Elatec TWN4 Slim LEGIC Manual de usuario

RFID Reader

TWN4 Slim LEGIC

User Manual

DocRev 2

ELATEC GmbH

Page 2 of 8

1. Introduction

The TWN4 Slim LEGIC is ELATEC’s smallest compact & flat RFID reader –

it’s smaller than an ID-1 card. TWN4 Slim supports a huge range of LF and

HF technologies (125 kHz and 13.56 MHz). With the support of NFC and

Bluetooth Low Energy the reader supports mobile use cases for data

communication and authentication. It can be operated as a stand-alone unit

and connected using a standard cable with a micro USB plug to PCs and

other devices with USB interface. TWN4 Slim LEGIC is perfectly suited to

embed it into machines and devices, and especially MFP printers. By using

clip-on covers, TWN4 Slim LEGIC is mountable into printer chassis cavities

and allow a flat and even surface –invisible integration.

ELATEC GmbH

Page 3 of 8

2. Getting Started

2.1 Operating mode

In order to start operating a TWN4 Slim LEGIC, it simply has to be connected

directly to a host device.

2.2 Power Supply

Requirement for the external power supply unit:

- Limited Power Source according to IEC 60950-1 or

- PS2 classified IEC 62368-1

- Short-circuit current < 8A

2.3 Enumeration

Once the device has been powered up, it is waiting for completion of the

enumeration by the USB host. As long as the device is not enumerated, it is

entering a minimum power consumption mode.

2.4 Initialization

After powering up and enumeration the device is turning on the built-in

transponder reader logic. The green LED is turned on permanently. Some

transponder reader modules need some kind of initialization, which is

performed in this step. After successful initialization, the device sounds a

short sequence, which consists of a lower tone followed by a higher tone.

ELATEC GmbH

Page 4 of 8

2.5 Normal Operation

As soon as the device has completed the initialization, it is entering normal

operation. During normal operation the device is searching for a transponder

continuously.

2.6 Detection of a Transponder

If a transponder is detected by the reader, following actions are performed

•Send the ID to the host. By default, the USB device sends by

emulating keystrokes of a keyboard. A RS232 device sends the

ASCII code of an ID.

•Sound a beep

•Turn off the green LED

•Blink the red LED for two seconds

•Turn on the green LED

Within the two seconds timeout, where the red LED is blinking, the

transponder, which just has been recognized will not be accepted again. This

prevents the reader from sending identical IDs more than one time to the

host.

If during the two seconds timeout of the red LED a different transponder is

detected, the complete sequence restarts immediately.

2.7 Suspend Mode

Once the host is resuming to normal operation mode, this is also signaled

via the USB bus. Therefore, the transponder reader will resume to normal

operation, too.

ELATEC GmbH

Page 5 of 8

3. List of Antennas

LF-Antenna

HF-Antenna circulating the

PCB (inside the inner layers)

BLE-Antenna

(Johanson Technology

2450AT18A100)

ELATEC GmbH

Page 6 of 8

Compliance statements

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Caution!

The Federal Communications Commission (FCC) warns the users that

changes or modifications to the unit not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

FCC §15.105 (b):

Note: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reason-able protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be deter-mined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

The product is FCC Rule Part 15B SDoC conform.

ELATEC GmbH

Page 7 of 8

Canada Compliance

This device complies with Industry Canada’s license-exempt RSSs.

Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables

aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes:

1) l’appareil ne doit pas produire de brouillage;

2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

RF exposure statement (mobile and fixed devices)

This device complies with the RF exposure requirements for mobile and fixed

devices. However, the device shall be used in such a manner that the

potential for human contact during normal operation is minimized.

RF exposure statement portable devices) This device complies with the RF

exposure SAR test exclusion requirements for portable devices, if a minimum

separation distance 20 cm is kept. However, the device shall be used in such

a manner that the potential for human contact during normal operation is

minimized.

注意!

依據低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均

不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干

擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依

電信規定作業之無線電信。低功率射頻電機須忍受合法通信或工業、科學及醫療

用電波輻射性電機設備之干擾。

ELATEC GmbH

Page 8 of 8

México

La operación de este equipo está sujeta a las siguientes dos condiciones:

(1) Es posible que este equipo o dispositivo no cause interferencia perjudicial

(2) Este equipo o dispositivo debe aceptar cualquier interferencia,

incluyendo la que pueda causar su operación no deseada.

Brazil

Este equipamento não tem direito à proteção contra interferência prejudicial

e não pode causar interferência em sistemas devidamente autorizados.

4. Service Address

In case of any technical questions, please contact:

ELATEC GmbH

Zeppelinstr. 1

82178 Puchheim

Germany

Phone: +49 (0) 89 5529961 0

Fax: +49 (0) 89 5529961 129

E-mail: [email protected]om

Otros manuales para TWN4 Slim LEGIC

Tabla de contenidos

Otros manuales de Sistema RFID de Elatec

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Elatec

Elatec TWN4 MULTITECH 3 LEGIC M LF HF Manual de uso y cuidado

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Elatec

Elatec TWN4 MULTITECH NANO LEGIC 63 M Manual de uso y cuidado

Elatec

Elatec TCPConv Manual de usuario

Elatec

Elatec TWN4 Palon Compact Manual de usuario

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Elatec

Elatec TWN3 MIFARE Manual de usuario

Elatec

Elatec TWN4 MultiTech 2 HF Manual de uso y cuidado

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Elatec

Elatec TWN4 MultiTech 3 LEGIC M BLE Manual de usuario

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Elatec

Elatec TWN4 Palon One LEGIC Nota de versión

Elatec

Elatec MULTITECH 2 M HF Manual de usuario

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Elatec

Elatec TWN4 MultiTech 2 HF Manual de uso y cuidado

Elatec

Elatec MultiTech M TWN4 Manual de usuario

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Elatec

Elatec TWN4 Slim Manual de usuario

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Elatec

Elatec TWN4 MultiTech 2 HF Manual de usuario

Manuales populares de Sistema RFID de otras marcas

Chainway

Chainway R1 Manual de usuario

IFM

IFM DTC600 Manual de usuario

RHOMBUS

RHOMBUS DR20 Manual de usuario

Sirit

Sirit IDentity 6204 Manual de usuario

SOREX

SOREX FLEX Manual de usuario

Omron

Omron V780-HMD68-EIP-KR Manual de usuario

IDENTEC SOLUTIONS

IDENTEC SOLUTIONS iPOINT Si Instrucciones de uso

Shuttle

Shuttle BR06 Instrucciones de uso

Digilock

Digilock Curve Keypad Basic Manual de usuario

Atid

Atid AT870 Manual de usuario

Chacon

Chacon 34958 Manual de usuario

Paxton

Paxton PROXIMITY architectural reader Manual de usuario

CipherLab

CipherLab 1800 series Manual de usuario

Brady

Brady FR22 Manual de usuario

Kronotech

Kronotech BLUEBOX GEN2 M30 UHF Manual de usuario

Unitech

Unitech RH767 Manual de usuario

Honeywell

Honeywell 026366.00 Manual de usuario

OLIMEX

OLIMEX MOD-RFID125-BOX Manual de usuario