ElektraLite EyeBall Manual de usuario

ElektraLite LED

eyeBall Warm White

USER MANUAL

ElektraLite (a division of Group One),

70, Sea Lane, Farmingdale, NY 735, U.S.A.

T. + (63 )-396-0 84. F. + (63 )-396-0 90

WWW.MYELEKTRALITE.COM

. Unpacking

Thank you for choosing the elektraLite WW fixture For your own safety, please read this manual before

installing the device This manual covers important information on installation and applications Please

keep this manual for future reference For the rest of the manual we are going to refer to the fixture as

elektraLite WW.

The elektraLite WW wash fixture uses 18 high powered leds, run in a balanced arrangement giving

incredible output Please unpack the elektraLite WW carefully and check whether it was damaged in

shipping

The following item should be in the box with the fixture:-

2 part yoke

2 knobs for yoke

1 DMX 5 pin cable

1 Turnaround 3 to 5 pin cable

1 Turnaround 5 to 3 pin cable

1 IEC power cable

1 IEC jumper cable (for daisy chaining the power between fixtures)

Please handle the fixture with care at all times. Do not drop. Do not hit the front lens assembly.

2. Safety Instructions.

This device has left the factory in perfect condition In order to maintain this condition and to ensure a

safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes

written in this user manual elektraLite WW is a high voltage fixture Be careful when dealing with high

voltages

Please read this manual. If you do not read this manual and damages occur to the elektraLite WW,

then it could void the warranty.

During shipping, the elektraLite WW may have been exposed to high temperature changes or humidity

changes So, as a precaution, do not switch the ElektraLite WW on immediately Condensation can

damage the ElektraLite WW so leave the ElektraLite WW switched off until it has reached room

temperature The ElektraLite WW is an INDOOR operational fixture Do not operate this fixture

outdoors or anywhere there is high humidity.

The electric connection must carry out by a qualified person and it is absolutely essential that the

ElektraLite WW be grounded So under no circumstances break off the ground pin on the Edison plug or

use the fixture where a ground is not present A ground pin, like the fuse for the ElektraLite WW is there

for safety

Always disconnect the ElektraLite WW from the power source, when the fixture is not in use or before

cleaning it Only unplug ElektraLite WW from the power source holding onto the Edison plug Never pull

out the Edison plug out by just pulling on the power cord itself

Please keep the ElektraLite WW away from children and the general public Please be intelligent and

use common sense when operating the ElektraLite W W.

3. General Guidelines.

ElektraLite WW is a lighting fixture for professional use on stages, in clubs, theatres, churches etc

ElektraLite WW should only be operated at between 120 to 240 volts and only indoors

ElektraLite WW should not be operated 24/7 (24 hours a day; 7 days a week) ElektraLite WW needs

operation breaks to ensure that it will work for a long time without problems Please do not shake the

ElektraLite WW and avoid using brute force when installing or operating it

Please read this below. It is important to understand and realize the following:-

The lens encapsulates each of the leds This way the maximum output is attained However this means

that, if the fixture is dropped or the front lens assembly is struck, then it is possible for leds to be crushed

So please exercise care and attention This is not a par64 that can be abused at will!

When choosing the location to install the ElektraLite WW, please make sure that it is not exposed to

extreme heat, moisture or dust and never install it outdoors Make sure that the fixture has a good amount

of free space around it for air flow Do not install it in a confined space or have insulation around the

fixture The minimum distance between the ElektraLite WW and the illuminated surface must be more

than 3 feet

Always mount the ElektraLite WW with an appropriate safety cable

Operate the ElektraLite WW only when you are familiar with the features on the fixture Do not permit

operation by persons not qualified

All modifications to the ElektraLite WW will invalidate the warranty. There are absolutely no

exceptions.

If ElektraLite WW is operated in any way different to the one described in this manual, ElektraLite WW

maybe damaged and the guarantee will be void

4. Installation

Please ensure that the ElektraLite WW is hung using the appropriate "C" clamp or half cheeseboro A

safety chain or cable should also be used as a secondary point of holding the fixture in case the clamp

comes loose Never hang the fixture without a safety chain or cable Make sure the Gel frame (Gel

holder) is clipped into position correctly and cannot come loose

If you are not qualified or have any doubts about hanging the ElektraLite WW then do NOT hang it

Do not clamp the safety cable to the U bracket or clamp That is not a secondary safety point

A secondary safety point is any point that will adequately hold the ElektraLite WW if the "C" clamp or half

cheesboro fails Then the safety cable would be the backup and stop the fixture from falling to the ground

So do NOT fix the safety cable to the same place that the "C"clamp is attached

5. DMX-5 2 Control Connection

Connect an XLR cable to the female 5-pin XLR output of your ElektraLite CP 6/24 or other DMX

controller The other end should be connected to the male 5-pin XLR input of the ElektraLite WW Then

daisy-chain out of the first ElektraLite WW into the next ElektraLite WW or other dmx device Never “Y”

split the DMX connection

If you need more cable, then it should be two core, screened cable fitted with a 5 pin XLR input and

output connector Please refer to the diagram below

DMX-5 2 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically “noisy”

environment, it is recommended that a DMX terminator is used This helps prevent corruption of the

digital control signal The DMX terminator is simply a 5 pin XLR plug (male) with a 120 Ω resistor

connected between pins 2 and 3 It is then plugged into the output XLR socket of the last ElektraLite WW

or other dmx device in the chain Please see illustration below

6. Menus in the fixture.

Root Menu Sub Menu 1 Sub Menu 2

STAT (STATIC LOOK) WW 000-255

STROBE 000-255

AUTO (AUTOMATIC PROGRAMS) EFFECT 1 (inbuilt program 1)

EFFECT 2 (inbuilt program 2)

EFFECT 3 (inbuilt program 3)

RUN DMX 512

SLAVE

ADDRESS ASSIGN DMX CHANNEL 001-512

ASSIGN ID ADDRESS 001-255

PERS (PERSONALITY) STAG(E) 1

STAG(E) 2

CHANNEL 1

SETTINGS DIMMER (FADE CURVE) 000(OFF) TO 004(LONGEST)

RESET PASSWORD REQUIRED

FANS OFF

AUTO

LOW

NORMAL

HIGH

KEY OFF

7. Static Look.

The ElektraLite WW can be set to a single static look quickly

Use the Menu button to get to STAT

Press Enter

The next screen will read Warm 000 This is addressing the WW leds

Use the ↑ or ↓ to increase brightness of the cool leds

Numbers are expressed in DMX values so 0 is no output and 255 is highest output

Press Enter to save the value

The screen will automatically advance to the strobe function

If the strobe function is to be in the static look, then use the ↑ or↓ to crease the value of strobes flash rate

Press Enter to save the value

This is the last entry and the static look is complete Pressing the Enter key just continues around if you

need to make fine adjustments to the static look

Do not press MENU as this will get you out to the Root directory and out of the static look

8. Auto Programs.

In Auto Program there are three programs (or shows) in the ElektraLite WW are Effect 1, Effect 2 and

Effect 3 Chose the one best suit for the venue

To run a color or program in Auto mode use the Menu button to get to AUTO

Press ENTER

Use the ↑ or ↓ key to get to the program Press Enter

The program will start running

9. Run.

Run allows the fixture to operate in either DMX or Slave operation

Using the Menu button in the root menu go to RUN

Press Enter to get to DMX mode To get to SLAV mode use the ↑ or ↓

And press enter to save this setting

0. Address (For DMX & ID)

DMX Address

Sets up the address for the dmx

Using the Menu button in the root menu go to DMX

Press Enter to get into DMX and the display will read the current dmx channel

The display will read for example DMX:

This means the fixture's current address is

To change it, use the ↑ or ↓ buttons to get to the correct address Press Enter to save the address

Now immediately Enter is pressed, the ID address for the fixture is shown See below for ID address

information; otherwise press Enter to exit out and back to the Root Menu again

ID Address

An ElektraLite WW can be addressed (controlled) through the dmx or instead it can have its own unique

ID address

There are a total of 255 different ID addresses from 001 to 255

To set up the address for a fixture, use the Menu button in the root menu go to ID

Press Enter and then using the ↑ or ↓ buttons,to select the ID address

Press Enter to save the address

For the ID address to work you must chose a Personality that uses the ID For example STAG

This allows you to access the ID address system on channel 4

Set the DMX address to 001 for the fixture So if ID address 123 is chosen then go to channel 4 on the

lighting board and set the level at 123 You will then be controlling only fixture(s) with ID address 123

ID address 001 is the default and in ID address 001 all fixtures will be under control

. Personalities.

There are three different choices on how the fixture will operate

What these "Personalities" do in terms of their channel assignments is detailed in the tables on page 7

To change a Personality use the Menu button to get to PERS

Press Enter then using the ↑ or ↓ buttons go to the personality required

Press Enter to save the Personality

2. Settings. (Set has several Sub Menus which allow the following functions to be used).

1) Dimmer

The Dimmer function allows different Dimmer curves to be chosen There are 5 choices

Choice 1:- this is Dim off The Dimmer curve is 0 which means any change in dimmer level is

instantaneous

Choice 2:- Dim 1 The dimmer curve has the shortest fade in and fade out time

Choice 3:- Dim 2 The dimmer curve has the 2nd shortest fade in and fade out time

Choice 4:- Dim 3 The dimmer curve has the 3rd shortest fade in and fade out time

Choice 5:- Dim 4 The dimmer curve has the longest fade in and the fade out time

To access the DIM function go through the Root Menu until DIMMER is found Press Enter and then use

the ↑ or ↓ buttons to get to the DIM choice required

2) Reset

This resets all values to their default

Go through the Root Menu until Settings is displayed Press Enter and then use the ↑ or ↓ buttons to get

to RESET Press Enter The display will have the cursor flashing across the bottom The password needs

to be entered The password is the following sequence using the ↑ and ↓ buttons

↑ ↓ ↑ ↓ ↑ ↓ then press Enter once complete The display will read OK followed by a return to the

RESET sub menu The Menu button will need pressing to return to the Root Menu Only once at the Root

Menu will the dmx control function once more Please note the Reset also takes the dmx address back to

001

3 Fans

There are several different control options for the fans

Auto:- The fans come on when the temperature exceeds its pre-set value

The fan turns off when the temperature falls below its pre-set value

High:- The fans are constantly on at a high rotational speed

Normal:- The fans are constantly on at their normal rotational speed

Low:- The fans are constantly on at a lower than normal level If the leds exceed their operational pre-set

temperature level, then the output is reduced as the fans are "locked" at lower rotational speed

Off:- The fans are sent to be OFF If the leds exceed their operational pre-set temperature level, then the

output is reduced as the fans are "locked" OFF

4. Key Lock

The Key function is an access password for the fixture The KEY can be turned OFF or ON which then

deactivates or activates the password

To set the KEY LOCK on, go through the Root Menu until KEY LOCK is found. Press Enter and use the ↑

or ↓ to set the KEY LOCK to either OFF or ON If the Key LOCK is turned ON then a password is

required to go into sensitive Menus and to change functions

The password is ↑ ↓ ↑ ↓ ↑ ↓ (Up + Down + Up + Down + Up + Down) Enter

5. DMX Channel Assignments for Personalities.

STAG ：

1 0-255 WW output…dimming

0-50 Linear dimmer speed（DIM=0）

51-100 Non-linear dimmer speed 1（DIM=1）

101-150 Non-linear dimmer speed 2（DIM=2）

151-200 Non-linear dimmer speed 3（DIM=3）

201-255 Non-linear dimmer speed 4（DIM=4）

STAG2:

CH DMX data Function

1 0-255 WW output… dimming

0-9 STROBE

NO FUNCTION

10-49 Synchronous slow flash

50-99 Asynchronous slow flash

100-149 Random slow flash

150-199 Asynchronous fast flash

200-255 Synchronous fast flash

0-10 NO FUNCTION

11-20 FAN OFF

21-25 FAN LOW

26-30 FAN HIGH

31-40 FAN AUTO

41-100 NO FUNCTION

101-150 EFFECT 1

151-200 EFFECT 2

201-255 EFFECT 3

4 0 All ID operating together

1-255 Only the ID number chosen will be controlled

0-50 Linear dimmer speed（DIM=O）

51-100 Nonlinear dimmer speed 1（DIM=1）

101-150 Nonlinear dimmer speed 2（DIM=2）

151-200 Nonlinear dimmer speed 3（DIM=3）

201-255 Nonlinear dimmer speed 4（DIM=4）

CHANNEL ：

1 0-255 WW output…dimming

6. Cleaning and maintenance.

Now ignoring maintenance and cleaning is very good way of creating problems "down the road" and

many companies and installations do just that However the net result is, no matter what the fixture,

premature failure!

Changing the oil in a car most people do on a regular basis

So with the fixtures regular maintenance it an excellent practice, if you want the fixtures to last

So what is the maintenance for the fixture?

Clean the fan! That’s really it!

Turn off the ElektraLite WW.

Using a small vacuum cleaner, suck the dust and “fur balls” out

Do not use a can of co² That will just blast the dust and dirt everywhere!

The fans keep the LEDs cool and keep the electronics cool too

Without the fans working efficiently and dust free, the fixtures will fail and that will be a lot more costly

than having someone vacuum the fixtures on a regular basis

How often should the fans be cleaned? It depends on where the fixtures are; in a very dusty atmosphere

once a week So check the fan on a regular basis, it may not need cleaned every week but a quick “visual

inspection” should be done

The clear front plastic cover for the lenses should be cleaned so the light output is maintained With the

ElektraLite WW turned off, use only a moist lint-free cloth, and clean the plastic cover Never use alcohol

or solvents to clean the fixture Never spray anything onto the fixture at the front or in any place on the

fixture

7. Technical Specification.

Operating voltage 100 – 250v

Frequency 50 – 60 Hertz

18 leds

80 VI

Fan cooled

162 5mm x 162 5mm x 218 5mm

6 5" x 6 5" x 8 6"

2 1 kgs

4 6 pounds

ElektraLite is a division of Group One. Group One and its divisions are constantly improving their

product range and we reserve the right to make changes without prior notice.

8. Other Products.

For other great products that are manufactured under the ElektraLite product line,

please go to the website at www myElektraLite com

A preview of the products include:-

ElektraLite ML602

Tabla de contenidos

Otros manuales de Foco de elektraLite

elektraLite

elektraLite eyeBall RGBWA Manual de usuario

elektraLite

elektraLite eyeBall RGBWA Manual de usuario

elektraLite

elektraLite Mini Stingray Variable White Manual de usuario

Manuales populares de Foco de otras marcas

VIZULO

VIZULO Micro Martin Guía del usuario

EuroLite

EuroLite LED IP FL-100 SMD Manual de usuario

Cooper Wheelock

Cooper Wheelock XB12 Manual de usuario

Allen + Roth

Allen + Roth 17624-000 Manual de usuario

ADJ

ADJ 4 STAGE PAK Manual de usuario

Cooper Lighting

Cooper Lighting EGL91SW233 Manual de usuario

Max

Max 37496 Manual de usuario

BEGA

BEGA 85 143 Manual de usuario

Beamz

Beamz 151.226 Manual de usuario

EuroLite

EuroLite LED IP FL-8 Manual de usuario

Ledj

Ledj PERFORMER 36 RGB Manual de usuario

Perel

Perel ELS3 Manual de usuario

Perel

Perel ELS3WD Manual de usuario

LumX

LumX LM 36130 Manual de usuario

Xtricity

Xtricity 4-80053 Manual de usuario

Stahl

Stahl 6521/4 Series Manual de usuario

Ecosense

Ecosense EcoSpec Manual de usuario

Ayrton

Ayrton minipanel FX Manual de usuario

elektraLite eyeBall Manual de usuario

Manuales populares de Foco de otras marcas