Eldes ESIM252 Manual de usuario

ESIM252

GSM CONTROL SYSTEM

EN ESIM252 User Manual v2.1

User Manual v2.1

Valid for ESIM252 v21.04.00 and up

SAFETY INSTRUCTIONS

Please read and follow these safety guidelines to safeguard yourself and others:

• GSM control system ESIM252 (later referred to as “the system” or “ the device”) contains a built-in radio transceiver operating in GSM

850/900/1800/1900 MHz bands.

• DO NOT use the system where it can cause potential danger and interfere with other devices – such as medical devices.

• DO NOT use the system in hazardous environment.

• DO NOT expose the system to high humidity, chemical environment or mechanical impact.

• DO NOT attempt to repair the system yourself – any repairs must be carried out by fully qualied personnel only.

Disconnect the mains power before installing. Never install or carry out maintenance during stormy weather. The electric

socket that powers the system must be easily accessible.

Please use the 10-24V 50Hz ~200mA AC or 10-24V 200mA DC power supply unit

that meets the EN 60950-1 standard. Any additional device you connect to the system,

such as a computer, must also be powered by an EN 60950-1 approved supply. When con-

necting the power supply to the system, switching the polarity terminal places does not

have any aect.

Phase

AC 230V

50 Hz/DC 24V

USB cable

Null

ESIM252

AC/DC

External power supply can be connected to AC mains only inside installation room with automatic 2-pole circuit breaker ca-

pable of disconnecting circuit in the event of short circuit or over-current condition. Open circuit breaker must have a gap be-

tween connections of more than 3mm (0.12in) and the disconnection current 5A.

To switch the system o, unplug the external electric power supply from or any other linked device that the system is powered

from

A blown fuse cannot be replaced by the user. The replacement fuse has to be of the kind indicated by the manufacturer (fuse

F1 model – MINISMDC050F 0.5A).

The WEEE (Waste Electrical and Electronic Equipment) symbol on this product (see left) means it must not be disposed of in

household waste. To prevent possible harm to human health and/or the environment, you must dispose of this product in an

approved and environmentally safe recycling facility. For further information contact your system supplier, or your local waste

authority.

ESIM252 User Manual v2.1

CONTENTS

1. GENERAL INFORMATION .........................................................................................................................................................5

2. TECHNICAL SPECIFICATIONS...................................................................................................................................................5

2.1. Electrical and Mechanical Characteristics..................................................................................................................................................... 5

2.2. Main Unit, LED Indicator and Connector Functionality ...............................................................................................................................6

2.3. Wiring Diagram ..................................................................................................................................................................................................7

3. INSTALLATION .........................................................................................................................................................................8

4. GENERAL OPERATIONAL DESCRIPTION..................................................................................................................................9

5. CONFIGURATION METHODS ....................................................................................................................................................9

5.1. SMS Text Messages...........................................................................................................................................................................................9

5.2. ELDES Conguration Tool ................................................................................................................................................................................9

6. SYSTEM LANGUAGE ...............................................................................................................................................................10

7. SMS PASSWORD.....................................................................................................................................................................10

8. USER PHONE NUMBERS ........................................................................................................................................................11

8.1. System Control from any Phone Number....................................................................................................................................................12

9. DATE AND TIME......................................................................................................................................................................13

10. INPUTS ...................................................................................................................................................................................13

10.1. Pulse Counter...................................................................................................................................................................................................14

10.2. Disabling and Enabling Inputs.......................................................................................................................................................................14

11. ALARM/RESTORE NOTIFICATIONS........................................................................................................................................16

11.1. Enabling and Disabling Alarm/Restore Notication Delivery to All Listed Users ................................................................................19

12. AUDIO FILES .......................................................................................................................................................................... 20

13. OUTPUTS............................................................................................................................................................................... 20

13.1. Output Names................................................................................................................................................................................................. 20

13.2. Output Control by Free of Charge Phone Call .............................................................................................................................................21

13.3. Control by SMS Text Message....................................................................................................................................................................... 24

13.4. Automatic Output Control............................................................................................................................................................................. 26

14. SYSTEM INFORMATION. INFO SMS....................................................................................................................................... 29

14.1. Periodic Info SMS............................................................................................................................................................................................ 29

15. SYSTEM NOTIFICATIONS ...................................................................................................................................................... 30

15.1. SMSC (Short Message Service Center) Phone Number............................................................................................................................ 30

16. EVENT LOG .............................................................................................................................................................................31

17. REMOTE LISTENING ...............................................................................................................................................................32

18. GPRS NETWORK SETTINGS ...................................................................................................................................................32

19. MONITORING STATION...........................................................................................................................................................33

19.1. Data Messages - Events .................................................................................................................................................................................33

19.2. Communication................................................................................................................................................................................................33

20. PROJECT EXAMPLES AND CONFIGURATION..........................................................................................................................37

20.1. Using in Enterprises........................................................................................................................................................................................37

20.2. Using in a Private House ............................................................................................................................................................................... 41

20.3. Using with Heating System and Flood Detector....................................................................................................................................... 43

20.4. Using for Breakdown Reports ...................................................................................................................................................................... 45

21. TECHNICAL SUPPORT ........................................................................................................................................................... 48

21.1. Troubleshooting ............................................................................................................................................................................................. 48

21.2. Restoring Default Parameters ..................................................................................................................................................................... 48

21.3. Updating the Firmware via USB Cable ........................................................................................................................................................ 48

21.4. Updating the Firmware via GPRS Connection Remotely ......................................................................................................................... 49

22. RELATED PRODUCTS............................................................................................................................................................. 50

EN ESIM252 User Manual v2.1

It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced written au-

thorization from “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a

warning. Hereby, “ELDES UAB” declares that the GSM control system ESIM252 is in compliance with the essential requirements and

other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt.

Limited Liability

The buyer agrees that the system will reduce the risk of re, theft, burglary or other danger but that it does not guarantee against the oc-

currence of such events. “ELDES UAB” will not take any responsibility for the loss of personal eects, property or revenue whilst using the

system. The liability of “ELDES UAB” is limited to the value of the system purchased. “ELDES UAB” is not aliated with any mobile/wireless/

cellular provider and is therefore not responsible for the quality of such services.

Manufacturer Warranty

The system carries a 24-month manufacturer warranty from “ELDES UAB”. The warranty begins the day the system is purchased by the

user and the receipt must be retained as proof of purchase date. The warranty remains valid only if the system is used as intended, fol-

lowing all guidelines outlined in this manual and in accordance with the operating conditions specied. The warranty is void if the system

has been exposed to mechanical impact, chemicals, high humidity, uids, corrosive and hazardous environments or force majeure factors.

Dear Customer,

Thank you for choosing to purchase the GSM control system ESIM252. Your thoughtful decision will ensure reliable solution for many

years as all ELDES products are manufactured to meet the highest standards.

We are condent that you will be completely satised with your product. However, in the unlikely event that you do experience a prob-

lem, please contact the dealer from whom you made your purchase.

UAB ELDES

www.eldes.lt

CONTENTS OF PACK

Item Quantity

1. ESIM252...................................................1

2. User manual............................................1

3. GSM/GPRS antenna ...............................1

4. Plastic standos....................................4

Not included:

• SIM card – we recommend you get a contract SIM, not Pay As You Go.

• miniUSB cable – can be obtained from your local distributor.

• Microphone – can be obtained from your local distributor.

ESIM252 User Manual v2.1

1. GENERAL INFORMATION

ESIM252 is a micro-controller based device intended to receive alarm/restore events by SMS text message or phone call and control an

electrical appliance via the GSM network.

Examples of using the system:

• Access control.

• Gate control of private houses.

• Notication of system events, such as arming/disarming, alarm/restore from non-GSM alarm system.

• Non-GSM alarm system arming/disarming by SMS text message.

• Any electrical appliance control: lighting, watering, heating etc.

• Remote reboot of the “frozen” systems, such as computer network or a server.

Main features:

• 5 inputs with customizable alarm/restore texts.

• Up to 5 user phone numbers for system conguration by SMS text messages, acceptance of input alarm/restore SMS text messages and

phone calls, output control by SMS text message and free of charge phone call.

• 2 relay outputs for electrical appliance control or non-GSM alarm system arming/disarming (key-switch).

• Manual output control by free of charge phone call.

• Automatic output control in accordance with the scheduled time.

• Up to 10 audio messages for input alarm/restore notication.

• Event log of 500 events.

• Periodic self-test notication by SMS text message to user phone number.

2.TECHNICAL SPECIFICATIONS

2.1. Electrical and Mechanical Characteristics

Supply voltage 10-24V 50Hz ~ 200mA max / 10-24V 200mA max

Current used in idle state Up to 50mA

GSM modem frequency 850/900/1800/1900 MHz

Number of outputs 2

Output type Relay; NO (normally-open)

Maximum commuting output values 24V 50Hz ~ 0,5A / 24V 1A

Number of “low” level (negative) inputs 4

Number of “high” level (positive) inputs 1

“Low” level (negative) input value range 0... 16V -0.8... -0.4mA

“High” level (positive) input value range 5... 50V 0.17 .... 1.7mA

“Low” level (negative) and “high” level (positive) input connection type NO (normally-open) / NC (normally-closed)

Dimensions 87x107x29mm (3.43x4.21x1.14in)

Operating temperature range -20…+55 °C (-30...+55 °C with limitations) (-4... +131°F (-22...

+131°F))

Humidity 0-90% RH @ 0... +40°C (0-90% RH @ +32... +104°F)

(non-condensing)

EN ESIM252 User Manual v2.1

2.2. Main Unit, LED Indicator and Connector Functionality

Z1Z2Z3Z4Z5COMRELAYAC/DC

G S M

MO DE M

ANT

MIC

SIM CARD

DEF

SIM STAT

NETW

USB

Z1Z2Z3Z4Z5COMRELAY2RELAY1AC/DC

G S M

MO DE M

ANT

MIC

SIM CARD

DEF

SIM STAT

NETW

USB

Main Unit Functionality

ANT GSM/GPRS antenna SMA type connector

USB Mini USB port

SIM CARD SIM card slot / holder

GSM MODEM GSM network 850/900/1800/1900 MHz

modem

MIC Microphone connector

SIM STAT Red light-emitting diode indicating SIM

card status

NETW Green light-emitting diode indicating GSM

signal strength

DEF Pins for restoring default settings

F1 0.5A fuse

Connector Functionality

AC/DC Power supply terminals

RELAY1 ESIM252 output C1 terminal

RELAY2 ESIM252 output C2 terminal

COM Common terminal

Z5 “Low” level (negative) input terminal

Z4 “Low” level (negative) input terminal

Z3 “Low” level (negative) input terminal

Z2 “High” level (positive) input terminal

Z1 “Low” level (negative) input terminal

LED Indicator Functionality

SIM STAT indication SIM card status

OFF No mains power / micro-controller

fault

Steady ON SIM card is attempting to connect

to the GSM network / SIM card is

not present / PIN code enabled

Flashing GSM connection failed

NETW indication GSM signal strength

OFF No GSM signal

Flashing every 1 sec. Poor

ESIM252 User Manual v2.1

2.3. Wiring Diagram

ELECTRICAL APPLIANCE

ESIM252

Z1Z2

Z3Z4Z5COMRELAY

POWER

SUPPLY

AC/DC

EN ESIM252 User Manual v2.1

3.INSTALLATION

• The system should be installed indoors, in stationary environment ONLY.

• For the connection of input/output terminals, use 0.50 mm2(0.02in2) thread unshielded cable of up to 100m (328.08ft) length.

1. Wire up the system in accordance with the wiring diagrams (see 2.3 Wiring Diagrams for more details).

2. Connect the GSM/GPRS antenna. Based on the type of the GSM/GPRS antenna supplied with ESIM252 unit, follow the recommendations

for the antenna installation:

GSM/GPRS

antena

Never install in the following

locations:

• inside the metal cabinet

• closer than 20cm (7.87in)

from the metal surface

and/or power lines

3. Disable the PIN code request of the SIM card by inserting it into a mobile phone and following the proper menu steps.

4. Once the PIN code is disabled, insert the SIM card into the SIM card slot / holder of ESIM252 system.

5. Ower up the system and wait until indicator SIM STAT lights up indicating SIM card status.

6. Once the indicator SIM STAT lights OFF, the illuminated indicator NETW lights up indicating that the system has successfully connected

to the GSM network. To nd the strongest GSM signal, position the GSM/GPRS antenna and follow the indications provided by NETW

indicator (see 2.2. Main Unit, LED Indicator & Connector Functionality for more details).

7. Change the system language if necessary (see 6. SYSTEM LANGUAGE for more details).

8. Change the default SMS password (see 7. SMS PASSWORD for more details).

9. Set the phone number for User 1 (see 8. USER PHONE NUMBERS for more details).

10.Set system date and time (see 9. DATE AND TIME for more details).

11. Once the system is fully congured, it is ready for use. However, if you fail to receive a reply by SMS text message from the system,

please check the SMSC (Short Message Service Center) phone number. For more details regarding the SMS center phone number, please

refer to 15.1. SMSC (Short Message Service Center) Phone Number.

ATTENTION: The system is NOT compatible with pure 3G SIM cards. Only 2G/GSM SIM cards and 3G SIM cards with 2G/GSM prole

enabled are supported. For more details, please contact your GSM operator.

ATTENTION: We also recommend you to disable call forwarding, voice mail/text message reports on missed/busy calls (“call

catcher”) and similar services that might cause incorrect system operation. Please contact your GSM operator for more details on these

services and how to disable them.

NOTE: For maximum system reliability we recommend you do NOT use a Pay As You Go SIM card. Otherwise, in the event of insucient

credit balance on the SIM card, the system would fail to make a phone call or send SMS text messages.

NOTE: We advise you to choose the same GSM SIM provider for your system as for your mobile phone. This will ensure the fastest, most

reliable SMS text message delivery service and phone call connection.

NOTE: The system is NOT compatible with pure 3G SIM cards. Only 2G/GSM SIM cards and 3G SIM cards with 2G/GSM prole enabled are

supported. For more details, please contact your GSM operator.

ESIM252 User Manual v2.1

4.GENERAL OPERATIONAL DESCRIPTION

GSM control system ESIM252 uses the GSM network for event transmission by SMS text message. When one of the 5 available listed num-

bers dials the system, it answers the call and the user can listen to a pre-recorded audio message and hear what is going on in the premises

once the audio message is over. The remote listening function operates only when a microphone is connected. When the “conversation” is

over, the user The system will ignore SMS requests and phone calls coming from non-listed phone numbers.

The system has 5 digital inputs (normally closed or normally open) for alarm system’s PGM output or detection device connection, such as

magnetic door contact. By connecting the input to the non-GSM alarm system’s PGM output, the user will be able to receive an SMS text

message or phone call regarding system alarm/restore, arming/disarming and other events depending on the alarm system conguration.

In addition to being informed by SMS text message or phone call regarding alarm and restore events of the inputs, the users can control

one electrical appliance by connecting it to the relay outputs. For example, users can turn ON or OFF the heating, lighting, lift the gates,

blinds etc. The output can also be used for arming/disarming by connecting it to one of the alarm system zones congured as a key-switch.

5.CONFIGURATION METHODS

5.1. SMS Text Messages

In this user manual the underscore character ”_” represents one space character. Every underscore character must be

replaced by a single space character. There must be no spaces or other unnecessary characters at the beginning and at the

end of the SMS text message.

SMS

In order to configure and control the system by SMS text message, send the text command to the ESIM252 system phone

number from one of the listed user phone numbers. The structure of SMS text message consists of 4-digit SMS password (the

default SMS password is 0000 – four zeros), the parameter and value. For some parameters the value does not apply e. g.

STATUS. The variables are indicated in lower-case letters, while a valid parameter value range is indicated in brackets.

5.2. ELDES Conguration Tool

Software ELDES Conguration Tool is intended for ESIM252 GSM control system conguration locally via USB port or remotely via GPRS

network connection. This software simplies system conguration process by allowing to use a personal computer in the process. Before

starting to use ELDES Conguration Tool software, please read the user guide provided in the software’s HELP section.

ELDES Conguration Tool is freeware and can be downloaded from at: www.eldes.lt

NOTE: ELDES Conguration Tool software is secured with SMS password. The default SMS password is 0000 (see 7. SMS PASSWORD).

5.2.1.Remote Connection

ATTENTION: The system will NOT send any data to the monitoring station while remote conguration is in progress. However, dur-

ing the remote conguration session the data messages will be queued up and transmitted to the monitoring station after the remote

conguration session is over.

ELDES Conguration Tool software provides remote system conguration ability via Internet using one of the following methods:

• ELDES proxy server (recommended). The connection can be established on the system via GPRS network.

• Running TCP/IP server on ELDES Conguration Tool (advanced). The connection can be established on the system via GPRS network.

In order to start using the remote conguration feature, please run the step-by-step wizard and follow the steps provided in the start page

of ELDES Conguration Tool software. Please, note that it will be necessary to send an SMS text message to the system’s phone number

in order to initiate the remote connection. By following the steps you will be instructed on what text must be sent to the system’s phone

number in such case.

5.2.2. Ending the Remote Connection Session

After the system conguration is complete, use one of the following methods to end the conguration process:

• Click Disconnect or Stop button and close ELDES Conguration Tool software;

• The session will automatically expire in 20 minutes. Before the last 5 minutes, the software will oer the user to extend the session for

another 20 minutes.

• Alternatively, the connection with the server can be terminated at any time by sending an SMS text message.

Terminate the

connection

SMS text message content:

ssss_ENDCONFIG

Value: ssss – 4-digit SMS password.

Example: 1111_ENDCONFIG

Once the session is expired or terminated, the system will reply with an SMS text message conrming the end of the session.

EN ESIM252 User Manual v2.1

6.SYSTEM LANGUAGE

The system comes equipped with a multiple languages for communication with the user by SMS text messages. The default system lan-

guage depends on the rmware, which is based on the customer’s location.

List of currently available system languages:

• English

• Lithuanian

• Slovak

Set system language SMS

SMS text message content:

Value: LN – language index; range – [EN – English,, LT – Lithuanian, SK – Slovak].

Example: LT

Cong

Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.

NOTE: To change the language once the system has already been congured, you need to reset the device to the default conguration.

For more details on how to do this, please refer to 21.2. Restoring Default Parameters.

7.SMS PASSWORD

For security reasons, the system uses the following type of password:

SMS password – 4-digit password used for system conguration and control from user phone number by SMS text messages and logging

in to ELDES Conguration Tool software. By default, SMS password is 0000, which MUST be changed!

Set SMS password SMS

SMS text message content:

wwww_PSW_ssss

Value: wwww – 4-digit default SMS password; ssss – 4-digit new SMS password; range –

[0001... 9999].

Example: 0000_PSW_1111

Cong

Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.

NOTE: The system rejects the SMS text messages containing wrong SMS password even from a listed user phone number.

Otros manuales para ESIM252

Tabla de contenidos

Otros manuales de Receptor de Eldes

Eldes

Eldes ESR100 Manual de usuario

Eldes

Eldes EWT1 Manual de usuario

Eldes

Eldes ESR100 Manual de usuario

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario