Electra Roller Hoja de instrucciones
electrablinds.co.uk
Electra Roller and
XL Roller blinds
How to install,
programme and
operate your blind
Ref 11/18
Contents
The contents of your order
Battery Pack installation
Uncassetted Roller Blind Installation
Cassetted Roller Blind installation
Power up & testing - with a control
Power up & testing - without a control
Operation
Adjusting the upper & lower stop positions
Reset and reprogramme procedure
Add/delete controls
Multi channel programming
-Page 3
-Page 4
-Page 5
-Page 6-7
-Page 8
-Page 9
-Page 10
-Page 11
-Page 12-13
-Page 14
-Page 15
Uncassetted roller blind
2 x Fixing
brackets
complete with
fixings
Power supply
Rechargeable Battery Pack
The contents of your order
Each blind ordered will have
the following components:
Each blind ordered will have the
following components:
Rechargeable battery tube
complete with fixings + 10 x
AA NiMH rechargeable
batteries + 2 x mounting clips
Battery Charger
(if ordered)
Controls
If you ordered a control
with your blind(s), then
it will be one of the
following:
Four-Channel
3
Roller
cassette clips
complete with
fixings
Wall
Switch
Cassetted roller blind
Single-Channel
4
Battery pack Installation
Step 1: Fit the clips for your battery pack using
suitable fixings.
The battery pack is supplied with screws and wall
plugs suitable for fixing to a solid brick or block wall.
If you have ordered a blind that fits inside the
recess, fit your battery pack close to the window
frame at the back of the recess.
Please note: If the width of your window recess is
less than 55cm, your battery pack will need to be
fitted vertically inside the recess or external to the
reveal.
If you have ordered a blind that fits outside the
recess ('Exact'), fit your battery pack at the front of
the recess.
Once the clips are in place, mount the battery pack
ensuring that the supply cable is pointed towards
the blind motor position (middle of the blind).
STEP 1- Marking the bracket positions
Remember when positioning your blind to make sure the fabric will clear any window handles or obstructions. Slide
the brackets into each end of the blind, then position the blind where you’d like to fix it in your window. Make a pencil
mark in the positions of the 2 fixing holes per bracket for drilling. We recommend using a spirit level as shown below
to ensure the blind is fitted level .
If your battery pack is fixed behind your blind, don't forget to leave enough space to
easily remove it for charging.
Uncassetted Roller Blind Installation
Electra Top Tip!
If securing the brackets to
plaster, stone, brick, etc.,
drill the holes at the
marked positions using a
5.5mm masonry drill bit,
then use the
wall plugs
and screws supplied to fix
the brackets.
STEP 2- Fitting the brackets
Secure the brackets in place at the marks previously made using suitable fixings.
5
Face-Fix
Top-Fix
STEP 3- Mounting the Roller Blind
Hold the blind to the brackets with the fabric
hanging from the back of the blind and the
motor head aerial hanging vertically down
(pointing towards the floor). Slide the motor end
into its bracket first, then slide the opposing end
into its bracket as per the diagram. Make sure
the release lever is to the front for easy access.
Then slide the bracket covers on.
STEP 4 - Power up & Testing- go to page 8
Before fitting the uncassetted blind, we recommend you install the battery - see page 4 for guidance.
STEP 1 - Remember when positioning your blind to make sure the fabric will clear any window handles or obstructions. If
your blind is outside the recess it will require a face-fix - position your bracket a minimum distance of 3.2cm from the ceiling.
For inside the recess it will be a top-fix - position your bracket a minimum of 3.5cm from the battery pack mounting clips.
Top-fix
(inside
recess)
Cassetted Roller Blind Installation
Before fitting the cassetted
blind, we recommend you install the battery pack- see page
4
for guidance.
6
STEP 2- Fixing positions
Secure the clips in place
using suitable fixings.
STEP 1- Clip spacing
Mark the clips approx
10cm in from each
end with the other
clips spaced evenly
between them.
Electra Top Tip!
If securing the brackets to
plaster, stone, brick, etc.,
drill the holes at the
marked positions using a
5.5mm masonry drill bit,
then use the wall plugs
and screws supplied to fix
the brackets.
Face-Fix
(outside
recess)
7
STEP 3- Fitting
Place the front lip of your cassette into the front
hook of the clip and push upwards into the clip
until there is a firm 'click'.
Note: Diagrams show face-fix. For top-fix use the
grooves on the top of the cassette.
Removing
If you need to remove the blind,
lever the lip of the clip at the back
of the cassette using the head of a
screwdriver.
Cassetted Roller Blind Installation continued
[Diagram shows face-fix]
STEP 4 - Power up & Testing. Go to Page 8.
8
Power up & testing -
blind supplied with a control
Before we dispatch your blind, we test it to ensure it's operating correctly. We also set the upper and lower
stop positions based on your individual window height measurement.
Lastly, your remote control
or wall
switch will be paired
to your motor so you're ready to go!
Once your blind is fixed securely in place,
you are ready to connect the battery pack.
Take the motor supply cable and connect
the long plug into the long socket of the
battery pack. You can then tuck any excess
cables away behind the blind.
If you ordered a control with your blind follow
the instructions on page 10.
If you didn't order a control with your blind
follow the instructions on the next page.
Power up & testing-
blind supplied without a control
New blind - Existing Remote control/wall switch
Before you begin
The following instructions are relevant if you already have a remote control/wall switch and selected 'no control needed'
when ordering your Electra blind. The blind supplied has been set up with the up and down stop position preset for your
convenience.
Pairing your remote control/wall switch to your blind
STEP 1: Initiate programming.
Press both up and down
buttons together briefly and
let go - the blind will "jiggle".
A jiggle is a brief up and down
motion
.
STEP 2: Pair the control. Press
and hold the programming
button* on the back of the your
handset or wall switch until the
blind jiggles. Your control is
now paired to the blind motor.
Electra Top Tip!
If you have a 4 channel
handset, make sure
you select the channel
the blind is to operate
in before pressing the
programme button.
*How to locate the programming button on your
control:
Single
channel
and 4-
remote
Wall
switch
9
channel
10
Operation
General control
We have programmed your roller blind to automatically stop at preset upper and lower stop positions. It couldn't be simpler- just
press the Up or Down button until the blind starts moving and your blind will move in the respective direction until it reaches the
preset stop position, where it will stop automatically. You can stop the blind at any point between the preset stop positions by
pressing the middle ‘my’ button.
Lowering the blind
Press the down button briefly to
send the blind to the lower stop
position.
Raising the blind
Press the up button briefly to
send the blind to the upper stop
position.
Stopping the blind
Press the 'My' button briefly to
stop the blind at an intermediate
position.
Operating your Roller Blind
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Persiana de ventana de Electra
Manuales populares de Persiana de ventana de otras marcas
Domondo
Domondo PureNight Manual de instrucciones de instalación
rollease acmeda
rollease acmeda Easy Spring Air Guía de configuración
IKEA
IKEA KADRILJ Manual de usuario
Hallis Hudson
Hallis Hudson Rolls Super glide Manual de usuario
Benthin
Benthin P1614 Manual de usuario
MV LINE
MV LINE CLARA 015 Manual de instrucciones
