ELAN Lighting TRANSCEIVER WS Manual de usuario

TRANSCEIVER WS

RECEIVER WS

User manual

On the Transmitter, press and hold the FUNCTION button until LINK begins ashing. All

registered Receivers linked to that Transmitter will be unlinked.

3.4 To unlink all Receivers

The TRANSCEIVER can be used as a Transmitter or Receiver. To switch mode between

Transmitter and Receiver, power o the unit, then hold the FUNCTION button while power on

the unit for 2 seconds. When DMX and MODE indicators turn o, then the unit is a Receiver.

Otherwise, it is a Transmitter.

3.5 To set a TRANSCEIVER to Transmit or Receive

IMPORTANT INFORMATION!

In order to optimize the recovery and recycling of the materials that old

appliances contain and reduce the impact on human health and the

environment, ensure that this product is recycled at the end of its life.

5. Specifications

FCC Notice

• Frequency band: 2.4GHz

• Transmission distance: approx. 500m

• IP rating: IP20

• Power supply: AC 230V 50-60Hz

• Dimension: 145mm x 100mm x 57mm

• Weight: 1.40kg

Note: The Receiver will stay linked/logged on to the Transmitter no matter DMX

signal or power is cut o. The log-in information is stored in an EEPROM and will not

be erased.

•

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference,and (2) this device must accept any

interference received, including interference that may cause undesired operation.

• Changes or modications not expressly approved by the manufacturer responsible

for compliance could avoid the user’s authority to operate the equipment.

The WIRELESS DMX system is compact, lightweight and durable. Utilizing AFHSS - Adaptive

Frequency Hopping Spread Spectrum technology, the wireless system transmits or receives

safe and reliable DMX data without any delay and interference. Ideal for rental, mobile show,

event, club, DJ, etc. Please read this user manual carefully and thoroughly before

operation.

1.1 Unpacking

1.2 Safety Instructions

Carefully unpack the carton, check the contents to ensure that all parts are present,

and have been received in good condition. Contact your supplier immediately and

retain packing material for inspection if any part is missing or damaged.

1. INTRODUCTION

■1 x TRANSCEIVER WS or RECEIVER WS

■1 x Power cable

■1 x Mounting bracket

■1 x User Manual

Warning!!! To reduce the risk of re, electric shock, or injury to persons,

follow these important safety instructions:

The following items are included in the box:

▪This product is intended for indoor use only!

▪Please keep this User Guide for future consultation.

▪Do not attempt to dismantle and/or modify the transmitter in any way.

▪To prevent risk of re or shock, do not expose xture to rain or moisture.

▪Make sure that the voltage and frequency of power supply match the power

requirements of the transmitter/receiver.

▪Make sure power cord is never crimped or damaged.

▪The transmitter is only intended for installation, operation and maintenance by

qualied personnel.

1.3 Features

• Adaptive Frequency hopping technology - AFHSS

• Completely interference free

• Transmit 512 channels (1 universe) of DMX data

• Maximum 16 universes of DMX in one area

• One-button-go for quick setup

1) Power on the Receiver unit(s) and ensure that they are not linked with any other transmitter

(LINK indicators should be OFF).

2) Press and quickly release FUNCTION button on the Transmitter. The transmitter will scan for

all unlinked receivers for a period of 10 seconds - the LINK indicator on both the Transmitter

and Receiver(s) will ash rapidly.

3) If succefssful, the LINK indicator on Receiver(s) now go ON. If any failed, check that the

Receiver is in range and repeat procedure.

3.2 To add Receivers

Press and hold the Function button on the Receiver for about 3 seconds till the LINK indicator

go o. Now the Receiver is unlinked.

Note: You can add receivers at any time, even during operation. In an operational

system, logging on an additional receiver will make the logged-in units revert to

idle mode for 10 seconds; once the new units are logged-in they will all start again

together with the new unit.

3.3 To unlink a Receiver

Multipoint-to-multipoint

Up to 16 universes of DMX can be transmitted simultaneously using multipoint to

multipoint operation. All receivers in a multipoint system will listen only to the

designated transmitter without any delays or interference from other systems

working alongside.

DMX

1.4 Product overview

2. SETUP

2.1 Placing Transmitter and Receiver

For successful linking, the following conditions should be fullled:

2.2 Placing Transmitter and Receiver

The Wireless unit can be mounted onto truss with the mounting bracket (included).

a. Distance between Transmitter and Receiver should not exceed 200m.

b. Position of Transmitter and Receiver should be 1m at least above crowds and trees .

• Plug and play, no need conguration for IP address

• Point-to-point, point-to-multipoint or multpioint-to-multipoint operation

Function button DMX In/DMX OutOn/O Power In Fuse

500m max. in line of sight

1m min.

TRANSMITTER RECEIVER

3. OPERATION INSTRUCTIONS

2.3 System connection

The wireless system is designed to work on AC 110V or 230V. Before applying power to a unit,

make sure that the unit’s input voltage matches the power source voltage.

Use DMX cables to connect DMX IN of the TRANSCEIVER to DMX source and DMX OUT of

RECEIVER to lighting equipments.

2.4 Power Adapter

3.1 3 types of operation

Point-to-multipoint

Point-to-point

DMX

One Transmitter supports up to 512pcs Receivers in one point-to-muiltipint system.

DMX

Mounting bracket

Este manual sirve para los siguientes modelos

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario