Elation Lumina Strip Manual de usuario

Lumina Strip

USER MANUAL

Version 1.2 24-004-3557-00

90040-3402

GENERAL INSTRUCTIONS

WARNINGS

After use, the front panel is extreme hot. Please wait at least 15 min. for absolute cool before touching it.

Otherwise, it causes the result of burning.

Thanks for your purchasing Lumina Strip lighting equipment, which is available in Warm White (WW) version.

The Lumina Strip is compatible of both DMX & RDM and with 10 channel LED intensity adjustable. Programs

can be updated via RDM interface. It is available in master and slave control connection. It is easy for users to

install and operate.

For the optimum operation and best performance, please read the instruction in this manual carefully and

thoroughly.

This device is not suitable for direct mounting on normally flammable surfaces. To keep a minimum 0.2m

safety distance to any flammable materials.

DO NOT make any inflammable liquids, water or metal objects enter the unit.

This unit contains no user serviceable parts inside. This unit contains dangerous voltages, always remove

the power plug from the wall socket before any service operation and when not in use for a long time.

Earth connection is so essential.

Stop using the unit immediately in the event of serious operation problems and either contact your local

dealer for a check or contact us directly.

PHYSICAL DIMENSIONS

To protect against high electric shock and injury to person, DO NOT open or dismantle the unit.

NEVER try to repair the unit yourself. Repair by unqualified people could cause damage or mis-operation.

Lumina Strip

1. The unit power cable (1pcs)

2. Wing screw(2pcs) + Grommet(2pcs) + Washer(2pcs)

3. Mounting Assemble(2pcs)

Standard DMX 5-pin In/Out

16 built-in programs except for Auto & Full subject to Speed and Dimmer

0-100% dimming level

Standard DMX-512 protocol

01 Thru 100 Chase Speed adjustment

Power failure memory

MAIN FEATURES

LED display window-shows current activity and function state

On/Off switch

Fuse protection

Accessories(Included):

Before use, make sure whether four screws are secured firmly, if not, please secure them with the screwdriver,

loose 4 screws for lamp replacement.

The unit has also been designed to hold up as user's desire. So you can fix the unit on the holder by the wing

screw. They are placed in the accessory bag, included.

The following installation diagrams are for user reference.

INSTALLATION

Method 1 Method 2

Note :

Once this unit is for hanging application, it is required to use a safety rope (sold separately, which can hold

at least 10 times the weight of the fixture ) to ensure the mounting safety of the fixture by attached through

the holder.

07, 08, 10,11, 16 DMX Channels selection

Lumina Strip

Power:

Before plugging your unit in, be sure the resource voltage in your area matches the unit required voltage.

The unit is available in a 230V version only. Because the line voltage may vary from venue to venue, you

should be sure to plug the socket into a matching wall outlet before attempting to operate your unit.

Fuses:

The Lumina Strip electric system is protected by T3.15A 250V 5*20mm. Please see the printing on the case

and these fuses prevent you from overloading damaging your unit. To replace the protective fuse, use a flat

head screwdriver to unscrew the fuse holder. Pull out the old fuse and replace it with a new one. Insert the

fuse back into the slot and tighten. Always replace with exact same type fuse removed unless otherwise

specified by an authorized service technician,

SYSTEM CONNECTION

Maximum amount of this units that may be connected is 16pcs(AC100-120V) or 32pcs(220-240V).

One universe DMX can drive up to 32 pcs of Lumina Strip, please add DMX booster if Lumina Strip are

connected together in line over 32 pcs or data cable over 100M. The connections may be illuminated

as following.

3pin P ower Ca ble

5pi n DMX Cab le

DMX IN

12332

POWER IN

DMX IN

POWER OUT

DMX OUT

Lumina Strip

POW ER IN

AC1 00-24 0V 15A MAX

3pin P ower Ca ble

5pi n DMX Cab le

DMX IN

12332

POWER IN

DMX IN

POWER OUT

DMX OUT

Lumina Stri p

POW ER IN

AC1 00-24 0V 15A MAX

3pin P ower Ca ble

5pi n DMX Cab le

DMX IN

12332

POWER IN

DMX IN

POWER OUT

DMX OUT

Lumina Stri p

POW ER IN

AC1 00-24 0V 15A MAX

3pin P ower Ca ble

5pi n DMX Cab le

DMX IN

12332

POWER IN

DMX IN

POWER OUT

DMX OUT

Lumina Stri p

POW ER IN

AC1 00-24 0V 15A MAX

3pin P ower Ca ble

5pi n DMX Cab le

DMX IN

12332

POWER IN

DMX IN

POWER OUT

DMX OUT

Lumina Stri p

POW ER IN

AC1 00-24 0V 15A MAX

Lumina Strip

POW ER IN:

100 -240V ~, 50/6 0Hz

FUS E:

T3. 15A 250V 5 x20mm

Pow er Cons umpti on:

90W m ax.

WARN ING: / ATTE NTION :

DRY LO CATION S

EMP LACEM ENTS SE CS

NOT F OR RESI DENTI AL / HOUSE HOLD US E.

PAS PO UR USAG E RESID ENTIE L / M ENAGE .

RIS K OF FIRE AN D ELECT RIC SHO CK

RIS QUE DE CH OC ELEC TRIQU E ET INCE NDIE

FOR SUPPLY CO NNECTIONS USE W ITH WIRE RATED AT LEAST 60 C

POUR LES C ONNEXIONS D' ALIMENTATION DE FIL D'U NE NOTATION

MINIMAL E DE 60 C

MINIMU M SAFETY DISTANCE TO FL AMMABLE MATERI ALS: 0.2m.

DISTANCE DE S ECURITE AUX MATERIAU X COMBUSTI BLES: 0.2m.

MAXIMU M OPERATING TEMPE RATURE OF ENCLOSU RE SURFACE IS 60 C

TEMPER ATURE DE FON CTIONNEMEN T DE SURFACE ENCEIN TE EST A 60 C

FUSE

POWER

MOD E MEN U

RDM/ DMX

POWE R

UP DO WN

Mad e in Chin a

RDM /DMX OU T

POW ER THRU (15A Max .)

Ear th

Neu tra l

Liv e

RDM /DMX IN

POW ER IN(1 5A Max.)

Ear th

Neu tra l

Liv e

Safety chain/cord Safety chain/cord

attachment pointattachment point

Safety chain/cord

attachment point

1=Ground

2=Data-

3=Data+

4,5=NC

1=Ground

2=Data-

3=Data+

4,5=NC

MODE MENU DISPLAY

DMX

Pro gr am

Add re ss

Cha nn el

No DM X

Gli de

Pro gr am

Spe ed

Mas te r

Lam p Mode

Fad e Time

001 - - 512

07 / 08 / 1 0 / 11 / 16

OFF / H old / Pro gram

OFF / O N

Ful l / 01-- 16 / Au to

01 -- 1 00

00 -- 1 00

Tung ste n / LED

00 -- 1 00

40 C

0.2m

Lumina Strip

FOR S AFETY I NSTRU CTION AN D MOUNT ING OPT IONS RE FER TO USE R MANUA L

Layout Overview

1. Lamp: Totally 10 LEDs* Warm White, 7W

1. LCD Display

This multi-function display will detail all DMX Address, Chase , Program, Speed activity that pertains to the

current operation mode of the unit.

2. Mode button

This button will call up the unit operation mode between DMX and Chase mode.

3. Menu button

This button will active the different functions in Receive and Chase modes.

Front Panel Overview

Rear Panel Overview

2 3 4 5

101

Note: In the Chase mode, Menu key is used to only activate Chase Dimmer, Chase Program, Chase Speed,

Fade Time and Lamp Mode. While in the " Receive " mode, only used to only select DMX Address, Channel.

4. UP button

This button will increase the displayed value in the LED display.

5. Down Key

This button will decrease the displayed value in the LED display.

6. DMX Out

This connector sends your DMX signal through to the next unit.

7. DMX In

This connector accepts your DMX input signal.

8. Power Input:

AC100-240V~50/60Hz, Max15A. The supply power is input into your unit via this connector. Be sure to

always connect to proper voltage.

9. Power Thru:

AC100-240V~50/60Hz, Max15A. This connector sends the supply power to the next unit.

10. Fuse:

F3.15A 250V 5*20mm. These fuses prevent you from overloading damaging your unit. Be sure to always

replace with the exact same type fuse.

11. Power Switch:

Turn on/off the power supply.

Lumina Strip

LCD Display / Menu System

MODE ME NU

RDM/ DM X

POWE R

UP DOWN

LCD Display

Mode Key

Menu Key Up Key

Power indicator

RDM/DMX indicator

Down Key

Lumina Matrix LED Menu Tree

OPERATION MODES

The “Lumina Strip” has two different operation modes. It can be used as a 07, 08, 10,11, 16 channel DMX dimmer. Tap “Mode”

button to switch the operation mode between “Receive Mode” and “Chase Mode”. Please follow illustrations below to

operate the unit in your desired mode.

Use this operation mode only when you are about to use the unit as a DMX dimmer. This function can allow

SA-10 LED DMX Map

you set your unit dimmer function as a 07, 08, 10,11 or 16 channel DMX dimmer and DMX address. Tap “Mode”

button to switch the operation mode between “DMX” and “Program”.

DMX Mode

Mode Parameter Parameter Value Function

DMX

Program

Address

Channel

No DMX

Glide

Program

Speed

Master

Lamp Mode

Fade Time

001-512

07/08/10/11/16

OFF/Hold/Program

OFF/ON

Full/01--16/AUTO

01-100

00-100

Tungsten/LED

00-100

To set the initial DMX receiving address

To set the DMX Control Mode

To set the status of the fixture when DMX signal is input

To set the output of the DMX Data

To select a built-in program

To set the speed level of the built-in Program

To set the intensity

To set the mode of Lamp

To set the speed of the Fadetime

Lumina Strip

DMX Channel Details

LED 1-10

LED 1-5 LED 6-10 Programs Program

Speed

Program

Fade

Master

Dimmer

Master Dim

Fine

0-255 0-255 0-255

16-bit

0-255 0-255

(Slow (Less

0-255 Stage (dr 2)

Standard(dr 1) 0-20

21-40

41-60

61-80

81-100

101-255

Theatre(dr

Default to

Unit Setting

TV (dr 3)

(dr 4)

Programs

Master

Dimmer

Master Dim

Fine

Program

Speed

Program

Fade Dim Mode

Dim Mode

8 Bit

7 Channel Configuration

8 Channel Configuration

10 Channel Configuration

0-255

bright bright bright bright Fast More

0-255

0-255 0-255 0-255 0-255

Standard (dr 1)

Stage (dr 2)

TV (dr 3)

Architectural

(dr 4)

Theatre(dr 5)

Default to

Unit Setting

0-20

21-40

41-60

61-80

81-100

101-255

Lumina Strip

11 Channel Configuration

16 Channel Configuration

8 Channel Configuration

16 Bit

Master Dim

16-bit

0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255

Dim Mode

Standard (dr 1)

Stage (dr 2)

TV (dr 3)

Architectural

(dr 4)

Architectural

(dr 4)

Architectural

(dr 4)

Theatre (dr 5)

Default to Unit

Setting

Default to Unit

Setting

Default to Unit

Setting

0-20

21-40

41-60

61-80

81-100

101-255

0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255

Master Dim Dim Mode

0-255 0-255 0-255 0-255 0-255

LED 1&10

0-255 0-255 0-255 0-255 0-255 0-255 0-255

LED 1&10 Master

Dim Fine

Dim Mode

16-bit

10 Channel Configuration

16 Channel Configuration

26 Channel Configuration

Lumina Strip

Dim Mode

Master

Dim Fine

16-bit Standard (dr 1)

Standard (dr 1)

Stage (dr 2)

TV (dr 3)

Architectural

(dr 4)

Architectural

(dr 4)

Architectural

(dr 4)

Theatre (dr 5)

Default to Unit

Setting

Default to Unit

Setting

Default to Unit

Setting

0-20

21-40

41-60

61-80

81-100

101-255

0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255

Master

Dim Fine Dim Mode

16-bit

0-255

Dim Mode

0-255

0-255 0-255

0-255

0-255 0-255 0-255

(16bit Fine) (16bit Fine) (16bit Fine) (16bit Fine)(16bit Fine) (16bit Fine) (16bit Fine)

(16bit Fine) (16bit Fine)

Master

Dim Fine

(16bit Fine)

Tabla de contenidos

Otros manuales de Equipo de iluminación de Elation

Elation

Elation KL PANEL PO Manual de usuario

Elation

Elation Design LED 12 Brick II Manual de usuario

Elation

Elation Design LED Par Zoom MH Manual de usuario

Elation

Elation 6+ Series Manual de usuario

Elation

Elation Level Q7 IP Manual de usuario

Elation

Elation Eled Light Manual de usuario

Elation

Elation Power Spot 700 Manual de usuario

Elation

Elation Level Q7 IP Manual de usuario

Elation

Elation 216 Manual de usuario

Elation

Elation Design LED 36 Brick Manual de usuario

Elation

Elation Pixel Driver 170 Manual de usuario

Elation

Elation Design LED 36 Tri-Brick Manual de usuario

Elation

Elation DW PROFILE Manual de usuario

Elation

Elation Color Spot 575 Manual de usuario

Elation

Elation EPAR TRI Manual de usuario

Elation

Elation Design LED 60 TriStrip Manual de usuario

Elation

Elation KL FRENSEL 6 Manual de usuario

Elation

Elation SEVEN PAR 19IP Manual de usuario

Elation

Elation ELAR EXTQW FLOOD HP Manual de usuario

Elation

Elation Arena Par Manual de usuario

Elation

Elation OPTI TRI WHITE II Manual de usuario

Elation

Elation High Output LED Color Changer Opti RGB Manual de usuario

Elation

Elation Patend Light 1200 HMI Manual de usuario

Elation

Elation EVLED256 Video Wall Instrucciones de instalación

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario