Elation 36 PRO Manual de usuario

Rev. 10/04/2009 – visage Ver. 1.4

Design LED 36 Pro

Elation Professional™

6122 S. Eastern Ave.

Los Angeles, Ca 90040

www.elationlighting.com

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 1 www.ElationLighting.com

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 2 www.ElationLighting.com

TABLE OF CONTENS

1. General Information……………………………………………………………………… 3

a. Introduction………………………………………………………………………. 3

b. Unpacking………………………………………………………..…………..….. 3

c. Customer Support…………………………………………….………………… 3

d. Warranty Registration……………………………………………………………4

2. Safety Instructions………………………………………………………........…………. 5

3. Features……………………………………………………………………………………7

4. General Guidelines………………………………………………………………………. 8

5. Fixture Overview…………………………………………………………………………. 9

6. Mounting and Installation………………………………………………………….……. 11

a. Yoke Assembly………………………………………………………………….. 11

b. Mounting Positions……………………………………………………………… 12

c. Mounting Points…………………………………………………………………. 12

d. Clamp Mounting…………………………………………………………………. 12

e. Securing………………………………………………………………………….. 13

7. Understanding DMX……………………………………………………………………... 14

a. DMX Connections………………………………………………………………. 15

b. DMX Terminator…………………………………………………………………. 15

c. 3-Pin to 5-Pin Conversion……………………………………………………….16

d. Fixture DMX Addressing.……………………………..………………………… 16

8. Display LED Indicators..………………………………………………………………….18

9. Display Menu..………………………………………………………………………….…19

10. DMX Traits…………………………………………………………………………………21

a. 3-Channel Mode………………………………………………………………… 21

b. 4-Channel Mode…..…………………………………………………………..… 22

c. 6-Channel Mode…..……………………………………………..……………… 23

11. Lens Replacement……… ……………………………………………………………… 25

12. Cleaning and Maintenance……………………………………………………………… 26

13. Warranty…………………………………………………………………………………... 27

14. Photometric Data………………………………………………………………………… 29

15. Dimensional Drawings………………………………………………….……………….. 32

16. Circuit Schematic………...………………………………………………………………. 33

17. Technical Specifications…………………………………………...………….………… 34

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 3 www.ElationLighting.com

1. GENERAL INFORMATION

INTRODUCTION: Congratulations, you have just purchased one of the most innovative and

reliable LED fixtures on the market today! The Design LED 36 Pro™ has been designed to

perform reliably for years when the guidelines in this booklet are followed. Please read and

understand the instructions in this manual carefully and thoroughly before attempting to

operate this unit. These instructions contain important information regarding safety during

use and maintenance.

UNPACKING: Thank you for purchasing the Design LED 36 Pro™ by Elation Professional®.

Every Design LED 36 Pro™ has been thoroughly tested and has been shipped in perfect

operating condition. Carefully check the shipping carton for damage that may have occurred

during shipping. If the carton appears to be damaged, carefully inspect your fixture for

damage and be sure all accessories necessary to operate the fixture have arrived intact. In

the event damage has been found or parts are missing, please contact our customer support

team for further instructions. Inside the box you should find: the fixture, a DMX XLR cable, a

safety cable, and this manual. Please do not return this unit to your dealer without first

contacting customer support at the number listed below.

CUSTOMER SUPPORT: Elation Professional®provides a customer support line, to provide

set up help and to answer any question should you encounter problems during your set up

or initial operation. You may also visit us on the web at www.elationlighting.com for any

comments or suggestions. For service related issue please contact Elation Professional®.

Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.

Voice: (323) 582-3322

Fax: (323) 832-9142

E-mail: [email protected]

Forum: www.ElationLighting.com/forum

Warning! To prevent the risk of fire and reduce the risk electrical shock do not attempt to

operate this fixture with the lens cover removed.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 4 www.ElationLighting.com

yourself. Doing so will void your manufactures warranty.

Please do not discard the shipping carton in the trash. Please recycle whenever possible.

WARRANTY REGISTRATION: The Design LED 36 Pro™ carries a two year (730 days)

limited warranty. Please fill out the enclosed warranty card to validate your purchase. All

returned service items whether under warranty or not, must be freight pre-paid and

accompany a return authorization (R.A.) number. The R.A. number must be clearly written

on the outside of the return package. A brief description of the problem as well as the R.A.

number must also be written down on a piece of paper and included in the shipping

container. If the unit is under warranty, you must provide a copy of your proof of purchase

invoice. Items returned without a R.A. number clearly marked on the outside of the package

will be refused and returned at customer’s expense. You may obtain a R.A. number by

contacting customer support at (323) 582-3322.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 5 www.ElationLighting.com

2. SAFETY INSTRUCTIONS

To guarantee proper and consistent operation, it is important to

follow the guidelines in this manual. Elation Professional will not

accept responsibility for damages resulting from the misuse of

this fixture due to the disregard of the information printed in this

manual.

1. If any of the external cables of this fixture become damaged, they should be

replaced only by Elation or an authorized service center or a similar qualified

person in order to prevent possible electrical shock.

2. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.

Although this fixture shares a case design with our outdoor rated DLED 108IP,

this version has not been approved for outdoor use. Use of this fixture outdoors

will void all manufactures warranty.

3. Always be sure that the fan and the air inlets remain clean and are never

blocked. Allow about 6” (15cm) between this fixture and other devices or a wall

to allow for proper cooling.

4. Never touch the fixture during normal operation.

5. Never look directly into the light source. You risk injury to your retina, which may

induce blindness.

6. For safe operation, follow the Installation guide described in chapter six of this

manual. Operating the Design LED 36 Pro™ without suited safety aids such as

safety cables or clamps can increase the risk of damage and/or personal injury.

7. Qualified and certified personnel should only perform installation.

8. When mounting this fixture, use only the original rigging points included with this

fixture. Any structural modification will void the original manufactures warranty

and may increase the risk of damage and/or personal injury.

9. Do not attempt to operate this fixture if the power cord has become damaged or

frayed.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 6 www.ElationLighting.com

10.Never open this fixture while in use.

11.This device falls under protection-class I. Therefore it is essential that the device

be grounded properly.

12.Qualified personnel should perform all electrical connections.

13.Be sure the available voltage matches the voltage requirements of the unit. Be

sure the power cord is never crimped or damaged. If the power cord is damaged,

replace it immediately with a new one of similar power rating.

14.Always disconnect from main power before performing any type of service or

any cleaning procedure.

15.Only handle the power cord by the plug. Never pull out the plug by tugging the

wire portion of the cord.

16.Please be aware that damages caused by modifications to the device are

not subject to warranty.

Important Notice: Damages resulting from the disregard of safety and general user

instructions found in this user manual are not subject to any warranty claims.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 7 www.ElationLighting.com

3. FEATURES

• Low power consumption

• Minimal heat emission

• Maintenance free operation

• Equipped with 36 3-Watt (12 x red, 12 x green, 12 x blue)

• Silent Operation, convection cooled, no fans

• 100,000 hours rated LED life

• Linear RGB Color Mixing, infinite color possibilities

• 20˚ Standard Beam Angle (15˚ Lens - Optional 25˚ & 45˚ Lens Kits Available)

• 40˚ Standard Field Angle (15˚ Lens - Optional 25˚ & 45˚ Lens Kits Available)

• USITT DMX-512 Complaint

• Preprogrammed colored macros

• Strobe-effect with a maximum flash rate of 18fps

• DMX-controlled operation or stand-alone operation with Master/Slave-function

• 7 built-in programs can be called up via DMX-controller

~ 48 preprogrammed scenes per program

• Sound-controlled via built-in microphone

• Three DMX Modes:

6 DMX channels

4 DMX channels

3 DMX channels

• DMX-control via standard DMX-controller

• Power Switching Electronic Power Supply 100v~240v

• Flicker-free operation for television and film

• Compact design: fits in 12” box truss

• 0%~100% Dimming (two dimming options; linear & standard)

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 8 www.ElationLighting.com

4. GENERAL GUIDELINES

This fixture is a professional lighting effect designed for use on stage, in nightclubs, in

theatres, and other types of architectural installations. Do not attempt operation or

installation without a proper knowledge on how to do so.

This fixture was designed for indoor use only; use of this fixture outside will void the

manufacture’s warranty.

Consistent operational breaks will ensure that the fixture will function properly for many

years to come.

Do not shake the fixture around. Avoid brute force when installing or operating the fixture.

While choosing an installation location, please be sure that the fixture will not be exposed to

extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or flat

surface should be at least 0.5 meter (about 1.5ft). See page 11.

Always install the fixture with an appropriately rated safety cable. When installing the fixture

in a suspended environment always be sure to use mounting hardware no less than M10 x

25 mm, also be sure the hardware is only inserted in the yoke’s mounting holes.

Do not attempt to operate this fixture until you have familiarized yourself with all of its

functions.

Do not permit operation by persons not qualified for operating this type of architectural

fixture. Most damages are the result of improper operation.

Please use the original packaging to transport the fixture in for service.

For your own safety, please read this user manual carefully before installing the device.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 9 www.ElationLighting.com

5. FIXTURE OVERVIEW

1. LED Lens Assembly – The lens assembly may be user replaced in the event repair

is needed or a different beam angle is required.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de Elation

Elation

Elation Opti Tri 30 Manual de usuario

Elation

Elation EVENT PANEL SYSTEM Manual de usuario

Elation

Elation Level Q7 IP Manual de usuario

Elation

Elation ELAR EXQUADPAR HP Manual de usuario

Elation

Elation Color Spot 575 Manual de usuario

Elation

Elation Platinum Spot LED Pro Manual de usuario

Elation

Elation ELAR 180 Par RGBAW Manual de usuario

Elation

Elation KLF060 Manual de usuario

Elation

Elation Event Par System Manual de usuario

Elation

Elation FUZE PAR Z175 Manual de usuario

Elation

Elation Design Spot 300E Manual de usuario

Elation

Elation Elation DMX OPERATOR PRO Manual de usuario

Elation

Elation Pixel Driver 170 Manual de usuario

Elation

Elation Patend Light 1200 HMI Manual de usuario

Elation

Elation Design 60 Tri Manual de usuario

Elation

Elation FUZE WASH 500 Manual de usuario

Elation

Elation Arena Par Manual de usuario

Elation

Elation EPAR QA Manual de usuario

Elation

Elation TVL3000WW Manual de usuario

Elation

Elation KL FRENSEL 8 Manual de usuario

Elation

Elation Outdoor LED Par Fixture ELAR EXPAR Manual de usuario

Elation

Elation EVLED256 Video Wall Instrucciones de instalación

Elation

Elation Design Beam 300 Manual de usuario

Elation

Elation Outdoor LED Par Fixture ELAR EXPAR Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario