Elenco Electronics K-38 Guía del usuario

CAPACITANCE SUBSTITUTION BOX

MODEL K-38

Assembly and Instruction Manual

Elenco®Electronics, Inc.

No part of this book shall be reproduced by any means; electronic, photocopying, or otherwise without written permission from the publisher.

PARTS LIST

If you are a student, and any parts are missing or damaged, please see instructor or bookstore.

If you purchased this kit from a distributor, catalog, etc., please contact Elenco®Electronics (address/phone/e-

mail is at the back of this manual) for additional assistance, if needed. DO NOT contact your place of purchase

as they will not be able to help you.

CAPACITORS

Qty. Symbol Description Part #

1 R1 100pF (101) 50V 221017

1 R2 150pF (151) 50V 221510

1 R3 220pF (221) 50V 222210

1 R4 330pF (331) 50V 223317

1 R5 470pF (471) 50V 224717

1 R6 560pF (561) 50V 225610

1 R7 680pF (681) 50V 226880

1 R8 820pF (821) 50V 228210

1 R9 1000pF (102) 50V 231035

1 R10 1500pF (152) 50V 231516

1 R11 2200pF (222) 50V 232216

1 R12 3300pF (332) 50V 233310

1 R13 .0047μF (472) 50V 234710

1 R14 .0056μF (562) 100V 235618

1 R15 .0068μF (682) 50V 236810

1 R16 .0082μF (822) 100V 238218

1 R17 .01μF (103) 100V 241017

1 R18 .015μF (153) 100V 241517

1 R19 .022μF (223) 100V 242217

1 R20 .033μF (333) 100V 243317

1 R21 .047μF (473) 100V 244717

1 R22 .056μF (563) 100V 245618

1 R23 .068μF (683) 100V 246818

1 R24 .1μF (104) 100V 251017

MISCELLANEOUS

Qty. Description Part #

1 PC Board 517007

1 PC Mount Switch 541103

2 12 Position Switch 542013

2 Knob 622009

1 Case w/ Cover and Screws 62CS440

2 Nut 9mm 644102

2 Washer 9mm x 15mm 645103

1 Alligator Clip Black 680001

1 Alligator Clip Red 680002

12” Wire Black Stranded 814210

12” Wire Red Stranded 814215

-1-

The Capacitance Substitution Box is a convenient instrument in determining the desired capacitance values in

circuits under design or test. The values selected for your capacitance substitution box were determined to be

the most commonly used in modern solid-state circuits. The values are from 100pF to .1μF in 24 steps.

-2-

PARTS IDENTIFICATION

Switch 12 Position 9mm Nut

Alligator Clip

Switch PC Mount

Capacitor

Washer

PC Board

IDENTIFYING CAPACITOR VALUES

Capacitors will be identified by their capacitance value in pF (picofarads), nF (nanofarads), or μF (microfarads). Most

capacitors will have their actual value printed on them. Some capacitors may have their value printed in the following

manner. The maximum operating voltage may also be printed on the capacitor.

Second Digit

First Digit

Multiplier

Tolerance

The letter M indicates a

tolerance of +20%

The letter K indicates a

tolerance of +10%

The letter J indicates a

tolerance of +5%

FortheNo.01234589

Multiply By 1 10 100 1k 10k 100k .01 0.1

Multiplier

Note: The letter “R” may

be used at times to

signify a decimal point;

as in 3R3 = 3.3

103K

100V

Maximum

Working Voltage

The value is 10 x 1,000 = 10,000pF or .01μF 100V

10μF 16V

METRIC UNITS AND CONVERSIONS

Abbreviation Means Multiply Unit By Or

p Pico .000000000001 10-12

n nano .000000001 10-9

μmicro .000001 10-6

m milli .001 10-3

– unit 1 100

k kilo 1,000 103

M mega 1,000,000 106

1. 1,000 pico units = 1 nano unit

2. 1,000 nano units = 1 micro unit

3. 1,000 micro units= 1 milli unit

4. 1,000 milli units = 1 unit

5. 1,000 units = 1 kilo unit

6. 1,000 kilo units = 1 mega unit

Electrolytic capacitors have a positive

and a negative electrode. The negative

lead is indicated on the packaging by a

stripe with minus signs and possibly

arrowheads.

Warning:

If the capacitor is

connected with

incorrect polarity, it

may heat up and

either leak, or

cause the capacitor

to explode.

Polarity

Marking

-3-

Introduction

The most important factor in assembling your K-38 Capacitance Substitution Box Kit is good soldering

techniques. Using the proper soldering iron is of prime importance. A small pencil type soldering iron of 25 -

40 watts is recommended. The tip of the iron must be kept clean at all times and well tinned.

Safety Procedures

• Wear eye protection when soldering and during all phases of construction.

• Locate soldering iron in an area where you do not have to go around it or reach over it.

•Do not hold solder in your mouth. Wash your hands thoroughly after handling solder.

• Be sure that there is adequate ventilation present.

Assemble Components

In all of the following assembly steps, the components must be installed on the top side of the PC board unless

otherwise indicated. The top legend shows where each component goes. The leads pass through the

corresponding holes in the board and are soldered on the foil side.

Use only rosin core solder.

DO NOT USE ACID CORE SOLDER!

CONSTRUCTION

Solder Soldering Iron

Foil

Solder

Soldering Iron

Foil

Component Lead

Soldering Iron

Circuit Board

Foil

Rosin

Soldering iron positioned

incorrectly.

Solder

Gap

Component Lead

Solder

Soldering Iron

Drag

Foil

1. Solder all components from

the copper foil side only.

Push the soldering iron tip

against both the lead and

the circuit board foil.

2. Apply a small amount of

solder to the iron tip. This

allows the heat to leave the

iron and onto the foil.

Immediately apply solder to

the opposite side of the

connection, away from the

iron. Allow the heated

component and the circuit

foil to melt the solder.

1. Insufficient heat - the

solder will not flow onto the

lead as shown.

3. Allow the solder to flow

around the connection.

Then, remove the solder

and the iron and let the

connection cool. The

solder should have flowed

smoothly and not lump

around the wire lead.

Here is what a good solder

connection looks like.

2. Insufficient solder - let the

solder flow over the

connection until it is

covered. Use just enough

solder to cover the

connection.

3. Excessive solder - could

make connections that you

did not intend to between

adjacent foil areas or

terminals.

4. Solder bridges - occur

when solder runs between

circuit paths and creates a

short circuit. This is usually

caused by using too much

solder. To correct this,

simply drag your soldering

iron across the solder

bridge as shown.

What Good Soldering Looks Like

A good solder connection should be bright, shiny,

smooth, and uniformly flowed over all surfaces.

Types of Poor Soldering Connections

-4-

ASSEMBLY INSTRUCTIONS

Begin the PC board assembly with the 100pF capacitor placed in position R1. Be sure to

identify the correct value. Bend the leads to fit. Place the capacitor into the PC board with

the leads coming out on the copper foil side. Solder into place and clip off the excess

leads.

R9 - 1000pF (102) 50V Cap.

R7 - 680pF (681) 50V Cap.

R8 - 820pF (821) 50V Cap.

R10 - 1500pF (152) 50V Cap.

R11 - 2200pF (222) 50V Cap.

R12 - 3300pF (332) 50V Cap.

R1 - 100pF (101) 50V Cap.

R2 - 150pF (151) 50V Cap.

R3 - 220pF (221) 50V Cap.

R5 - 470pF (471) 50V Cap.

R6 - 560pF (561) 50V Cap.

R4 - 330pF (331) 50V Cap.

R22 - .056μF (563) 100V Cap.

R24 - .1μF (104) 100V Cap.

R23 - .068μF (683) 100V Cap.

R21 - .047μF (473) 100V Cap.

R20 - .033μF (333) 100V Cap.

R19 - .022μF (223) 100V Cap.

R18 - .015μF (153) 100V Cap.

R17 - .01μF (103) 100V Cap.

R16 - .0082μF (822) 100V Cap.

R14 - .0056μF (562) 50V Cap.

R13 - .0047μF (472) 100V Cap.

R15 - .0068μF (682) 50V Cap.

-5-

SW3 - PC Mount Switch

Mount SW3 in the place shown on the PC board.

Solder into place.

Red Test Lead

Black Test Lead

Cut off 1 1/2” of wire off of both the red and black

wires (SAVE them for later use). Strip 1/4” of

insulation off both ends of the 10 1/2” red and black

wires and insert them into the holes as marked on

the PC board. Solder into place. Tie a knot with

both wires 1 1/2” from the surface of the PC board

as shown in Figure 1. Pull the wires through the

hole in the cover. Slide the alligator boots onto the

wires. Solder the wires to the alligator clips. Then,

slide the boots onto the clips.

SW1

SW2

Bend the tab on the switches

down (see Figure 2). Attach the

two switches loosely to the front

panel with the 9mm nuts and

washers. Line up the holes of

the PC board with the switch

lugs, as shown in Figure 3. Be

sure that the board lays flat,

then solder the lugs into place.

Tighten down the 9mm nuts.

Jumper wire from SW1

Jumper wire from SW2

Strip 1/4” of insulation off of both ends of the 1 1/2”

red and black wires. Solder one end of the wire to the

wiper pin on the 12 position switches and the other to

the pad without a hole, as shown in Figure 4.

Installation of Knobs if Capacitance Meter is

Available

Place the knobs loosely on the switch posts. Push

the slide switch to the PFD position. Connect a

capacitance meter to the output. Line up the pointer

of the knob with the value shown on your meter, then

push the knob onto the shaft. Push the slide switch

to the MFD position and repeat the same procedure.

Figure 4

SW1

SW2

Wiper Pin Wiper Pin

Jumper Wires

Figure 3

9mm Nut

Washer Cover

Figure 2

Bend Tab Over

Figure 1

PC Board

Bend Tabs

Over Wire

-6-

Installation of Knobs without Capacitance Meter

If a capacitance meter is not available, turn both

switches so that the wiper contact is in the position

shown in Figure 5. Start with switch SW1, follow the

copper run on the PC board from the lug in contact

with the wiper to the 680pF (R7) capacitor, to be

sure that the switch is set in the proper position.

Align the knob on the SW1 (PFD) switch to the

680pF position, push the knob onto the shaft.

Follow the same procedure for switch SW2 (MFD),

except follow the copper run to the .0047μF (R13)

capacitor. Align the knob on the SW2 (MFD) switch

to the .0047μF position.

TESTING THE CIRCUIT

SCHEMATIC DIAGRAM

SW1 PFD POSITION

Value Position Meter Reading

100pF

150pF

220pF

330pF

470pF

560pF

680pF

820pF

1000pF

1500pF

2200pF

3300pF

SW2 MFD POSITION

Value Position Meter Reading

.0047μF

.0056μF

.0068μF

.0082μF

.01μF

.015μF

.022μF

.033μF

.047μF

.056μF

.068μF

.1μF

Note: Capacitors being tested have a 10% tolerance. Because of lead capacitance from the alligator clips to

the PC board, all values will read 30pF +10pF above the actual capacitance value.

Figure 5

Wiper Contact

LugPC Board

Elenco®Electronics, Inc.

150 Carpenter Avenue

Wheeling, IL 60090

(847) 541-3800

Website: www.elenco.com

e-mail: elenco@elenco.com

Tabla de contenidos

Otros manuales de Instrumento de medición de Elenco Electronics

Elenco Electronics

Elenco Electronics XK-550 Manual de usuario

Elenco Electronics

Elenco Electronics TWT-1 Manual de usuario

Elenco Electronics

Elenco Electronics DT-100K Guía del usuario

Elenco Electronics

Elenco Electronics CS-600 Manual de usuario

Elenco Electronics

Elenco Electronics LP-525K Guía del usuario

Elenco Electronics

Elenco Electronics XK-700 Manual de usuario

Elenco Electronics

Elenco Electronics TT-400K Guía del usuario

Elenco Electronics

Elenco Electronics XK-700 Manual de usuario

Elenco Electronics

Elenco Electronics XK-550K Guía del usuario

Elenco Electronics

Elenco Electronics XK-700K Guía del usuario

Elenco Electronics

Elenco Electronics CS-440 Guía del usuario

Elenco Electronics

Elenco Electronics XK-700-SEMI Guía del usuario

Elenco Electronics

Elenco Electronics K-37 Guía del usuario

Elenco Electronics

Elenco Electronics M-2666K Guía del usuario

Elenco Electronics

Elenco Electronics TWT-1K Guía del usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario