Ekwb EK-Pro GPU Quick Disconnect Kit Manual de usuario

INSTALLATION MANUAL

EK-Pro

GPU Quick Disconnect Kit

GPU WATER BLOCK

- 2 -

This product is compatible with all EK water blocks and manifolds. It is

intended for installation by expert users only. Please consult with

a qualiﬁed technician since improper installation may result in damage

to the equipment. EK assumes no liability whatsoever, expressed

or implied, for the use of these products, nor their installation. The

following instructions are subject to change without notice. Please visit

our website at www.ekwb.com for updates. Before the installation of

this product, please read important notice, disclosure, and warranty

conditions printed on the back of the box.

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process and to prevent any possible damages to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw them

ﬁrmly in place since the liquid seal is ensured with the rubber

O-ring gaskets.

The use of quality market-proven corrosion-inhibiting coolants

is always strongly recommended for any liquid cooling system.

Do not use pure distilled water as a cooling liquid! For best

results, EK recommends the use of EK-CryoFuel Coolants.

- 3 -

TABLE OF CONTENTS

PREPARING THE WATER BLOCK 4

REMOVING THE TERMINAL 4

MOUNTING THE NEW TERMINAL 4

MOUNTING THE BARB FITTINGS 5

MOUNTING THE ZMT TUBE 5

MEASURING TUBES 6

SUPPORT AND SERVICE 8

SOCIAL MEDIA 8

- 4 -

PREPARING THE WATER BLOCK

STEP 1

REMOVING THE TERMINAL

Remove all encircled screws using the 2.5mm Allen key and clean

the mounting surface of the water block with a nonabrasive cloth. EK

recommends you use a dry cloth only.

STEP 1

STEP 2

MOUNTING THE NEW TERMINAL

After you have cleaned the sealing surface, assemble the terminal,

as shown in the picture. Make sure that O-rings are correctly placed

into terminal channels. Once the terminal is in the right position on

the water block, insert and tighten the screws with a 2.5mm Allen key

and apply not more than 0.5 - 0.7 Nm of torque to avoid damaging

the water block. EK recommends this installation is done by

expert users only.

STEP 2

OR 15x1

EPDM50

M4x10 DIN7984

M4x28 DIN7984

- 5 -

STEP 3

MOUNTING THE BARB FITTINGS

Once the terminal is in the position and adequately screwed-in,

screw the barb ﬁttings into the G1/4 threaded holes. For tightening,

use a fork wrench 18 with torque adjustment set to 0.8 Nm.

STEP 3

STEP 4

MOUNTING THE ZMT TUBE

For proper installation of ZMT tubes and clamps, EK recommends

the use of adequate hose clamp pliers.

- 6 -

STEP 5

MEASURING TUBES

When measuring the tube length, make sure to avoid any sharp

transitions of the tube to the barb fittings. Take a look at the

illustration for better understanding.

CORRECT

WRONG

Once the ZMT tubes and clamps are mounted, make sure they are

positioned correctly (as shown in the picture).

STEP 5

- 7 -

ADDITIONAL NECESSARY TOOLS

Hose Clamp Pliers

O-Ring OR 15x1

EPDM50 2 pcs

QD2-FS06-P -

Female QDC 2 pcs

TOP Acetal - FC

Terminal M4 Pre-

Filled1 pc

M4x10 DIN7984

Screw 2 pcs

M4x28 DIN7984

Screw 1pcs

BOX CONTENTS

Check the box contents carefully. The O-rings might already be installed

inside the terminal.

QD2-MSG4 - Male

QDC 2 pcs

2.5 mm Allen Key

1 pc

EK-HFB Fitting 6mm

2 pcs

Hose Clamp FSB

Mini 4 pcs

EK-Tube ZMT 6.5/9.5

Matte Black 1,2 m

In case you need assistance, please contact:

http://support.ekwb.com/

EKWB d.o.o.

Pod lipami 18

1218 Komenda

Slovenia - EU

EKWaterBlocks

@EKWaterBlocks

ekwaterblocks

EKWBofﬁcial

SUPPORT AND SERVICE

SOCIAL MEDIA

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de computadora de ekwb

ekwb

ekwb EK-FC GV100 PRO Manual de usuario

ekwb

ekwb EK-FC Titan SE Series Manual

ekwb

ekwb EK-FB ASUS M9A Monoblock Series Manual de usuario

ekwb

ekwb EK-FB ASUS M8G Monoblock Series Manual de usuario

ekwb

ekwb EK-FC7970 Series Manual

ekwb

ekwb EK-XRES D5 Series Manual

ekwb

ekwb EK-Quantum Surface P360M Manual de usuario

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

ekwb

ekwb EK-FC Radeon Vega Strix Series Manual de usuario

ekwb

ekwb EK-FC1080 GTX Ti Aorus Series Manual de usuario

ekwb

ekwb EK-Supremacy EVO RGB Manual de usuario

ekwb

ekwb EK-FB RE3 Manual

ekwb

ekwb EK-FB ASUS ROG R6E Monoblock Manual de usuario

ekwb

ekwb EK-FC R9-290X SE Series Manual

ekwb

ekwb EK-XTOP Revo D5 PWM RGB Series Manual

ekwb

ekwb EK-Supremacy sTR4 Series Manual de usuario

ekwb

ekwb EK-Supreme LTX CSQ Series Manual

ekwb

ekwb EK-FC R9 Nano Manual

ekwb

ekwb EK-FB ASUS M9H Monoblock Series Manual de usuario

ekwb

ekwb EK-DCP Manual

ekwb

ekwb EK-RAM Monarch Series Manual de usuario

ekwb

ekwb EK-FC 6970 V2 Guía

ekwb

ekwb EK-FC 5850 Series Manual

ekwb

ekwb EK-DBAY D5 Manual

Manuales populares de Accesorios de computadora de otras marcas

Motorola

Motorola ATRIX Manual de usuario

HP USB Media Docking Station Manual de usuario

Cherry

Cherry B.UNLIMITED 3.0 Manual de usuario

Logitech

Logitech IO2 Manual de usuario

ARM

ARM DSTREAM-ST Manual de usuario

Bartec

Bartec TC 7 Series Manual de usuario

Philips

Philips SPC3540 Manual de usuario

Logitech

Logitech mk220 Manual de usuario

SilverStone

SilverStone LC02 Manual de usuario

Flexispot

Flexispot ML2B Manual de usuario

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Manual de usuario

Adam Equipment

Adam Equipment RS-485 Manual de usuario

Vivo

Vivo MOUNT-KB05-4DW Manual de usuario

Kvaser

Kvaser Memorator Professional Manual de usuario

DRC

DRC D-Imaging Manual de usuario

Sven

Sven Base 305 сombo Manual de usuario

Hama

Hama 108310 Manual de usuario

SpeechWare

SpeechWare FlexyMike FMK03 Manual de usuario

ekwb EK-Pro GPU Quick Disconnect Kit Manual de usuario

Manuales populares de Accesorios de computadora de otras marcas