Ekwb EK-Quantum Velocity 2 Manual de usuario

USER GUIDE

EK-Quantum

Velocity² - AM5 Backplate

Please note the installation of the product is intended to be undertaken

by an adequately trained and experienced person. You are installing the

product at your own risk. If you are not properly trained or experienced or

feel unsure about the installation procedure, please refrain from installing

the product yourself and contact our tech support for assistance. We

disclaim our liability for any damages to the product as well as incidental,

consequential, or indirect damages incurred due to improper or

inappropriate installation.

Before you start using this product, please follow these basic guidelines:

Please carefully read the manual before beginning the

installation process.

The EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

The use of corrosion inhibiting coolants is always recommended

for liquid cooling systems, and mandatory for nickel-plated

water blocks.

Do not use pure distilled water! For best results, EK recommends

the use of EK-Cryo Fuel coolants.

Make sure to thoroughly bleed air out of your water block, or

you will not reach optimal performance.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

BACKPLATE DIMENSIONS 5

PREPARING THE AM4 WATER BLOCK FOR UPGRADE 6

PREPARING THE AM5 MOTHERBOARD 7

INSTALLING THE WATER BLOCK 9

CONNECTING THE D-RGB LED STRIP 11

TESTING THE LOOP 11

WARRANTY 12

SUPPORT AND SERVICE 13

SOCIAL MEDIA 13

- 4 -

BOX CONTENTS

AM5 Backplate

Allen Key 2.5 mm (1 pc) TX20 L-Shaped Wrench (1 pc)

Thermal grease (1 pc)

- 5 -

BACKPLATE DIMENSIONS

90 mm

60 mm

43 mm

53 mm

8.9 mm

7.6 mm

6.3 mm

- 6 -

STEP 1

TOP OF THE

MOTHERBOARD

PREPARING THE AM4 WATER BLOCK FOR UPGRADE

Important! Before starting, make sure to have a clean, ﬂat

surface to work on. It is recommended to put foam or soft

material to lay a motherboard on.

STEP 1

If the EK-Quantum Velocity2 AM4 water block is already installed,

remove the backplate from the motherboard’s backside using Allen

Key 2.5 mm (As shown in the picture).

STEP 2

Detach the water block from the motherboard and save it for later

steps. Clean the CPU cold plate using a non-abrasive cloth or Q-tip.

STEP 2

- 7 -

STEP 1

Using a Philips-head screwdriver remove the four screws securing

the original plastic hold-down clamps around the socket as shown in

the illustration. Remove the hold-down clamps and store them away.

PREPARING THE AM5 MOTHERBOARD

UNC 6-32 SCREW

HOLD-DOWN

CLAMPS

STEP 1

STEP 2

After removing the plastic hold-downs, additional four (4) Screws

must be removed using provided TX20 L-shaped wrench. After

removing the screws, detach the factory-provided backplate. Save

the backplate screws for the next step.

STEP 2

BACKPLATE SCREW

FACTORY-PROVIDED

BAC KP L ATE

TX20 L-Shaped Wrench

For this step, you will need:

- 8 -

STEP 3

Attach the AM5 Backplate and secure it with the four (4) saved

backplate screws.

Do not peel off the protective sticker from the AM5 Backplate!

STEP 4

Cleaning the CPU: Wipe the IHS clean using a non-abrasive cloth or

Q-tip as shown in the illustration.

STEP 3

STEP 4

IHS

NON-ABRASIVE CLOTH

AM5 BAC KP L ATE

BAC KP L ATE

SCREW

TX20 L-Shaped

Wrench

AM5 Backplate

Backplate screw

(4 pcs)

For this step, you will need:

- 9 -

STEP 1

Position the AM4 CPU Water Block onto the AM5 Motherboard.

Make sure to align the holes (as shown in the picture).

Make sure to double-check the layer of the Thermal Grease

before placing the water block onto the motherboard.

STEP 1

INSTALLING THE WATER BLOCK

STEP 5

Applying thermal compound: Apply the enclosed thermal grease

(thermal compound) on the CPU heat spreader – IHS – as shown in

the image. The layer of the thermal compound must be thin and even

in thickness over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

STEP 5

Thermal Grease

For this step, you will need:

- 10 -

STEP 3

With EK-Velocity² series water blocks, it is mandatory to use the

bottom port as the INLET.

Mixing the ports may result in poor thermal performance of the

water block.

Tighten the ﬁttings in a clockwise direction until the gasket

underneath is compressed. The installation of the Velocity² water

block is now complete.

OUTLET

INLET

STEP 2

Secure the water block from the backside of the motherboard using

the included Allen Key 2.5mm.

Start fastening the screws in a cross pattern. Do not tighten fully until

all of the screws are partially screwed in.

The Allen Key 2.5mm must be used in a standing position! Otherwise,

the mounting screws may crack during tightening!

Make sure to orientate the backplate as illustrated. Incorrect

installation of the backplate may result in damage to the motherboard.

Allen Key 2.5 mm

For this step, you will need:

MAX TORQUE:

0.6 Nm TOP OF THE

MOTHERBOARD

AM5

BAC KP L ATE

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-FB ASUS PRIME X299 RGB Monoblock Manual de usuario

ekwb

ekwb EK-FC460 GS/SONIC Manual

ekwb

ekwb EK-Annihilator Series Manual de usuario

ekwb

ekwb EK-Nucleus AIO CR360 Vision D-RGB Manual de usuario

ekwb

ekwb EK-FC1080 GTX Ti Aorus Manual de usuario

ekwb

ekwb EK-FCS10000 Manual

ekwb

ekwb EK-FB GA X299 GAMING Monoblock Manual de usuario

ekwb

ekwb EK-RAM Dominator Manual

ekwb

ekwb EK-FB KIT GA Z97X-SOC Force Guía

ekwb

ekwb EK-Quantum Vector RTX 3080/3090 D-RGB Manual de usuario

ekwb

ekwb EK-Supreme HF Guía

ekwb

ekwb EK-Vector Trio RTX 2080 Ti Manual de usuario

ekwb

ekwb EK-D5 Dual TOP CSQ Manual

ekwb

ekwb EK-FC4890CF Guía

ekwb

ekwb EK-FB MSI X399 GAMING RGB Monoblock Manual de usuario

ekwb

ekwb EK-Nucleus AIO CR360 Lux D-RGB Manual de usuario

ekwb

ekwb EK-FC Titan Z Manual

ekwb

ekwb EK-FCQ6000 Manual

ekwb

ekwb 115 Series Manual de usuario

ekwb

ekwb EK-FC670 GTX DCII Guía

ekwb

ekwb EK-AIO 280 D-RGB Manual de usuario

ekwb

ekwb EK-KIT HT Series Manual de usuario

ekwb

ekwb EK-FC980 Manual

ekwb

ekwb EK-MSI Z690 Carbon EK X Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-Quantum Velocity 2 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas