Eldes ET07 Manual de usuario

It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced written authorization from “ELDES

UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby, ELDES UAB declares that this

COMMUNICATOR ET07 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of confor-

mity may be consulted at www.eldes.lt/ce.

User Manual v1.0

Safety instructions

Please read and follow these safety guidelines in order to maintain safety of operators and people around:

• GSM communicator ET07 (further referenced as system) contains a radio transceiver operating in GSM900 and GSM1800 bands.

• Don’t use the system where it can interfere with other devices and cause any potential danger.

• Don’t use the system with medical devices if this is required in the manual of the medical device.

• Don’t use the system in hazardous environment.

• Don’t expose the system to high humidity, chemical environment or mechanical impacts.

• Don’t attempt to personally repair the system.

• System labelling sticker is at the bottom of the device.

System ET07 is a device mounted in limited access areas. Any system repairs must be done only by qualied, safety aware

personnel.

Mains power must be disconnected before any installation or tuning work starts. The system installation or maintenance

must not be done during stormy conditions.

The system must be powered by main 11-24V 50Hz ~300mA AC or 11-24V --- 300mA DC power supply which must be appro-

ved by LST EN 60950-1 standard and be easily accessible.

Any additional devices linked to the system ET07 (computer, alarm control panel etc.) must be approved by LST EN 60950-1

standard.

External power supply can be connected to AC mains only inside

installation room with automatic 2-pole circuit breaker capable of

disconnecting circuit in the event of short circuit or over-current con-

dition. Open circuit breaker must have a gap between connections of

more than 3mm.

Fuse F1 type 5x20 mm 3A Slow blown. Blown fuse cannot be replaced by the user and the replacement fuses have to be

exactly the same as indicated by the manufacturer.

The device is fully turned o by disconnecting 2-pole switch o device of the external power supply or any other linked

device that the system ET07 is powered from.

The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that in the EU

the product must not be disposed of together with household waste.

Phase

AC 230V

50 Hz/DC 24V

USB cable

Null

Grounding

ET07

Limited Liability

The buyer must agree that the system will redu-

ce the risk of re, theft, burglary or other dangers

but does not guarantee against such events. “EL-

DES UAB” will not take any responsibility regarding

personal, property or revenue loss while using the

system. “ELDES UAB” responsibility according to

local laws does not exceed value of the purchased

system. “ELDES UAB” is not aliated with GSM ope-

rators providing cellular services, therefore is not

responsible for network services, coverage or its

operation.

Manufacturer Warranty

The system carries a 24-month warranty by the

manufacturer “ELDES UAB”.

Warranty period starts from the day the system

has been purchased by the end user. The warranty

is valid only if the system has been used as inten-

ded, following all guidelines listed in the manual

and within specied operating conditions. Receipt

with purchase date must be kept as a proof.

The warranty is voided if the system has been

exposed to mechanical impacts, chemicals, high

humidity, uids, corrosive and hazardous environ-

ment or other force majeure factors.

Package Content

1. System ET07 ............................................................1 pcs

2. ET07 user manual .................................................1 pcs

3. GSM antenna ..........................................................1 pcs

CONTENT

1 General Information

1.1 Function............................................................................................ ...........12

1.2 Operation Description............................................................................. 12

1.3 Technical Specications.......................................................................... 12

1.4 Connection Circuit ...................................................................................13

1.5 Connectors and LED Indicators Functionality ................................13

1.6 System Installation ...................................................................................14

1.7 Light Emitting Indicators Functionality ............................................ 15

2. System Pre-operation

2.1 Informing Security Service Mode ....................................................... 16

2.2 Informing Users via SMS Messages Mode .......................................16

2.3 Informing Security Service and Users Mode ...................................16

3. Appendix

3.1 Restoring Factory Default Parameters................................................ 17

3.2 ET07 Conguration Program........................................................... .....17

3.3 Technical Support.......................................................................... ...........17

About User Manual. Quick Start.

This document describes remote informing system ET07, its operation and installation. It is very important to read User Manual before

start using the system. A quick start guide is located in rst two chapters.

1. General Information

1.1 Function

Communicator ET07 is for transferring information from the Alarm Control Panel to the monitoring station via GSM audio con-

nection channel or/and users via SMS message.

The system van be used in the following applications:

• Property security

• To make and receive telephone calls via GSM audio connection channel

1.2 Operation Description

Communicator ET07 works over GSM network. The communicator transmits CONTACT ID and 4+2 protocol messages and fully

imitates telephone line. When dialling a number with a telephone or via Alarm Control Panel, tonal (DTMF) number dialling mode

must be enabled. The user can also call from communicator to the telephone.

Communicator ET07 can operate in 3 modes, i. e.:

1. transmits information from the Alarm Control Panel to the monitoring station via GSM audio connection signal;

2. transmits information from the Alarm Control Panel only to the registered users via SMS message;

3. transmits information from the Alarm Control Panel to the monitoring station via GSM audio connection signal as well as

to registered users via SMS message.

An additional computer program ET07 Conguration Tool is also used for congurations which are necessary for the system to

operate in the second and third modes, i. e., to send SMS messages to the registered users. The device is connected to the compu-

ter via USB or RS232 type connection (depending on which type of connection is implemented in the card – see g. 1).

1.3 Technical Specications

Electrical and Mechanical Specications

Supply voltage 11-24V 50 Hz ~ 300mA max ar 11-24V 300mA max

Current used in standby mode 70mA max

GSM modem frequency 900/1800/1900 MHz

Supported protocols CONTACT ID, 4+2

Maximum number of users to whom SMS messages are delivered 5

Dimensions 139x84 mm

Operating temperature range -20...+55oC

Generated phone line voltage 48 V

Generated phone line current 25 mA

Generated phone line impedance 600 Ohm

Ringing voltage of generated phone line ± 72 V (25 Hz)

Dial tone of generated phone line 350 Hz

USER MANUAL ELDES ET07 V1.0 13

FUSE

GSM MODEM

INFO

STATUS

GSM

RS232

USB

DEFAULT

MODE

SET

For congurations

PROG

SIM CARD

TEL LINE

RJ11

ANT

AC/DC

AUX

ALARM

CONTROL PANEL

RING/TIP

GSM antenna

Connection

for telephone

AC/DC

1.1/3.5mm

Power

Supply DC

1.4 Connection Circuit

1.5 Connectors and LED Indicators Functionality

Main Units

GSM MODEM GSM network 900/1800/1900 MHz modem

SIM CARD SIM card

ANT GSM antenna SMA type connector

FUSE 3A fuse

Connector Functionality

Labelling Explanation

AC/DC Power supply connection pins

AC/DC 1,1/3,5mm Alternative power supply connection pins. Connected in parallel with AC/DC connection. Internal diameter of

the plug is 1.1 mm, , external diameter of the plug is 3.5 mm

TEL LINE Pins connected to the Alarm Control Panel pins RING and TIP. Connected in parallel with RJ11 connection.

RJ11 RJ11 type connection for telephone. Connected in parallel with TEL LINE connection.

DEFAULT Connectors for restoring factory default settings

RS232 COM port connection

USB Mini USB port

SET Connectors for enabling the 3rd operation mode of the device

MODE Connectors for connecting the 2nd operation mode of the device

PROG Not used

Light Emitting Diodes LED

INFO Working mode indicator

STATUS Device activity indicator

GSM GSM network quality indicator

1.6 System Installation

NOTE

Due to GSM network characteristics it is recommended to use the system ET07 with the same GSM operator which is used by

system users. Thus you will ensure the quickest SMS message delivery and receipt.

NOTE

To ensure maximum system operation reliability we recommend do not use prepaid cards. If the balance is insucient the

system will not be able to inform users about the alarm.

IMPORTANT

Power supply at Alarm Control Panel must be disconnected before any installation or tuning work.

Device installation and Pre-operation:

1. Fasten the system in the box using fastening holders

2. Place SIM card in the holder but make sure that SIM card PIN code is disabled. (PIN code can be disabled by putting SIM card

into mobile phone and following proper menus). SIM card should not have any remaining SMS messages.

3. Connect the antenna (the device cannot be turned on without antenna).

4. Connect the circuit as shown in g. no. 2 – connect telephone line output of the Alarm Control Panel (RING/TIP) to TEL LINE

connectors of communicator ET07. In this case power supply is usually used as AUX output of Alarm Control Panel.

5. When AC power supply (ground transformer) is used, connect according to circuit no. 3. In this case you do not need to

connect any other power supplies.

6. The system should start in less than a minute. STATUS indicator should be blinking every ve seconds indicating connection

to GSM network. If the indicator is blinking very frequently, i. e., several times per second, it is possible that SIM card is inser-

ted incorrectly or PIN code request is not disabled.

The system can be installed only in a metal or non-ammable plastic box. When the metal box is also used as power supply

ground transformer it is necessary to ground the box using yellow/green colour cable. For the connection of ground 230V trans-

former use 3x0.75 mm2 1 thread double isolated cable. The initial winding of the ground transformer must be connected through

0.5A fuse. 230V power supply cables cannot be grouped with low voltage cable group. For the connection of power supply and

output connectors use 1 thread 2x0.75 mm2 cable. For the connection of input/output connectors use 0.50 mm2 1 thread cable.

Fig. No. 3Fig. No. 2

Fuse 500 mA

~230V 50Hz

AC/DC

~10-24V

TEL LINE AC/DC

AUXRING/TIP

ET07

Alarm Control Panel

USER MANUAL ELDES ET07 V1.0 15

1.7 Light Emitting Indicators Functionality

Connection Strength Indicator

To identify connection strength GSM indicator is used. To ensure the best quality of the network adjust the position of GSM

antenna and nd the best possible connection by watching the frequency of indicator blinking.

GSM indicator blinking Meaning

O No connection

Every 3 seconds The connection is not reliable

Every second Satisfactory

Several times per second Good

Indicator is lit Excellent

It is recommended to install the antenna remotely from communicator panel. Thus you will ensure better quality of audio

signal. We do not recommend installing the antenna in a metal box.

It is also used few others indicators – device activity indicator STATUS and working mode indicator INFO.

Device Activity Indication

STATUS indicator blinking Meaning

O No power supply or some fault is present

Blinking several times per second SIM card is used improperly/is not used

Indicator is lit The device is working properly and ready for use

Working Mode Indication

INFO indicator blinking Reikšmė

O The device is in passive mode

Blinking several times per second The device retransmits the data sent from Secu-

rity Control Panel to the panel of security service.

(this indication is possible then device is working

in rst mode)

Indicator is lit The device decodes the data sent via CONTACT

ID protocol to textual, user-understandable

information.

2. System Pre-operation

Communicator ET07 can operate in 3 modes:

1. Informing security service mode – transmits information from the Alarm Control Panel via GSM audio connection

signal only to security service panel;

2. Informing users via SMS messages mode – transmits information from the Alarm Control Panel via SMS messages only

to registered users;

3. Informing security service and user mode – transmits information from the Alarm Control Panel via GSM audio connec-

tion signal to security service panel as well as to registered users via SMS messages.

This chapter describes pre-operation and system operation when each of the above mentioned modes is enabled.

ATTENTION:

On the Alarm Control Panel you should enable tonal (DTMF) number dialling mode, activate CONTACT ID or 4+2 data transmis-

sion protocol and enter telephone number of security service panel.

ATTENTION:

It is also necessary to enter telephone number of security service on the Alarm Control Panel when you do not need to transmit

data to security service and you are using only SMS messaging mode. In such a case you can use any telephone number (you can

use the number consisting of one digit).

2.1 Informing Security Service Mode

If you want the device to operate in this operating mode you must ensure that all connectors in connec-

tor group SET-MODE-PROG are not short-circuited (jumper is not used).

When this mode is enabled communicator ET07 only retransmits data sent from Alarm Control Panel via

CONTACT ID or 4+2 protocol to security service panel via GSM audio connection channel. The device does

not require any additional congurations.

2.2 Informing Users via SMS Messages Mode

This operation mode is enabled by putting a jumper on MODE connectors in connector group SET-MO-

DE-PROG (as demonstrated in the example). Other connectors must not be short-circuited.

When this operation mode is used the information about the secured object is delivered only to user

(users) and security service is not informed. In this case the device decodes the data sent from the Alarm

Control Panel via CONTACT ID protocol to user-understandable text and sends it via SMS message. This

decoding is performed according to the preset parameters which can be specied by the user only by using

the program ET07 Conguration Tool (for more information please refer to user manual of this program). SMS

messages can be received by up to 5 users.

2.3 Informing Security Service and Users via SMS Messages Mode

This operation mode is enabled by putting a jumper on SET connectors in connector group SET-MODE-

PROG (as demonstrated in the example). Other connectors must not be short-circuited.

When this operation mode is used the information about the secured object is received by the user

(users) as well as security service. Device retransmits the data sent from the Alarm Control Panel via CON-

TACT ID protocol to the panel of security service and decodes this data to user-understandable text and

sends it via SMS message (indicator INFO informs only about decoding).The text is created by the user. This

decoding is performed according to the preset parameters which can be specied by the user only by using

the program ET07 Conguration Tool (for more information please refer to user manual of this program).

SMS messages can be received by up to 5 users.

SET

MODE

PROG

SET

MODE

PROG

SET

MODE

PROG

USER MANUAL ELDES ET07 V1.0 17

3. Appendix

3.1 Restoring Factory Default Parameters

To restore factory default parameters:

• disconnect power supply;

• short circuit (connect) connectors DEFAULT;

• connect power supply for 5 seconds;

• disconnect power supply;

• disconnect connectors DEFAULT.

3.2 ET07 Conguration Program

System conguration is performed by using program software ET07 Conguration Tool that can be downloaded from internet

website www.eldes.lt

Before connecting the cable to the computer via USB (or RS232 type) port read ET07 Conguration Tool user manual that can be

found in HELP section of the program.

3.3 Technical Support

Indicator STATUS is o and not blinking • no external power supply

• circuit not properly connected

• blown fuse

• no network signal

Indicator STATUS is blinking several times per second • SIM card is not inserted

• SIM card PIN code request has not been disabled

• SIM card not active

System does not deliver any SMS messages • SIM card account depleted

• incorrect SMS central number

• no network signal

• user telephone number is not programmed in users list

• user telephone number is indicated improperly (read more

about it in ET07 Conguration Tool user manual which can

be founf in Help section of the program)

If your problem could not be xed by the self-guide above, please contact your distributor or ELDES technical support by e-mail

[email protected]. More up to date information about your device and other products can be found at the manufacturer’s website

www.eldes.lt

Pagaminta Lietuvoje. Made in Lithuania.   .

www.eldes.lt

Tabla de contenidos

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario