the Bolt (B) and slightly secure the lug-nuts located on the top & bottom

of the bolt to attach the bracket.

Hardware Parts List

QTY

Screw & Dry Wall Anchor

2EA.

Bolt

Masonry Screw & Anchor

2EA.

Extruded Hanging Bracket

or 3

Hardware Parts List for CineTension 2 Series

120” & above x 3

brackets

Installation Instructions

Rev.102111-AS

www.elitescreens.com [email protected]

3. Mark the installation location to drill your hole. Insert the proper screw and secure the bolts to

the bracket.

4. Example of the CineTension 2 installed to a wall, ceiling and enclosed.

Adjusting the Tension String

This adjustment is not required. The screen’s tension has been set to achieve its best performance.

Please contact Elite Screens for assistance to avoid damaging the screen and voiding your warranty.

1. If the tension string is loose, pull and turn the tension knob clockwise to tighten the string. To

release the tension, pull and turn the knob counter-clockwise.

Top hole for ceiling installation

Back hole for wall installation

Flush mount

to wall

Flush mount

eiling

En losed

installation

Allow 2” of spa ing

between the front and

ba k of the s reen asing.

Tension Knob

Rev.102111-AS

www.elitescreens.com [email protected]

For additional information, please contact Elite Screens at te[email protected]om

1. If your screen does not move, please check the power supply. The screen will understandably

not move without power.

2. Make sure the power cord is firmly plugged to the power outlet.

3. Make sure that all cable connections are secure.

4. If the screen works well with the line switch but not with the remote control, please make sure

the remote controls have fresh batteries. Change the batteries every 6 months to ensure proper

operation of the remotes.

1. Q: Why does my screen no longer function?

A: Make sure your wall plug has power and that the screen is properly plugged. The fuse on the

screen will also need to be checked. Please contact techsupport@elitescreens.com for the

location. The tubular motor in this screen is equipped with a thermal relay. This feature will

automatically shut off the screen in the event of the motor becoming too hot. This will prevent

the motor from overheating. If you should experience this, please let the screen’s temperature

decrease for 10-15 min. before usage.

2. Q: ow is the screen material cleaned?

A: The screen material can be cleaned with mild soap and water.

3. Q: What type of batteries do the remote controls require?

A: The IR and RF remote controls use AAA alkaline batteries.

4. Q: Can you manually pull down the screen?

A: No, manually pulling down the screen will damage the electronic motor rolling system and

void your warranty.

5. Q: ow could I setup my Screens IR receiver to work with my learning remote control system

Do you have any IR codes I can use to achieve this?

A: Our IR remote controls have been evaluated and entered in to the databases of some

Universal remote control manufacturers. Please contact the manufacturer of your remote to

inquire about your remotes ability to function with ours. If they have not evaluated our remote

control then the following list of Binary codes will be used for most remote setups.

For Spectrum, VMAX2 (Plus), ome2 and ineTension 2 Series

Up: 1111 0000 0001

Stop: 1111 0000 0010

Down: 1111 0000 0100

6. Q: What is the gain on the matte white screen material?

A: The matte white material has a gain of 1.1. For detailed information, please visit

www.elitescreens.com/cinetension2

Troubleshooting & FAQ’S

Rev.102111-AS

www.elitescreens.com [email protected]

Measurement dimensions are intended as a reference only and subject to change without notice Note: Data Error may be ±1"

CineTension 2 Dimension Table

Rev.102111-AS

www.elitescreens.com [email protected]

•Two (2) Year parts and labor warranty from defects in workmanship from purchase date as

follows (except for refurbished units as specified below).

•Three (3) Year parts and labor warranty from defects in workmanship for GEMR (Government,

Educational, Military, & Religious) purchases of new product only.

•Refurbished Units carry a 90-DAY parts and labor warranty.

•Each party will be responsible for one way shipping during the warranty period.

•A RMA (Return Merchandise Authorization) number must be issued in order to process a

replacement or to authorize a return for warranty repair. Elite Screens will, at its sole option

replace or repair the defective unit with a replacement *(see exceptions below) after the

defective unit or parts have been received. Once the product is received, Elite Screens will send

out a replacement *unit to the customer by ground service (subject to inventory availability).

•Do Not Return Any Unauthorized Items to Elite Screens, as they will be refused and returned

at your expense. The RMA Number must be included on the outside label of your shipping

box. Our warehouse is not authorized to accept returns without an RMA number on the

shipping label.

•RMA Numbers are valid for 45 days from the date issued.

•Missing Parts must be reported within 7 days of receipt. If reported after 7 days, the customer

will be responsible for shipping and handling fees. If reported after 30 days of receipt, the

customer will be responsible for cost of parts and shipping & handling fees.

*A New or refurbished replacement will be send out to the customer depending on the type of

purchase (new or refurbished) and based on stock availability.

North America only U.S. and anada

For Warranty and Service requests, please submit an RMA/Service Form at:

www.elitescreens.com/warrantysupportform

Please visit this link for full Warranty information:

www.elitescreens.com/warranty

For Customer Service and Technical questions, please contact Elite Screens at:

Telephone: (877) 511-1211 service@elitescreens.com

Fax: (562) 926-8433 techsupport@elitescreens.com

REMEMBER TO REGISTER YOUR PRODUCT AT:

WWW.ELITESCREENS.COM

Warranty Policy

Otros manuales para CineTension 2 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens Evanesce Plus Series Manual de usuario

Elite Screens

Elite Screens Insta-DE Series Manual de usuario

Elite Screens

Elite Screens F60XWV1 Manual de usuario

Elite Screens

Elite Screens Home100IWH2-A Manual de usuario

Elite Screens

Elite Screens Evanesce Tab-Tension B Series Manual de usuario

Elite Screens

Elite Screens EB100HW2-E12 Guía de referencia rápida

Elite Screens

Elite Screens ezCinema Series Manual de usuario

Elite Screens

Elite Screens F60XWV1 Manual de usuario

Elite Screens

Elite Screens Kestrel Tab-Tension Series Manual de usuario

Elite Screens

Elite Screens Reflexion Series Manual de usuario

Elite Screens

Elite Screens Elite Home Series Manual de usuario

Elite Screens

Elite Screens M92UWH Manual de usuario

Elite Screens

Elite Screens F100XWH1 Manual de usuario

Elite Screens

Elite Screens Tripod B Series Manual de usuario

Elite Screens

Elite Screens Manual SRM Pro Series Manual de instrucciones

Elite Screens

Elite Screens Spectrum Series Manual de usuario

Elite Screens

Elite Screens Home100IWH3 Manual de usuario

Elite Screens

Elite Screens aeonclr series Manual de usuario

Elite Screens

Elite Screens Sable Frame CineGrey 3D Manual de usuario

Elite Screens

Elite Screens Home100IWH2-A Manual de usuario

Elite Screens

Elite Screens Yard Master 2 Series Manual de usuario

Elite Screens

Elite Screens Kestrel Series Manual de usuario

Elite Screens

Elite Screens DE103C82H Manual de usuario

Elite Screens

Elite Screens AEON series Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación