ElektraLite Mini Stingray Variable White Manual de usuario

Mini Stingray

Variable White

USER MANUAL

Elektralite (a division of Group One),

70, Sea Lane, Farmingdale, NY11735, U.S.A.

T. +1 (631)-396-0184. F. +1 (631)-396-0190

WWW.MYELEKTRALITE.COM

1. Unpacking

Thank you for choosing the Elektralite Variable White Mini Stingray fixture. For your own safety, please read this manual before

installing the fixture. This manual covers important information on installation and applications. Please keep this manual for future

reference.

To keep this simple, we are going to refer to the fixture as the Elektralite VW Mini Stingray throughout the manual.

The Elektralite VW Mini Stingray fixture uses a single COB led with a balanced array of elements giving incredible output.

Please unpack it carefully and check whether it was damaged in shipping.

The following items should be in the box with the fixture:-

Power cable with Edison connector

Jumper cable to extend DMX module away from the fixture yoke.

2. Safety Instructions.

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is

absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. The Elektralite

VW Mini Stingray is a high voltage fixture. Be careful when dealing with high voltages.

Please read this manual. If you do not read this manual and damages occur to the Elektralite VW Mini Stingray, then it

could void the warranty.

During shipping, Elektralite VW Mini Stingray may have been exposed to high temperature changes or humidity changes. So,

as a precaution, do not switch Elektralite VW Mini Stingray on immediately. Condensation can damage Elektralite VW Mini

Stingray so leave it switched off, until it has reached room temperature.

The electric connection must be carry out by a qualified person.

Always disconnect the Elektralite VW Mini Stingray from the power source, when the device is not in use or before cleaning it.

Only unplug Elektralite VW Mini Stingray from the power cord. Never pull out the plug out by pulling on the power cord.

Please keep the Elektralite VW Mini Stingray away from children and the general public. Please be intelligent and use common

sense when operating the Elektralite VW Mini Stingray.

3. General Guidelines.

The Elektralite VW Mini Stingray is a lighting fixture for professional use on stages, in churches, theatres, etc.

The Elektralite VW Mini Stingray should only be operated at 120 volts and only indoors.

The Elektralite VW Mini Stingray should not be operated 24/7 (24 hours a day; 7 days a week). The Elektralite VW Mini

Stingray needs operation breaks to ensure that it will work for a long time without problems. Please do not shake the Elektralite

VW Mini Stingray and avoid using brute force when installing or operating it.

When choosing the location to install the Elektralite VW Mini Stingray, please make sure that it is not exposed to extreme heat,

moisture or dust. The minimum distance between the Elektralite VW Mini Stingray and the illuminated surface must be more

than 3 feet.

Always mount the Elektralite VW Mini Stingray with an appropriate safety cable/chain.

Operate the Elektralite VW Mini Stingray only when you are familiar with the features on the fixture. Do not permit operation by

persons not qualified to operate it.

All modifications to the Elektralite VW Mini Stingray will invalidate the warranty. There are absolutely no exceptions.

If Elektralite VW Mini Stingray is operated in any way different to the one described in this manual, the Elektralite VW Mini

Stingray maybe damaged and the guarantee will be void.

4. Main Features.

• 1*20W COB LED (2in1 Warm white + Cool white)

• Color Rendering Index (CRI): Ra≥90

• Optimized high definition optical system for improved photometric performance and field uniformity

• Projector-quality, high contrast aspheric lens

• Glass reflector that removes greater than 90% infrared radiation (heat) and reflects greater than 95% of visible light

• Power Max: 20W

• Housing made utilizing rugged, die-casting aluminum

• Flat even field giving a spot image

• Smooth manual focus system

• Beam edge continually adjustable hard-to-soft

• Thermally insulated rear handle

• Thermally insulated knobs and single aluminum handle for installing

• Metal gobo slot (for use with gobo holder : sold separately. Diameter of hole is 25.4mm = 1”).

• Color/Gel frame slot (for use with color/gel frame : sold separately. Frames are square 70mm = 2.755”).

• 4 Metal shutter blades

• 0-100% Smooth and precise linear dimmer

• 25T/sec high speed shutter/strobe effect with variable speed

• 2 personality profiles for operation as either 2 channel or 5 channel DMX.

• DMX512, master-slave, and sound control or auto operation

• 4-Button digital display

• 5-Pin XLR connectors IN and THRU

• Fanless cooling system

• -30~40°C Max ambient temperature

• IP20 protection rating

All measurements are in MM. I inch is equal to 25.4mm.

4. Changing Lenses.

The Elektralite VW Mini Stingray can accept a variety of different lenses. When replacing the lens remove the thumb screw but

be careful that the lens does not fall out of the body of the fixture.

5. Installation

Please ensure that the Elektralite VW Mini Stingray is hung using the appropriate "C" clamp or half cheeseboro. A safety chain

or cable should also be used as a secondary point of holding the fixture in case the clamp comes loose. Never hang the fixture

without a safety chain or cable. If a Color/Gel frame (Color/Gel holder) has been purchased separately please ensure that it is

clipped into position correctly and cannot come loose.

If you are not qualified or have any doubts about hanging the Elektralite VW Mini Stingray then do NOT hang it.

Do not clamp the cable to the U bracket or clamp. That is not a secondary safety point.

A secondary safety point is any point that will adequately hold the Elektralite VW Mini Stingray if the "C" clamp or half

cheesboro fails. Then the safety cable would be the backup and stop the fixture from falling to the ground. So do NOT fix the

safety to the same place that the "C"clamp is attached.

Installation during construction.

Many times fixtures are installed during the construction phase of a building. It is imperative that the fixture is protected during this

phase. A lot of dust is usually created. This dust can adversely affect the fixture. Specifically, of course, in coating the lenses and

therefore reducing the output. It can also damage electronics which can lead to the fixture failing immediately or prematurely in its

life cycle. If covering the fixture is determined to be the best solution, MAKE SURE THE FIXTURE IS DISCONNECTED FROM

ALL ELECTRICAL POWER. The fixture does generate heat and it can burn items that are brought within close proximity. So do

not have power to the fixture.

6. DMX-512 Control and Power input Connections

Connect an XLR cable (not provided) to the female 5-pin XLR output of the DMX controller The other end should be connected to

the male 5-pin XLR input of the Elektralite VW Mini Stingray . Then daisy-chain out of the first Elektralite VW Mini Stingray

and into the next Elektralite VW Mini Stingray or other dmx device. Never “Y” split the DMX connection.

If you need more cable, then it should be two core, screened cable fitted with a 5 pin XLR input and output connector. Please refer

to the diagram below.

DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically “noisy” environment, it is recommended

that a DMX terminator is used. This helps prevent corruption of the digital control signal. The DMX terminator is simply a 5 pin

XLR plug (male) with a 120 Ω resistor connected between pins 2 and 3. It is then plugged into the output XLR socket of the last

Elektralite VW Mini Stingray or other dmx device in the chain. Please see illustration below.

120

The DMX module and integral power supply

7. Menus in the fixture.

Press the MENU button to change the menu

On the Screen Description Operation

Advanced DMX Use the ↑ or ↓ buttons to choose

the DMX starter address. Press

the ENTER button to save.

“A” uses the 5 channel dmx

profile for the fixture

dMX

“d” uses the 2 channel dmx

profile for the fixture.

SLAve

The profile will be the same

as “d001”

In slave mode :-

1、Make sure there is only one master fixture

2、The slave fixture(s) will copy exactly the signal sent to the master.

Color Fade Use the ↑ or ↓ buttons to choose

Note that the speed can be varied

from 1~50. Press the ENTER

button to save. (for clarification

Color is actually color temperature

of the white).

gradual change

Color Jump

Jump change

Color Pulse

Pulse change

Static Use the ↑ or ↓ buttons to choose

the output level (brightness) for

the cool white leds and then the

warm white leds.

Change color

Strobe Use the ↑ or ↓ buttons to choose

the speed of the strobe from 1 to

50. Press ENTER to save.

Strobe

Sound a “clap” or loud noise will turn the

led output “on” or “off”.

There is a “Sub Menu” to the Sound root menu. See following page.

8. Sound Sub menus.

When the screen displays the word “Sound” if the “enter button is pressed and held down for several seconds, then a new

Sub Menu is activated with the following parameters.

On the

Screen

Description Operation Description

LED time “on” Use the ↑ or ↓ buttons to

choose the screen “on” time

0 = screen is always “on”

Screen protect time

High Power Use the ↑ or ↓ buttons to

choose led maximum output or

run the led at max 33.3% output

On = 100%

off = 33.3%

Power choose

dMX-controller delay Use the ↑ or ↓ buttons to

choose to use controller delay

or not

controller delay

Synchronization Use the ↑ or ↓ buttons to

choose use multi-light

synchronization or not

Multi-light

synchronization

LoAd Hold down the ENTER button

until the display reads “LdEd”

i.e. loaded.

reset

rEturn Press ENTER to save the data

and get back to the main menu.

Back to function menu

9. Fixture Personality.

There are just two fixture personalities or profiles and they are as follows

Channel Data Function

1 0~255 Master Dimmer

2 0~255 Cool white

3 0~255 Warm White

4 0~5 No function

6~255 Strobe: 6 is slowest, 255 is fastest

5 0~25 Turn on “delay by controller”

26~100 Turn off “delay by controller”

101~150 Cool white will fade up & then down followed by warm white fading up and

down. 101 is slowest, 150 is fastest.

151~200 Cool white then “snap” to warm white then “snap” to black out then repeat.

151 is slowest, 200 is fastest.

201~250 Cool white then Xfade to warm white then back to cool white. 201 is

slowest, 250 is fastest.

251~255 Sound mode: the changing of the light depends on the MIC of each light

Channel Data Function

1 0~255 Cool white

2 0~255 Warm white

10. Cleaning and maintenance.

Now ignoring maintenance and cleaning is very good way of creating problems "down the road" and many companies and

installations do just that. However the net result is, no matter what the fixture, premature failure!

Changing the oil in a car most people do on a regular basis.

So with the fixtures, regular maintenance is an excellent practice, if you want the fixtures to last.

So what is the maintenance for the fixture? Keep it clean. Dust and dirt accumulation can stop the body’s heat sink from

adequately keeping the COB led cool. Heat can destroy the led, the lens and other components. So just keep it clean.

The lenses should also be cleaned so the light output is maintained. Use only a moist lint-free cloth. Never use alcohol or solvents

to clean the fixture.

11. Technical Specification.

 Operating voltage 100 – 240v

 Frequency 50 – 60 Hertz

 36 x 5 watt leds

 Fan cooled

 269.75mm x 122mm x 122mm

 11" x 5" x 5"

 2.0 kgs

 4.4 pounds

Elektralite is a division of Group One. Group One and its divisions are constantly improving their product range and we

reserve the right to make changes without prior notice.

Tabla de contenidos

Otros manuales de Foco de elektraLite

elektraLite

elektraLite eyeBall Manual de usuario

elektraLite

elektraLite eyeBall RGBWA Manual de usuario

elektraLite

elektraLite eyeBall RGBWA Manual de usuario

Manuales populares de Foco de otras marcas

VIZULO

VIZULO Micro Martin Guía del usuario

EuroLite

EuroLite LED IP FL-100 SMD Manual de usuario

Cooper Wheelock

Cooper Wheelock XB12 Manual de usuario

Allen + Roth

Allen + Roth 17624-000 Manual de usuario

ADJ

ADJ 4 STAGE PAK Manual de usuario

Cooper Lighting

Cooper Lighting EGL91SW233 Manual de usuario

Max

Max 37496 Manual de usuario

BEGA

BEGA 85 143 Manual de usuario

Beamz

Beamz 151.226 Manual de usuario

EuroLite

EuroLite LED IP FL-8 Manual de usuario

Ledj

Ledj PERFORMER 36 RGB Manual de usuario

Perel

Perel ELS3 Manual de usuario

Perel

Perel ELS3WD Manual de usuario

LumX

LumX LM 36130 Manual de usuario

Xtricity

Xtricity 4-80053 Manual de usuario

Stahl

Stahl 6521/4 Series Manual de usuario

Ecosense

Ecosense EcoSpec Manual de usuario

Ayrton

Ayrton minipanel FX Manual de usuario

elektraLite Mini Stingray Variable White Manual de usuario

Manuales populares de Foco de otras marcas