Electra Roman Blinds Hoja de instrucciones
How to install,
programme and
operate your blind
electrablinds.co.uk
Electra
Roman
Blinds
Ref 09/20
Contents
The contents of your order
Blind fitting and position
Roman Blind Installation and removal
Battery pack installation & power up
Power up & testing -
without a control
Operation
Adjusting the upper & lower stop positions
Add/delete controls
Multi channel programming
Reset and reprogramme procedure
General Maintenance & Cleaning
Charging & troubleshooting -Page 15
-Page 14
-Page 12-13
-Page 11
-Page 10
-Page 9
-Page 8
-Page 7
-Page 6
-Page 5
-Page 4
-Page 3
Power supply
Rechargeable Li-ion Battery
Pack
The contents of your order
Each blind ordered will have
the following components:
Battery charger (if ordered)
3
Roman Blind Controls
If you ordered a control with
your blind(s), then it will be
one of the following:
Smart Home Options
If you ordered one of our
smart home options with
your blind(s), then it will be
one of the following:
Blind up to 1.2m wide:
2 brackets
Blind > 1.2m up to
1.8M wide: 3 brackets
Blind over 1.8m wide:
4 brackets
2 x raw plugs + screws
per bracket.
5-Channel
Wall Switch
Single-Channel
4-channel Wall Switch
Light sensor
Light &
temperature
sensor
1-channel or
6-channel
timer
Connexoon
hub for
app
control
Set of brackets
Fitting your blind inside the window recess
Firstly decide whether to face fix or top fix your blind.
We recommend you top fix your blind within the recess if:
•you have uPVC window frame
•there are obstructions like handles
We recommend you face fix your blind if:
•you want to fit the brackets directly to the window
frame
When deciding on the position the brackets, make sure that you allow enough space for the blind to clear window
handles while the blind is travelling down.
Fitting your blind outside the window recess
Follow the measurement steps below to centre your Roman blind in the
middle of your window:
To work out C:
1) Measure the width of the window (measurement B).
Write down the measurement.
2) Measure the width of the blind (measurement A).
Write down the measurement.
3) Take measurement B away from measurement A
and divide the answer by 2 to get measurement C.
BCC
Blind fitting & position
A
4
Roman blind installation
Bracket fitting options
The brackets can be fitted in the following ways:
Marking the bracket positions
Position the brackets in
place at the correct position
for the blind and mark
the fixing points per
bracket.
Marking/drilling the bracket positions
Fix the brackets in using suitable
fixings.
Mounting the Roman blind
While tilting the blind headrail at
a slight angle, locate the fabric
side horizontal groove that runs
along the top section of the
headrail into the front hook of
the bracket (fig 1).
Push the front of the headrail in
to compress the bracket springs
and rotate the headrail up to
locate the horizontal groove
situated at the rear of the
headrail until it clicks into place
(fig 2).
Allow the spring to release and
secure the headrail in place.
Removing the blind - Start at one end of the blind and:
1) Push the headrail in to compress the bracket spring.
2) Tilt the headrail down at the rear and unhook the headrail
from the rear secction of the bracket.
3) Repeat ensuring that the headrail is adequately supported.
5
Electra Top Tip!
If securing the brackets to plaster,
stone, brick, etc., drill the holes at the marked
positions using a 5.5mm masonry drill bit, then use
the wall plugs and screws supplied to fix the brackets.
Battery pack installation
6
7
Decide where you want the battery to sit and check that the battery is close enough to connect to the motor
supply cable. Position and mark the square mounting clips. Fix using the screws provided and suitable fixings.
Push the external battery into mounted clips.
Power up & testing
Before we dispatch your blind, we test it to ensure it's operating correctly. We also set the upper and lower stop
positions based on your individual window height measurement.
Lastly, your remote control
or wall switch will be
paired
to your motor so you're ready to go!
Once your blind is fixed securely in place, you
are ready to connect your battery pack to
your blind.
Take the motor supply cable and connect the
long plug into the long socket of the battery
pack. You can then tuck any excess cables
away behind the blind.
If you didn't order a control with your blind follow
the instructions on the next page
If you didn't order a control with your blind follow
the instructions on the next page.
If you ordered a control with your blind
follow the operation instructions on page 8.
7
Power up & testing-
blind supplied without a control
New blind - Existing Remote control/wall switch
Before you begin
The following instructions are relevant if you already have a remote control/wall switch and selected 'no control needed'
when ordering your Electra blind. The blind supplied has been set up with the up and down stop position preset for your
convenience.
Pairing your remote control/wall switch to your blind
STEP 1: Initiate programming.
Press both up and down
buttons together briefly and
let go - the blind will "jiggle".
A jiggle is a brief up and down
motion
.
STEP 2: Pair the control. Press
and hold the programming
button* on the back of the
your handset or wall switch
until the blind jiggles. Your
control is now paired to the
blind motor.
Electra Top Tip!
If you have
a 5 channel
handset, make sure
you select the channel
the blind is to operate
in before pressing the
program button.
*How to locate the programming button on your
control:
Single
channel
and 5-
channel
remote
Wall
switch
General control
We have programmed your blind to automatically stop at preset upper and lower stop positions. It couldn't be simpler- just
press the Up or Down button until the blind starts moving and your blind will move in the respective direction until it reaches
the preset stop position, where it will stop automatically. You can stop the blind at any point between the preset stop positions
by pressing the middle ‘my’ button.
Lowering the blind
Press the down button briefly to
send the blind to the lower stop
position.
Raising the blind
Press the up button briefly to
send the blind to the upper stop
position.
Stopping the blind
Press the 'My' button briefly to
stop the blind at an intermediate
position.
8
Operation
Operating your Roman Blind
Adjusting the upper & lower stop positions
2. Press and hold the
Up and Down buttons
until the blind jiggles.
3. Adjust to the desired
upper/lower stop
position using either
the Up or Down button.
4. Press and hold the
'my' button until the
blind jiggles.
1a. Adjust upper stop position -
press the up button and send the
blind to the current upper stop
position.
1b. Adjust lower stop position -
press the down button and send
the blind to the current lower stop
position.
9
Setting
Use either Up or Down to operate the blind and press 'my' to stop
at the desired intermediate position.
Once the desired intermediate position is reached, press and hold
the 'my' button until the blind jiggles (approx 5 secs). The 'my'
position has now been set.
Using the 'my' position
Send the blind to the 'my' position by pressing
'my' from ANY position (the blind must be
stationary prior to activating the 'my' position
function).
Delete the ‘my’ position
Send the blind to the 'my' position, then press
and hold 'my' until the blind jiggles (approx. 5
secs). The 'my' position has now been deleted.
Using the ‘my’ position (intermediate position)
The 'my' position is a memorised intermediate position between the
upper and lower stop positions. You can set this anywhere you want and
send the blind to it at the touch of the 'my' button.
14 10
Step 1 - Take a handset or wall
switch that is already
programmed to the blind
motor.
Step 2 - Press and hold the
program button of the
handset or wall switch until
the blind jiggles (approx
2-3 secs).
Step 3 - Press the program
button again to unpair the
control.
Add/delete controls
Delete a control
Control already paired to the
blind
Add a control
Control to add to the blind
memory
Step 1 - Press the program
button on your handset or
wall switch that already
controls the blind for about
2 seconds until the blind
jiggles. If using a 4 channel
handset, make sure you
have the right channel
selected.
Step 2- Press and hold the
program button of the new
handset or wall switch until
the blind jiggles (approx 1
sec).
Or Or
Tabla de contenidos
Otros manuales de Persiana de ventana de Electra
Manuales populares de Persiana de ventana de otras marcas
Domondo
Domondo PureNight Manual de instrucciones de instalación
rollease acmeda
rollease acmeda Easy Spring Air Guía de configuración
IKEA
IKEA KADRILJ Manual de usuario
Hallis Hudson
Hallis Hudson Rolls Super glide Manual de usuario
Benthin
Benthin P1614 Manual de usuario
MV LINE
MV LINE CLARA 015 Manual de instrucciones
